Study of GNSS-measured ionospheric total electron content variations generated by powerful HF-heating

The purpose of this work is to report the experimental evidences for the influence of perturbations in the electron density in the dayside mid-latitude ionosphere, that are caused by high-frequency heating of the F2 layer, on the GNSS signals. The experiments were carried out at the Sura heater (Radio Physical Research Institute, N. Novgorod). During the sessions of ionospheric heating with different time modulations of the radiated power the rays linking the navigational satellites with the ground receiver intersected the heated region. Variations in the total electron content (TEC) were studied; these variations are proportional to the reduced phases of navigational signals. It is shown that with the square-wave modulation of the radiated power (with periods of 1, 6, 10 and 15 min), perturbations with periods of the main modulation of heating and its harmonics appear in the spectrum of TEC variations. Examples are presented of identification of the heating-induced variations in TEC, including determination of the amplitudes and time characteristics of these variations.     

On Relationship of Flow Swirl Parameters and Gas-Dynamic Efficiency of Gas Turbine Engine Interturbine Transition Duct

The paper highlights significance of the interturbine transition duct as part of the high pressure and low pressure turbine spool. The correlations have been suggested allowing us to estimate variation of the average cross section flow swirl while its passing the interturbine transition duct.     

Approximate analytical solutions of stability problems for skew plates under combined loading

The known analytical solutions of the linearized stability problems for rectangular hinged plates under the combined loading are generalized to the similar problems for skew plates, the deformation mechanics of which is described by the equations of the classical theory formed in the oblique Cartesian coordinates.     

Experimental study of radial temperature gradient-reducing devices in GTE rotor disks

In this paper, we examine experimentally some devices the principle of action of which is based on using the dynamic pressure of air extracted to engine cooling and which are meant for reducing the radial temperature gradient in GTE rotor disks. We established that the devices equipped with the ejector channels make it possible to accelerate the process of the disk hub heating by hot air suction from the cavity periphery towards the rotor axis of rotation. Using the data of visualization studies, we show the possibility for efficient operation of ejector devices in the conditions of real GTE rotor circumferential velocities.     

Optimization of electrode system for the aircraft time-of-flight ion-marking airspeed and angle of attack sensor

A technique of optimizing the electrode system of the differential recorder for the aircraft time-of-flight ion-marking airspeed and aircraft angle of attack sensor by the criterion of ion-marking recording error variance minimum is considered. The technique is based on analyzing the function of spatial distribution for the ion-marking and recorder electrode interaction field potential and determining a point for which this function reaches the maximum slope. The relations making it possible to synthesize the sensor electrode system by the complex criterion as a ratio of error variance to transformation channel response are obtained.     

A lower bound estimate of the critical load for helicopter main rotor composite blade according to the limit equilibrium theory. The basic steps of an algorithm

The basic steps of an algorithm are given for calculating the parameters of the limiting state of a helicopter main rotor blade. To estimate the static strength, a technique of elastic constants variation is used; it is based on the limit equilibrium theory and enables us to obtain the upper and lower bounds for the critical load simultaneously. An iterative technique is proposed to determine the lower bound of the allowable load on the root section of the composite blade depending on the azimuthal angle of its turn in the helicopter hovering mode.     

Analysis of flow past oscillating cascades by the implicit method to evaluate the cascade aeroelastic stability in viscous flow

A technique of analyzing the flutter initiation in flat plate compressor cascades was developed. The viscous and inviscid flow study was carried out using the COBRA solver based on the modified implicit Godunov method and unsteady implicit method updated for using. The flutter conditions were revealed and the effect of taking into account viscosity, angles of attack and time steps was investigated.     

Determination of the influence of a clearance between the case and blade ends of the semi-open impeller on the centrifugal compressor stage characteristics

The influence of the clearance between the case and blade ends of the semi-open impeller on the centrifugal stage characteristics is considered using the experimental data and numerical calculation results.     

Influence of geometry and operating conditions of a centrifugal compressor stage on the radial gas force

The influence of geometry and operating conditions of the centrifugal compressor stage on the radial gas force is determined on the basis of the theoretical method and calculation program using experimental boundary conditions.     

Application of high-order accurate methods to solve the computational gas dynamics and aeroacoustics problems

The application of the low dissipative high-order accurate scheme for numerical solution of the Euler and Navier-Stokes equations in the two-dimensional statement is considered. The scheme of calculating space derivatives is the seven-point central-difference approximation of the fourth order with the coefficients optimized to reduce the dispersion errors. The optimized six-step Runge-Kutta method is used for evaluating the time derivatives. By means of filtration, spurious pulsations are suppressed and shocks are processed. The results of verifying the calculation scheme realized on the stationary problem of flow around the model turbine blades are presented.