Up-to-date observations of space energetic particles made by the Chinese satellite Fengyun-1 (B).

This paper presents the observational results of space energetic particles obtained by the Cosmic Ray Composition Monitor (CRCM) onboard the Chinese satellite, Fengyun-1(B). These results, including those of a few solar proton events, the geomagnetically trapped particles and the anomalous cosmic ray components, were obtained from 3 September 1990 to 15 February 1991. The observed elements include H, He, C, N, O and Fe of energies from 4-23 MeV/u. It was found that the proton fluxes of the inner Radiation Belt (IRB) increased obviously during the period of solar proton event (SPE). A few kinds of heavy ions (Z > or = 6) were also detected in the IRB. As to the anomalous cosmic ray component (ACRC), in addition to C, N and O, anomalous iron particles were also recorded.     

Cyclic Oxidation Behavior of an EB-PVD CoCrAlY Coating Influenced by Substrate/coating Interdiffusion

To reveal the influence of substrate/coating interdiffusion on the cyclic oxidation property of a metallic coating, cyclic oxidation behavior of an EB-PVD CoCrAlY coating on directionally solidified Ni-based superalloy DZ125 at 1 050 oC is investigated. The 40 μm thick CoCrAlY coating has a cyclic oxidation life of around 160 h, and the oxidation constant is 1.915× 10.7 mg4·cm.8·s.1. However, severe spallation of the oxides containing Co, Cr, Ni, Ta and Ti occurs with longer cyclic oxidation. The degradation in oxidation resistance for the coating is related to the depletion of Al due to the oxide spallation and interdiffusion. Severe interdiffusion between the coating and underlying substrate occurs at 1 050 oC. The composition of the substrate has an important effect on the thermal cycling lifetime of the coating. The influencing mechanism is discussed.     

InvesInvestigation of the Effects of Airfoil-probes on the Aerodynamic Performance of an Axial Compressor

In order to investigate the effects of the airfoil-probes on the aerodynamic performance of an axial compressor,a numerical simulation of 3D flow field is performed in a 1.5-stage axial compressor with airfoil-probes installed at the stator leading-edge(LE).The airfoil-probes have a negative influence on the compressor aerodynamic performance at all operating points.A streamwise vortex is induced by the airfoil-probe along both sides of the blade.At the mid-operating point,the vortex is notable along the pressure side and is relatively small along the suction side(SS).At the near-stall point,the vortex is slightly suppressed in the pressure surface(PS),but becomes remarkable in the suction side.A small local-separation is induced by the interactions between the vortex and the end-wall boundary layer in the corner region near the hub.That the positive pitch angle of the airfoil-probe at 6.5% span is about 15° plays an important role in the vortex evolution near the hub,which causes the fact that the airfoil-probe near the hub has the largest effects among the four airfoil-probes.In order to get a further understanding of the vortex evolution in the stator in the numerical simulation,a flow visualization experiment in a water tunnel is performed.The flow visualization results give a deep insight into the evolution of the vortex induced by the airfoil-probe.     

基于原位拉伸测定GTN损伤模型参数的5052铝合金成形极限应力图研究(英文)

传统成形极限图(FLD)由第一主应变与第二主应变的比值构成。但FLD依赖于成形历史和应变路径。因此,本文采用成形极限应力图(FLSD)来预测铝合金5052-O1(AA5052-O1)的成形极限。将修订的Gurson-Tvergaard-Needleman(GTN)塑性势模型用来模拟Nakazima凸模胀形实验。采用带扫描电镜(SEM)的原位拉伸试验观察记录损伤演化过程以确定GTN模型中的材料参数。通过计算AA5052-O1三个损伤阶段的孔洞分数获得GTN模型参数。根据实验结果,原生孔洞体积分数、最大形核孔洞体积分数、临界孔洞体积分数,最终断裂孔洞体积分数分别为0.002918,0.0249,0.030103,0.04854。在断裂前最后一个载荷步获得的应力应变值用来绘制AA5052-O1的FLSD和FLD。与Nakazima凸模胀形试验和单轴拉伸试验结果相比较,预测结果与试验结果较为吻合。由原位拉伸试验确定的模型参数可用于研究韧性金属的成形极限。     

Theory of Economic Life Prediction and Reliability Assessment of Aircraft Structures

The theory of economic life prediction and reliability assessment of aircraft structures has a significant effect on safety of air-craft structures.It is based on the two-stage theory of fatigue process and can guarantee the safety and reliability of structures.According to the fatigue damage process,the fatigue scatter factors of crack initiation stage and crack propagation stage are given respectively.At the same time,mathematical models of fatigue life prediction are presented by utilizing the fatigue scatter factors and full scale test results of aircraft structures.Furthermore,the economic life model is put forward.The model is of sig-nificant scientific value for products to provide longer economic life,higher reliability and lower cost.The theory of economic life prediction and reliability assessment of aircraft structures has been successfully applied to determining and extending the structural life for thousands of airplanes.     

