螺栓挤压推力终止系统验证试验

本文总结了螺栓挤压推力终止系统(BETTS)的设计、研制和验证试验。该系统在阿诺德工程研制中心(AEDC)进行了多次冷试,一次海平面热试和两次高空点火推力终止试验,试验所用的发动机是政府向化学系统分公司提供的“民兵”发动机空壳体装药后制成的。通过大发动机热试,证明本计划所验证的这种BETTS可以消除前部碎片,大大地简化药柱和发动机壳体的设计,提高末级性能。另外,这种方法设计简单,从而可以降低推进系统的成本。BETTS用爆炸螺栓和挤压螺栓的组合代替连接喷管法兰和发动机壳体法兰的普通螺栓。接到指令后,爆炸螺栓立即打开,喷管循着挤压螺栓向后平移,发动机气体迅速排出,从而使推进剂熄火。挤压螺栓控制着喷管的移动速度和最大运动行程。以前根据NO.F04611—75—C—0044合同(CSD计划2549)曾成功地在缩比发动机上进行了BETTS热试和在飞行重量的“民兵”Ⅲ第三级发动机上进行了冷试。     

HTPB推进剂的老化及使用寿命

为了进行老化评价研究,选择和研制了三种不同固体含量的(88～91%)端羟基聚丁二烯(HTPB)推进剂。已经证实,88%固体含量的HTPB推进剂符合以前提出的老化模型。这种老化模型已成功地进一步用于较高固体含量的推进剂以及其它计划用的HTPB推进剂的实测力学性能老化数据。采用这种老化模型,根据加速热老化试验数据予测了长期力学性能,予测数据与六年实测老化数据相当一致。利用予测的推进剂破坏性能,结合火箭发动机的要求,来确定予先选定安全裕度的发动机药柱的使用寿命。本文列出了各种复合推进剂老化速率的比较数据。根据老化结果的分析,提出了一个宽范围老化行为的数学表达式。     

1980年固体火箭技术的成就

虽然美航宇局的航天飞机一再推迟发射日期,而赛奥科尔公司研制的固体火箭助推器(SRB)仍取得了明显的进展。1980年2月第三台即最后一台鉴定发动机进行了静态试车。航天飞机初次飞行用的第一段发动机在9月26日运到肯尼迪空间中心。赛奥科尔公司已完成了第二次飞行用的发动机和喷管出口锥的生产工作,第三次飞行用的发动机将于80年底生产出来。     

"Signal" search for intelligence in the galactic nucleus with the array of the Lowlands

In August, 1981, the Westerbork Synthesis Radio Telescope was used for 4 h to search for narrowband pulsing radio beacons in the direction of the Galactic Center. By using both the spatial discrimination and temporal stability available to an interferometric measurement, weak intermittent signals can be detected even in the face of the strong, naturally caused radiation from this region. A radio beacon within our bandwidth, centered on the 21 cm neutral hydrogen line, would be recognizable if it had a repetition period between 40 sec and 1/2 h. The rms sensitivity to point sources was approximately 50 mJy/cycle, and the detection limit was 500 mJy/cycle. The limit degrades for pulse widths < 0.02s. No repetitive signals were found. For a swept, narrow-band radio beacon constrained to the Galactic Disk (beamwidth = 0.02 rad), our detection limit corresponds to a transmitter power of 10(11) MW at the Galactic Center.     

Effect of microgravity on Escherichia coli and MS-2 bacteriophage disinfection by iodinated resins

Experiments on chemical disinfection by iodinated resins were conducted on STS 50 (USML-1), which flew a 13 day mission during 1992. Fluid processing apparatus containing microorganisms and iodinated resins was assembled in either Manhattan, Kansas, or Boulder, Colorado, and loaded on-board the Space Shuttle for the mission. Pentaiodide resin was more effective than the triiodide resin against Escherichia coli. Both resins were more effective bactericides at unit gravity than microgravity because of cosedimentation of bacteria and iodinated resin beads. In bacteriophage experiments, the triiodide resin reduced the viable titer of MS-2 by nine logs. The few viable phage surviving chemical disinfection were associated with precipitant formation in the fluid processing apparatus.     

The effect of head-down tilt on brain potentials related to visual attention

To study the possible effect of simulated weightlessness on brain function state, the brain event-related potentials (ERPs) in a simple visual selective response task were compared between HDT and HUT in 9 normal subjects. The results were: The Target(T) and non-Target(NT) flash signals both induced significant slow positive potentials which were supposed to related to the attention state; the amplitude of the positive potentials in frontal regions decreased significantly especially for NT-ERPs during HDT comprared with that during HUT. The data reported provide new evidence indicating that more attention should be paid on the brain function study during space flight.     

铸造高温合金熔炼工艺中的冶金原则

文中介绍了苏联铸造高温合金工艺中冶金原则的发展。除去合金化元素之外,杂质元素和微量添加元素是决定合金组织和性能的最重要因素之一。文中详细讨论了在不同条件下它们对合金高温性能的影响。结论中提出改进铸造高温合金冶炼工艺的若干有效的措施。     

绿色制造中的干切削技术

冷却润滑液的存储、使用以及废弃处理需要专门的物流系统,因而费用很高;冷却润滑液处理不当会对人的健康以及环境造成危害;工件经过湿加工后必须进行清洁处理,这都费时费力,同时增加了对系统的要求.基于上述原因,近年来干切削技术受到广泛关注.