我国地方行政立法质量评价——以河南省为例

地方行政立法的质量状况,直接影响着国家法律的实施和地方性事务的管理成效。通过对2000～2010年的河南省政府规章及其制定活动的综合评价,认为地方行政立法程序、手段和技术比较完善,规章质量状况良好,但存在计划约束力不强,公众参与度不高,立法技术相对落后等问题,地方行政立法质量有进一步提升空间。     

基于PC/104的某飞机任务电源监控系统设计与实现

某飞机任务电源系统需要监控系统以保障飞行任务的供电安全.为提高其监控系统的可靠性和可维护性,完成了基于PC/104和远程数据采集模块的某飞机电源监控系统的设计与实现.该系统运用结合RS-485进行多串口通信,将采集的数据返回给监控界面,实现对远程终端的监控,以图形化编程软件LabVIEW为平台完成了采集与监控各部分的软件设计,并通过了各项测试,具有很好的稳定性和安全性,实现了对电源系统的监控、报警和保护.     

TC11焊接接头高周疲劳分形损伤模型

根据金属疲劳断口具有几何分形特征,将Chaboche高周疲劳损伤模型推广到分数维空间,建立了综合考虑断口细观特征的高周疲劳分形损伤演化模型.针对TC11钛合金电子束焊接接头,以载荷控制的疲劳试验为基础研究其高周疲劳性能;采用扫描电镜法(SEM)对断口微观特征进行定量分析,计算得到了各级载荷下疲劳断口的分形维数;通过对试...     

多场耦合计算平台与高超声速热防护结构传热问题研究

从有限元法(FEM)和有限体积法(FVM)的单元特性出发,提出一种具有局部守恒特性的界面载荷插值方法.采用共享内存技术开发适用于通用有限元和计算流体力学(CFD)软件的多场耦合计算平台,并基于分区耦合方式实现流固耦合传热计算.作为验证,分别将ANSYS与Fluent和CFD-FASTRAN软件进行耦合,计算外壁冷却的喷...     

多功能实验室环境条件保障装置的设计

介绍了维持计量检定工作环境条件保障装置的设计方法，该装置可实现实验室温，湿度的测量与控制，有方便的通讯接口便于与计算机连接，并附加有多点时间控制电路以实现提前预热仪器设备提高工作效率的功能。     

Fault self-repair strategy based on evolvable hardware and reparation balance technology

In the face of harsh natural environment applications such as earth-orbiting and deep space satellites, underwater sea vehicles, strong electromagnetic interference and temperature stress,the circuits faults appear easily. Circuit faults will inevitably lead to serious losses of availability or impeded mission success without self-repair over the mission duration. Traditional fault-repair methods based on redundant fault-tolerant technique are straightforward to implement, yet their area, power and weight cost can be excessive. Moreover they utilize all plug-in or component level circuits to realize redundant backup, such that their applicability is limited. Hence, a novel selfrepair technology based on evolvable hardware（EHW） and reparation balance technology（RBT） is proposed. Its cost is low, and fault self-repair of various circuits and devices can be realized through dynamic configuration. Making full use of the fault signals, correcting circuit can be found through EHW technique to realize the balance and compensation of the fault output-signals. In this paper, the self-repair model was analyzed which based on EHW and RBT technique, the specific self-repair strategy was studied, the corresponding self-repair circuit fault system was designed, and the typical faults were simulated and analyzed which combined with the actual electronic devices. Simulation results demonstrated that the proposed fault self-repair strategy was feasible. Compared to traditional techniques, fault self-repair based on EHW consumes fewer hardware resources, and the scope of fault self-repair was expanded significantly.     

人员密集场所玻璃材料装修消防安全隐患与防治措施探讨

吸取近年来人员密集场所重特大火灾事故及灭火救援伤亡案例教训,阐述了进一步完善此类场所消防安全防范措施的必要性和重要性.对人员密集场所目前装修工程中常使用的玻璃材料类型、功能及其安装工艺进行了说明.针对目前现行消防技术标准并结合工作实际,对玻璃材料装修在材料防火性能、安全疏散逃生、应急灭火救援和增加火灾负荷等方面存在的消防安全隐患进行了分析和探讨,并提出了切实可行的解决方案,为有关消防技术标准规范的修订提供了参考.     

某航天器输氢管道系统结构完整性评估

为保障某航天器在服役年限内不发生事故,针对航天器上采用插入焊接技术的精密管道系统进行结构完整性评估。在考虑到系统存在整圈的环形未焊透缺陷基础上,结合工程实践,假设在焊接区域存在更危险的平面缺陷。首先,开展高压气相热充氢试验下的标准拉伸和三点弯试验得到管道系统材料"J-75"在临氢环境下应力应变曲线和断裂韧性。其次,采用有限元程序计算系统在内压、惯性载荷与离面位移作用下的应力分布,考虑到间隙配合中的不确定性,改变模型中的最大间隙多次模拟计算,发现最大应力位置基本不变,以此区域作为假想缺陷的具体萌生区域。最后,采用失效评估图（FAD）方法对存在4种缺陷模式的系统分别进行结构完整性评估。通过引入安全裕度的概念,发现系统在含有初始尺寸（0.15 mm）的4种平面缺陷时,均处于安全状态,并且安全裕度都在2倍以上;通过工程临界分析（ECA）发现随着缺陷尺寸的增大,系统中含有缺陷2（位于管道焊接区域最大应力处的轴对称平面且沿焊深方向扩展的缺陷）时最为危险,且当缺陷深度超过0.61 mm时将断裂失效;考虑到测试数据的弥散性,针对系统最危险的模式,以安全裕度为可靠性指标,将失效评估图方法与可靠性评价相结合,得到系统在含有尺寸为0.15 mm的缺陷2情况下保有足够安全裕度的可靠性下限值超过0.999 5。     

Parametric Modeling of Circuit Model for AC Glow Discharge in Air

In the parametric modeling of the circuit model for glow discharge in air,a new method for the design of glow discharge circuit model is presented.The new circuit model is an important reference for the design of plasma power supply,the simulation of glow discharge plasma actuator and the simulation of glow discharge plasma anemometer.The modeling approach consists in developing an electrical model of the glow discharge in air based on circuit components.The structure of the circuit model is established according to the theoretical analysis and the experimental device.Then the parameters of the circuit model are obtained based on the circuit analysis.Finally,the circuit model is verified by comparing the simulation current with the experimental current.This model takes into account the whole framework of the air glow discharge including the sheath and the plasma area.The built circuit model is feasible and reliable,thus being instructive for the investigation of the glow discharge in air.     

低温辐射计吸收腔研制

针对高灵敏度低温辐射计研制需求,提出一种低温辐射计吸收腔.设计椭球面光阑的多次反射结构,同时采用扩散焊工艺,进而实现了椭球面光阑、斜口—斜底圆柱腔和斜底面三部分的焊接成形,以此形成有效光陷阱,使入射到吸收腔中的辐射被近似完全吸收.制备具备多孔结构的碳纳米管涂层,采用喷涂为主的工艺实现腔体内壁涂层的均匀性分布.基于积分球...