用于微型涡轮机的节流孔式静压气浮轴承实验

对用于厘米级微型涡轮发动机的径向静压气浮轴承展开了实验研究,分析了长径比、节流孔径、气膜间隙及供气压力等对承载力、刚度和耗气量的影响.提出了这些设计参数的优选方法,并结合直径11 cm的某微型喷气发动机,给出了与之匹配的径向静压气浮轴承设计方案:工作面直径15 mm、长度17.5 mm、节流孔径0.35 mm、气膜间隙25μm.此方案在供气绝对压力2.5 kPa时,双轴承支撑能力为13.72 N,耗气量小于1.0 g/s,有效地满足了微型涡轮发动机要求.      

低成本捷联惯导不对称动态误差的神经网络补偿

 针对低成本捷联惯导系统(SINS)中陀螺动态误差的不对称性在角振动条件下造成姿态漂移的问题,设计了多层前向神经网络的补偿模型。在标定模型参数时,为降低对外部参考信号测量精度的要求,提出用姿态解算的最终误差作为网络优化目标的训练方法。由于最终的姿态误差不是网络的期望输出,无法采用有导师的训练方法,为此采用了微粒群优化算法。仿真实验结果表明:补偿后的陀螺动态误差的不对称度减小了一个数量级。     

小推力航天器的地月低能转移轨道

 在限制性四体模型下研究基于小推力方式的地月低能转移问题,通过借助于平动点轨道的相空间结构来揭示小推力转移的机理。重点研究了小推力转移自由飞行段的构造：经由LL₁点穿越获得最小能量的低能转移;而经由LL₁点Halo轨道穿越,得到(M,N)圈穿越轨道;由于Halo轨道相对于平动点增加了一维度的选择,根据(2,2)圈穿越轨道构造该转移的自由飞行段。在地球势阱逃逸和月球势阱捕获段,分别设计了合适的小推力的控制律及发动机开/关机时间,成功实施近地球段的小推力加速和近月球段的减速。尽管未对所得到的结果进行优化,所得转移轨道的燃料消耗也与类似边界条件的SMART-1轨道基本一致。     

Aviation-oriented Micromachining Technology-Micro-ECM in Pure Water

This article proposes a precise and ecofriendly micromachining technology for aerospace application called electrochemical machining in pure water （PW-ECM）. On the basis of the principles of water dissociation, a series of test setups and tests are devised and performed under different conditions. These tests explain the need for technological conditions realizing PW-ECM, and further explore the technological principles. The results from the tests demonstrate a successful removal of electrolytic slime by means of ultrasonic vibration of the workpiece. To ensure the stability and reliability of PW-ECM process, a new combined machining method of PW-ECM assisted with ultrasonic vibration （PW-ECM/USV） is devised. Trilateral and square cavities and holes as well as a group of English alphabets are worked out on a stainless steel plate. It is confirmed that PW-ECM will be probably an efficient new aviation precision machining method.     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

基于自动代码生成技术的永磁同步电机控制

为缩短电机控制系统软件开发周期,减少手写代码人力消耗,将自动代码生成技术应用于机载燃油泵用电机控制系统的软件开发中,介绍了自动代码生成技术的特点及开发流程,在MATLABSimulink环境下搭建了基于矢量控制算法的永磁同步电机系统控制模型,通过实验将模型自动生成为嵌入式代码,成功的实现了电机的闭环控制,极大地提高了开发效率,达到了预期成果。     

飞行汽车机翼折叠机构设计

为保证飞行汽车在空中安全飞行、地面稳定行驶的功能需求,机翼折叠机构设计是其中的关键技术。在通过多方案对比分析后,采用折叠机构与传力结构一体化设计技术,设计了基于槽轮原理的机翼折叠机构/结构方案,研制了折叠机构原理验证样机。通过ADAMS运动仿真、结构强度分析和原理试验验证,机翼折叠机构满足折叠功能和承载性能要求。探索了特殊构型下,机翼折叠机构/结构的设计分析方法,为特殊构型飞行器设计和研究提供了技术积累。     

航天器两自由度扫描镜图像运动补偿技术研究

研究航天器的两自由度扫描镜图像运动补偿问题。在姿态估计信息的基础上,给出了一种运动补偿算法。算法中不仅补偿了姿态估计信息,还同时考虑了姿态信息中的长周期系统误差。利用扫描镜在特定工作模式下相对惯性空间的准确定向能力和系统误差的长周期特性,给出了一种系统误差的估计和补偿算法,每隔一定的时间段对系统误差估计值进行更新并加以补偿,进一步提高了扫描精度。基于一颗地球静止轨道卫星的数值仿真结果验证了补偿算法的有效性。     

Comparative analysis of four different single-frequency PPP models on positioning performance and atmosphere delay retrieval

Single-frequency precise point positioning (SF-PPP) has attracted increasing attention due to its high precision and cost effectiveness. With various strategies to handle the dominant error, i.e., ionosphere delay, the ionosphere-float (IF), ionosphere-free-half (IFH), ionosphere-corrected (IC), and ionosphere-weighted (IW) SF-PPP models are certain to possess different characteristics and performance levels. This study is dedicated to assessing and comparing the four models from model characteristics, positioning performance, and atmosphere delay retrieval. The model comparison shows that IC and IW models are full-rank while IF and IFH models have a rank deficiency of size one that will result in biased estimations, which means the better solvability of IC and IW models. The experiments are carried out based on the 7-day Global Positioning System (GPS) observations collected at 57 global Multi-GNSS Experiment (MGEX) stations and Global Ionosphere Map (GIM) products. The results indicate that the IW model can accelerate SF-PPP convergence and achieve higher positioning accuracy compared to the other three SF-PPP models, especially in kinematic mode. With convergence criteria of 0.25 m in horizontal and 0.5 m in vertical, the east/north/up convergence times of IW model are 0.5/15.0/25.0 min and 0.5/16.0/36.5 min for static and kinematic modes, respectively. The IW model is able to achieve an instantaneous positioning accuracy of 0.28/0.35/0.75 m. In addition, a real kinematic test also demonstrates the best positioning solutions of IW model. Regarding troposphere delay retrieval, the IF, IFH, and IW models obtain a comparable daily accuracy of 3.0 cm on average, while the IC model achieves the worst accuracy of 8.0 cm. For precise ionosphere delay estimation, IW model only needs an average initialization time of 34.3 min, but a longer initialization time of 51.6 min is required for IF model. The daily precision of ionosphere delay estimation for IW model can reach up to 10.8 cm. At the present accuracy of GIM products, it is suggested that the IW model should be adopted for SF-PPP first due to its superior performance in positioning and atmosphere delay retrieval.