星载双频GPS相位历元差缩减动力学定轨(英文)

研究了星载双频GPS相位历元差缩减动力学定轨方法,该方法既克服了相位历元差运动学方法在观测几何较差或数据不足情况下无法应用的缺点,又避免了相位非差动力学方法易受周跳和模糊度影响的缺点。历元差方法对相位周跳的影响不敏感,因此能够降低相位数据预处理中周跳探测的难度。在模型求解过程中,解决了高维矩阵的计算问题,将长弧段观测数据分成若干短弧段,相邻两个短弧段的连接处不做差分,仅在每个短弧段内部进行历元间差分处理。通过对GRACE卫星进行试算,并与GFZ事后科学轨道进行比较,结果表明相位历元差缩减动力学定轨精度在径向、沿迹方向和轨道法向分别可达1.92cm、3.83cm和3.80cm,三维位置精度可达5.76cm,该方法与相位非差缩减动力学定轨精度相当。     

Effect of Stitching on Plain and Open-hole Strength of CFRP Laminates

 Experimental and analytical investigation is conducted to explore the effects of stitching on plain (without hole) and open-hole compressive and tensile strength of uniweave T300/QY9512 laminates under different environmental conditions (20 篊/dry and wet, 150 篊/dry and wet). Strength performance of stitched composite laminates is also studied using finite element analysis (FEA) model and compared with the experimental results to validate the model. It is found that under similar environmental conditions, the open-hole compressive strength of stitched laminate is decreased and open-hole tensile strength increased as compared to the unstitched laminates. Predicted tensile and compressive strengths are found to be in a good agreement with the test results and the relative error in all cases is less than 15%.     

纳米压痕实验微米级深度硬度下降现象的研究(英文)

本文针对均匀材料微米级压痕深度,分析接触深度、接触面积、载荷以及加载时间几种因素对实验数据的影响,结合有限元数值模拟,说明压头几何缺陷、接触深度与接触面积的处理并不是造成微米级压痕硬度随压深增大而下降的主要原因,最可能的原因是材料的蠕变特性。进行了不同最大压深实验显示连续刚度法(CSM)将强化蠕变特性对硬度曲线的影响,证明造成该现象的重要原因是纳米压痕实验的实验方法问题。     

形貌和空间对PAEK增韧BMI树脂及其碳纤维复合材料层压板韧性和冲击损伤阻抗的影响(英文)

通过对热塑性树脂PAEK增韧BMI树脂的玻璃化转变行为,相形貌和断裂韧性,以及对采用"离位"概念增韧的T700/BMI复合材料的层间形貌及其冲击后压缩强度(CAI)的分析,研究了微结构-性能之间的关系,发现特征相分离形貌随着PAEK的含量而变化。特别探索了PAEK-BMI复相体系的相形貌与断裂韧性之间的关系,得到的断裂机理解释了复合材料层压板的分层和冲击损伤行为。有关"离位"增韧的机理、以及扩散控制的相行为等还需要继续研究。     

Static Pull and Push Bending Properties of RTM-made TWF Composite Tee-joints

This paper deals with static pull and push bending tests on two-dimensional (2D) orthogonal EW220/5284 twill weave fabric (TWF) composite tee-joints processed with the resin transfer moulding (RTM) technique. Static pull and push bending properties are determined and failure initiation mechanism is deduced from experimental observations. The experiments show that the failure initiation load, on average, is greater for push bending than for pull bending, whereas the scatter is smaller for push bending than for pull bending. The failure mode of RTM-made tee-joints in pull bending tests can be reckoned to be characteristic of debonding of resin matrix at the interface between the triangular resin-rich zone and the curved web of tee-joint until complete separation of the curved web from the bottom plate. In contrast, as distinct from the products subject to pull bending loading, the RTM tee-joints in push bending tests experience matrix cracking and fibre fracture from outer layers to inner layers of the bottom plate until catastrophic collapse resulting from the bending. Three-dimensional finite element (FE) models are presented to simulate the load transfer path and failure initiation mechanism of RTM-made TWF composite tee-joint based on the maximum stress criterion. Good correlation between experimental and numerical results is achieved.