Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

Coupling damage and reliability model of low-cycle fatigue and high energy impact based on the local stress–strain approach

Fatigue induced products generally bear fatigue loads accompanied by impact processes,which reduces their reliable life rapidly. This paper introduces a reliability assessment model based on a local stress–strain approach considering both low-cycle fatigue and high energy impact loads.Two coupling relationships between fatigue and impact are given with effects of an impact process on fatigue damage and effects of fatigue damage on impact performance. The analysis of the former modifies the fatigue parameters and the Manson–Coffin equation for fatigue life based on material theories. On the other hand, the latter proposes the coupling variables and the difference of fracture toughness caused by accumulative fatigue damage. To form an overall reliability model including both fatigue failure and impact failure, a competing risk model is developed. A case study of an actuator cylinder is given to validate this method.     

Friction moment analysis of space gyroscope bearing with ribbon cage under ultra-low oscillatory motion

This paper presents the model of calculating the total friction moment of space gyroscope ball bearings which usually work under ultra-low oscillatory motion and are very sensitive to the friction moment. The aim is to know the proportion of the friction moment caused by each frictional source in the bearing＇s total friction moment, which is helpful to optimize the bearing design to deduce the friction moment. In the model, the cage dynamic equations considering six degree-of-freedom and the balls dynamic equations considering two degree-of-freedom were solved.The good trends with different loads between the measured friction moments and computational results prove that the model under constant rate was validated. The computational results show that when the speed was set at 5 r/min, the bearing＇s maximum total friction moment when oscillation occurred was obviously larger than that occurred at a constant rate. At the onset of each oscillatory motion, the proportion of the friction moment caused by cage in the bearing＇s total friction moment was very high, and it increased with the increasing speed. The analyses of different cage thicknesses and different clearances between cage pocket and ball show that smaller thickness and clearance were preferred.     

带迎角钨杆斜侵彻铝板数值仿真研究

为研究迎角对钨杆斜侵过程的影响,开展了带迎角钨杆斜侵彻铝板数值仿真研究。仿真中采用SPH方法,Shock状态方程和Steinberg本构模型。钨杆共有两种尺寸,分别为Φ10mm×23mm和Φ10mm×46mm。铝板厚10mm,撞击速度为2km/s,撞击角度为60°。为简化分析,将迎角分解为俯仰角和偏航角,其中俯仰角范围为-90°～90°,偏航角范围为0°～90°。对钨杆侵彻过程的分析结果表明：斜侵彻存在临界迎角,在临界迎角范围内钨杆所受力矩可忽略不计;在临界迎角范围外,钨杆将发生弯曲甚至折断。对钨杆的剩余质量分析结果表明：当偏航角为0°且钨杆未折断时,剩余质量只在较小的范围内变化;当俯仰角为0°时,剩余质量随迎角增加线性减小。对钨杆的剩余速度分析结果表明：偏航角对剩余速度的影响与俯仰角对剩余速度的影响基本一致,剩余速度曲线关于0°迎角基本对称。根据仿真结果,采用曲线拟合的方法给出了钨杆斜侵彻铝板的剩余速度经验公式。     

激光加工气膜孔对定向凝固高温合金薄壁持久性能的影响

采用定向凝固无余量精铸工艺制造的接近于空心涡轮叶片形状和壁厚的管状薄壁（δ＝１．２ｍｍ）试样,研究了激光加工孔对定向凝固高温合金薄壁持久性能的影响。结果表明,在９００℃／３７０ＭＰａ下,与没有孔的薄壁试样相比,有一排孔的试样持久性能没有明显降低,有两排孔的试样持久寿命略有下降。显微分析表明,激光加工孔对组织没有明显的影响,只是稍微减小了承载面积,而且只有在出现两排激光孔时才有所表现。     

桨尖喷气驱动系统的实验与数值模拟研究

桨尖喷气驱动是一种很有应用前景的动力驱动类型,针对桨尖喷气驱动系统进行设计研究。通过建立压气机式桨尖喷气驱动系统的实验平台,改变入口条件,测量得到喷气管道内部的流动参数以及桨尖喷口的静推力,进而计算此驱动系统的输出功率,对整个驱动系统的性能进行试验分析,然后采用CFD数值模拟方法对试验的各个流动状态进行仿真计算。结果表明:CFD数值计算结果与试验值吻合的很好,随着入口总压的提高,推力及功率变大,同时说明了CFD数值方法的可靠性,也为CFD数值模拟技术在喷气驱动系统的效率以及动力来源的选择与适配研究提供了参考。     

用热流探针测量激波速度

激波速度测量是激波管和激波风洞运行状态的一个重要参数,压电传感器或光学方法测速系统成本高,而传统电离探针在激波马赫数较低、波后温度达不到空气电离程度的情况下无法满足实验要求。提出了一种使用同轴热电偶作为测速探针来测激波速度的方法,弥补了电离探针在激波马赫数较低时的不足。介绍了同轴热电偶探针测速原理,并设计了测量激波速度的系统电路。通过信号放大电路锁定激波冲激信号,触发脉冲信号发生电路,实现了一种单通道、多测点的激波风洞测速系统。分别开展以温度与热流为触发信号的风洞实验,结果表明只有使用热流信号才能满足激波测速的时间要求。     

复合材料夹层结构在航空领域的应用

详细描述了复合材料夹层结构及几种常用芯材的性能特点,综合分析了复合材料夹层结构在飞机上的应用案例,对各种夹层结构芯材成型工艺的重点、难点进行了探析,得到了复合材料夹层结构的性能概况及使用工艺要求,可为复合材料夹层结构设计、制造提供参考。     

重庆机床集团YD31125CNC6大型数控机床

日前,由重庆机床(集团)有限责任公司研制的用于风力发电行业大模数齿轮加工的YD31125CNC6大型数控滚齿机首次完成了大模数齿轮的加工试切,工件参数为模数m=20mm,齿数Z=25,齿宽B=140mm,外径D=540mm,一刀切加工精度达到了GB10095-2001IT7级,这表明为风力发电行业齿轮加工量身打造的大型全数控滚齿机的关键技术研制已取得成功.     

用于波音787的新型复合材料机翼除冰系统

在机械系统方面,现代商业飞机通常采用一系列管道从发动机内部引入加热的空气,通过加热空气在结冰机翼表面内侧的流动加热附近的机翼表面,从而达到除冰的目的。但是这不仅会使设计变得复杂,同时还会降低发动机的有效推力。所以,多年来研究人员一直在开发一种替代技术,即向机翼前缘表层里面置入导电元件来直接加热机翼表面,使冰层不会聚集变厚。