温度场对航空发动机转子超转破裂的影响

CCAR33.27超转适航要求,分析和试验确定的超转转速,必须基于温度和温度梯度的最不利组合。因此,研究温度和温度梯度对超转破裂的影响有非常重要的意义。以某型航空发动机低压6级涡轮转子为例,采用极限应变方法开展了转子部件的超转破裂分析,对比了常温和高温（红线转速对应的温度分布）下转子关键轮盘应变分布趋势和应变增长规律、预测的超转破裂的起始位置和破裂转速等轮盘超转特性;针对超转破裂分析,提出了在高温条件下,经过常温超转破裂试验验证的方法应用的有效性条件。低压涡轮转子的分析结果也显示,红线转速对应的温度状态下,轮盘超转破裂转速比常温下显著降低,而高温下材料屈服强度的大幅降低则是破裂转速下降的主要原因。     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

Heading control strategy assessment for coaxial compound helicopters

The coaxial compound helicopter has two possible strategies for heading control: collective differential and rudder deflection. A flight dynamics model is developed to assess the effect of different heading control strategies. This includes the trim characteristics, steady flight performance,controllability, and manoeuvrability. The trim study demonstrates that heading control strategies are less influential on trim results, and the steady flight performance is also not significantly affected by the heading control strategy adopted. The controllability analysis shows although heading bandwidth and phase delay results at various speeds with different heading control strategies are all satisfied, the control derivative of the collective differential decreases as speed increases, and its heading aggressive agility is degraded into Level 3 in high-speed flight. In addition, using collective differential would lead to severe heading-rolling coupling as forward speed increases. On the contrary, the control derivative and aggressive agility of the rudder deflection is improved with forward speed, and there is no evidence of heading-rolling coupling. Finally, the transient turn MissionTask-Element(MTE) is utilized to investigate the heading manoeuvre characteristics in different heading control strategies, which indicates that the collective differential would add the amplitude of control input and the power consumption during this MTE.     

300 MVA脉冲发电机组滑差方式起动过程研究

介绍了300 MVA脉冲发电机组的滑差装置。对机组采取滑差方式的起动过程进行了分析和等效建模。根据机组实际起动过程电气波形,利用非线性规划模型,建立了滑差装置液体电阻等效仿真模型,并代入机组参数对起动过程进行仿真,仿真结果和实际波形吻合,验证了模型的正确性。在此基础上,为了使机组的转速达到额定转速,提出在滑差装置液体电阻低位时并入两级固体金属电阻后短接的方案,给出了两级固体金属电阻的阻值等理论参数,并通过仿真验证了方案的可行性。建立的仿真模型可以作为研究不同参数、不同控制策略下的机组起动过程动态特性的重要工具。     

基于里德堡原子相干效应的微波电场测量技术研究进展

近年来,采用里德堡原子的微波电场测量技术得到了迅速发展,获得了广泛应用。该电场探测技术是一项全新技术,可以将微波电场通过基本物理常数与频率测量直接关联,具有测量动态范围大、测量灵敏度高和测量不确定度小的特点,有望替代传统溯源路径,直接关联国际单位制（SI）。本文基于里德堡原子相干效应的微波电场测量技术原理,针对国内外微波电场的高准确度、高灵敏度和极化方向测量技术发展现状,和对微波电场测量的工程化光源系统,蒸气室探头的仿真验证实验和集成式蒸气室探头的设计研究等方面的相关进展做了详细介绍。     

用于EMI测量接收机脉冲响应校准的标准脉冲信号产生方法

EMI测量接收机作为电磁兼容测试中的关键仪器应用越来越广泛,但目前该类仪器的脉冲响应校准所用的标准源完全依赖于进口,国内尚无可替代的标准脉冲信号产生器。介绍一种用于EMI测量接收机脉冲响应校准的标准脉冲信号产生方法,首先建立标准脉冲信号的参数模型并对其进行数值分析和仿真,验证其符合CISPR 16-1-1标准的要求,之后搭建实验系统,利用标准脉冲信号生成软件控制任意脉冲信号发生器输出标准脉冲信号并对其进行补偿修正,获得符合CISPR 16-1-1标准要求的标准脉冲信号,该信号可用于EMI测量接收机脉冲响应的校准。     

考虑喷油润滑的附件机匣温度场分析

附件机匣作为航空发动机重要部件之一,其产热和散热的问题比较复杂.针对以往附件机匣相关研究只关注固体域的产热、散热分析,而对滑油散热作用不能充分考虑这一问题的现状,提出了基于流体仿真思想的稳态温度场分析方法.首先,通过分析附件机匣产热、散热问题的基本规律和特点,进一步采用k-ε湍流模型来模拟机匣内的情况,多相流模型模拟滑油,并且使用多参考坐标系模拟滑油在运动过程中的换热.最后,以某附件机匣作为具体应用案例,验证了方法的正确性和可行性,从而形成了一套行之有效的使用FLUENT软件对附件机匣进行稳态温度场仿真分析的模型和方法.研究的成果对于后续附件机匣的可靠性与寿命分析有重要支撑作用.      

飞机发动机叶片缺陷的差激励涡流传感器检测

针对某型号飞机发动机涡轮叶片上预制的微裂纹缺陷进行了检测研究.基于涡流检测技术设计并研制了一种尺寸小、灵敏度高的差激励探头,应用有限元分析软件开展了叶片微裂纹缺陷仿真分析.为了实现叶片的自动高效检测,设计并采用数控多自由度扫查台来控制采集过程,实现了对叶片表面裂纹缺陷的快速扫查检测.采集信号经过信号调理电路,A/D转换后输入计算机,完成信号的保存、处理和输出.通过对比实验结果与仿真结果发现,研制的差激励式涡流传感器可以有效地实现对叶片类零件表面微裂纹位置的判定,对涡轮叶片类零件微缺陷早期诊断评估具有一定的现实和借鉴意义.      

非合作目标拖拉式对接机构设计与分析

针对非合作目标对接技术的要求和特点,提出了一种以卫星远地点喷管为对接接口的非合作目标拖拉式对接机构方案。设计了拖拉式对接机构的具体结构并建立其三维CAD模型,根据此模型,对机构进行了包络范围的求解;使用ADAMS软件对机构进行了动力学仿真,分析了对接过程中目标星与机械臂的动态特性,分析了对接过程中捕获力与关节受力情况。计算与仿真结果表明,提出的对接机构能够对目标进行有效、可靠的对接捕获,碰撞接触力小于280N,不会造成本体及目标的破坏。与以往对接机构相比,此拖拉式对接机构具有结构简单、可靠性高、捕获范围大、控制方法简单等优点,且机构受力合理,适合作为空间非合作目标对接的捕获装置。     

航空电子设备NSEE试验评价方法

本文定义了航空电子设备大气中子单粒子效应(NSEE)硬失效、硬错误与软错误等大气中子辐射可靠性表征参数,提出了一套航空电子设备抗大气中子单粒子效应危害能力的试验评价方法,包括试验应力终止条件与起始条件的确定方法、M_NSEE预估方法、试验程序、试验评价方法等,并通过某航空用卫星导航接收机试验案例证明了该方法在工程应用中的可操作性与有效性,通过掌握数字信号处理(DSP)、静态随机存储器(SRAM)、现场可编程门阵列(FPGA)的NSEE敏感特性,可为航空用卫星导航接收机NSEE危害防控提供针对性的技术支持.本文为我国航空电子产品大气中子单粒子效应试验评价奠定了理论与应用基础,同时也为其他电子信息产品在大气中子单粒子效应试验评价方面提供了重要依据和参考.