计及壁面传热的微型向心涡轮气动设计探讨

毫米级微型向心涡轮传热效应显著区别于常规向心涡轮,发展计及壁面传热效应的微型向心涡轮的气动设计方法对微型燃气轮机的设计具有重要意义.根据微型向心涡轮壁面非绝热的特点,通过理论分析,初步建立了计及固壁传热效应的微型向心涡轮速度三角形的分析模型.在此基础上发展了计及传热效应的微型向心涡轮的气动设计方法.分析得到了考虑传热影响的微型向心涡轮设计规律.利用三维数值模拟手段对模型和设计方法进行了验证.结果初步表明所发展计及壁面传热效应的模型和微型向心涡轮气动设计方法具有较好的可行性.     

Scientific objectives and payloads of Tianwen-1, China’s first Mars exploration mission

This paper describes the scientific objectives and payloads of Tianwen-1, China’s first exploration mission to Mars. An orbiter, carrying a lander and a rover, lifted-off in July 2020 for a journey to Mars where it should arrive in February 2021. A suite of 13 scientific payloads, for in-situ and remote sensing, autonomously commanded by integrated payload controllers and mounted on the orbiter and the rover will study the magnetosphere and ionosphere of Mars and the relation with the solar wind, the atmosphere, surface and subsurface of the planet, looking at the topography, composition and structure and in particular for subsurface ice. The mission will also investigate Mars climate history. It is expected that Tianwen-1 will contribute significantly to advance our scientific knowledge of Mars.     

焊后热处理对高温运行10CrMo910钢管接头持久寿命的影响

本文通过１０ＣｒＭｏ９１０钢大口径厚壁管道高温模拟试验证实，焊后热处理是一个短时超高温运行过程，它使１０ＣｒＭｏ９１０钢管接头组织提前老化，显著降低了接头的持久寿命。试验结果表明，传统的焊后热处理工序应当取消。     

利用均匀抽吸地板进行高速列车模型地板边界层影响的试验研究

在KD－03低速风洞中研制了一种边界层可人为控制的均匀抽吸地板。研究了在各种来流速度下均匀抽吸地板上边界层与抽吸系数的关系。在该地板上对高速列车模型气动力与地板边界层的关系进行了实验研究。对实验的几种模型状态，边界层吸除使列车模型所受阻力、负向升力和低头力矩均有明显增加，其增量与模型底部形状有关；在有侧滑角时，边界层吸除对模型气动力的六个分量均有影响。在没有边界层控制的固定地板上进行高速列车模型风洞实验，会使实验结果固边界层的影响而产生较大偏差。利用均匀抽吸地板可有效地消除边界层的影响，从而较准确地模拟地面效应的影响，提高高速列车模型风洞实验气动载荷的实验精度。而且，它的实验结果可为没有地板边界层控制装置的风洞中同类模型实验的边界层修正提供参考依据。     

基于双磁钢转子的大力矩飞轮用电机设计

针对卫星快速敏捷和大角度机动的需求,设计了一种基于双磁钢转子的大力矩飞轮用永磁电机。介绍了大力矩飞轮用电机的工作原理和结构构成,给出了主要尺寸的设计准则,并在Maxwell 环境下对双磁钢转子的永磁直流电动机进行了有限元分析。     

红外动态目标模拟器光学系统的设计

设计了一种用于红外导引头性能测试的红外动态目标模拟器,利用数字微镜阵列(DMD)对黑体红外辐射进行反射调制,并由光学准直系统实现红外场景生成系统与红外导引头的光学耦合。用光学设计软件（ZEMAX）对准直光学系统进行了设计和优化,准直光学系统成像质量良好,接近衍射极限,点列图直径小于艾里斑直径,畸变小于0.1%。结果表明该系统环境适应性强,能很好地用于红外导引头动态图像的校准。     

带摆镜的制冷型中波红外像方扫描光学系统设计

基本形式的像方扫描光学系统依然需要复杂的二维回转机构带动成像镜组做二维扫描,所以二维回转机构需要承担较大载荷。分析了基本形式的像方扫描光学系统形式,并在基本形式基础上加入摆镜,只通过二维摆镜的旋转达到扫描像面的目的,大大减小二维回转机构载荷,提高扫描速度,简化了系统结构,减小了系统体积。加入摆镜后的光学系统除具有基本形式像方扫描光学系统的性质外,还有了新的限制条件,对带摆镜的像方扫描光学系统进行了分析,提出了设计条件及设计方法,并设计出具有较大视场的像方扫描光学系统。     

片光反射遮挡式超高速亚毫米粒子探测技术

为满足在超高速碰撞靶上开展航天器抗空间碎片防护性能试验,需要准确测量速度3～10km／s,以及更高速度的毫米级或亚毫米级粒子的飞行速度,在可以实现毫米级粒子探测的片光遮挡式粒子探测技术基础上发展了片光反射遮挡式粒子探测技术,通过采用提高粒子直径与激光光束宽度的比值,解决了探测粒子直径小于1mm时探测信号弱不能识别等关键技术,研制了试验装置并开展了验证试验,研究结果表明该技术在0．2～10km／s速度范围内可实现直径为0．1mm量级粒子的有效探测。     

Ionospheric scintillations at Guilin detected by GPS ground-based and radio occultation observations

The occurrence of ionospheric scintillations with S4 ? 0.2 was studied using GPS measurements at Guilin, China (25.29°N, 110.33°E; geomagnetic: 15.04°N, 181.98°E), a station located near the northern crest of the equatorial anomaly. The results are presented for data collected from January 2009 to March 2010. The results show that nighttime amplitude scintillations only took place in February and March of the considered years, while daytime amplitude scintillations occurred in August and December of 2009. Nighttime amplitude scintillations, observed in the south of Guilin, always occurred with phase scintillations, TEC (Total Electron Content) depletions, and ROT (Rate Of change of TEC) fluctuations. However, TEC depletions and ROT fluctuations were weak during daytime amplitude scintillations, and daytime amplitude scintillations always took place simultaneously for most of the GPS satellites which appeared over Guilin in different azimuth directions. Ground-based GPS scintillation/TEC observations recorded at Guilin and signal-to-noise-ratio (SNR) measurements obtained from GPS-COSMIC radio occultation indicate that nighttime and daytime scintillations are very likely caused by ionospheric F region irregularities and sporadic E, respectively. Moreover, strong daytime amplitude scintillations may be associated with the plasma density enhancements in ionospheric E region caused by the Perseid and Geminid meteor shower activities.     

铝合金燃油-液体热交换器制造技术

分析了燃油———液体热交换器的结构特点及翅片成形和芯体焊接难点,重点介绍了翅片成形和芯体盐浴钎焊工艺方法及获得的技术经济效果。