Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

Performance evaluation for MAP state estimate fusion

This paper presents a quantitative performance evaluation method for the maximum a posteriori (MAP) state estimate fusion algorithm. Under ideal conditions where data association is assumed to be perfect, it has been shown that the MAP or best linear unbiased estimate (BLUE) fusion formula provides the best linear minimum mean squared estimate (LMMSE) given local estimates under the linear Gaussian assumption for a static system. However, for a dynamic system where fusion is recursively performed by the fusion center on local estimates generated from local measurements, it is not obvious how the MAP algorithm will perform. In the past, several performance evaluation methods have been proposed for various fusion algorithms, including simple convex combination, cross-covariance combination, information matrix, and MAP fusion. However, not much has been done to quantify the steady state behavior of these fusion methods for a dynamic system. The goal of this work is to present analytical fusion performance results for MAP state estimate fusion without extensive Monte Carlo simulations, using an approach developed for steady state performance evaluation for track fusion. Two different communication strategies are considered: fusion with and without feedback to the sensors. Analytic curves for the steady state performance of the fusion algorithm for various communication patterns are presented under different operating conditions.     

高燃速丁羟推进剂配方研究

通过多种途径的试验,对高燃速丁羟推进剂配方进行了研究.试验结果表明,采用超细防结块氧化剂和液固组合燃速催化剂能使推进剂的燃速达到70mm/s以上(在6.864Mpa压强下);采用组合工艺助剂可改善推进剂工艺性能.本推进剂燃烧稳定,压强指数和温度敏感系数较低,力学性能良好,为高燃速推进剂的研制奠定了良好的基础.     

H∞控制及其应用

本文叙述了Ｈ∞控制器设计的频域法和代数法，在频哉法中介绍了标准问题的模型匹配解法和丁谱分解法；在代数法中介绍了多项式法，直接状态空间法，最后简述了几个实际应用的例子。     

C尺寸ⅤⅪbus主机箱的研制

介绍ⅤⅪｂｕｓ的关键部件──Ｃ尺寸主机箱样机的性能指标、研制主机箱的关键技术和所采取的措施。该主机箱已在某导弹仿真系统中应用。使用表明，功能正常、参数和仿真性能全部符合研制任务书的要求     

中山植物园植物定植图微机显示与管理系统

首先指出利用微机管理植物园取代落后的手工管理的意义。进而介绍了植物定植图微机显示与管理系统的具体实现途径，并描述了能将地图（含充色地图）、植物、宇符等录入。绘出，以及对植物进行检索显示等主要功能。     

正态分布可靠寿命经典近似限的改进

本文给出了正态分布可靠寿命的又一个经典近似下限，经验证，本文所给出的结果的精度比已有的结果精度要高，可提供给可靠性工程人员使用。     

刀刃法在轨MTF测量性能分析

文章主要研究采用刀刃法测量在轨遥感器的MTF。刀刃法MTF测量准确程度如何，需要有一个定量的客观的评价，文章用仿真的方法对MTF测量精度进行了检验，对于噪声对MTF的影响进行了研究。     

GPS空间分集接收机

为解决传统单天线GPS接收机在载体旋转情况下不能连续跟踪卫星连续定位和速度偏差较大的问题,提出一种GPS空间分集接收机设计方案。该接收机采用空间分集算法和消旋解算方法,能稳定连续地跟踪GPS卫星信号,并准确地求解出载体的平动速度。     

运用数学方法模拟推进剂贮箱增压

本文介绍了运用数学方法模拟推进剂贮箱内的增压、传热和传质的物理热动力过程.增压系统的目的是控制推进剂贮箱内的气体空间(也称为"气垫空间")压力和进入发动机的推进剂质量流量.用数学模拟来预测气垫和推进剂的状态以保证贮箱内的压力和温度值保持在认可的限度内,即使离开贮箱的推进剂压力满足发动机泵入口的净吸程要求.