模拟地热水温度对镀锌钢管腐蚀与结垢的影响

针对地热水环境中金属管道常见的腐蚀与结垢问题,采用扫描电子显微镜、能谱仪、X射线衍射仪等研究了不同温度的模拟地热水中镀锌钢管的腐蚀与结垢行为.结果表明:实验前期镀锌钢管的表面出现两种形貌("球"状和"针"状),不同温度的地热水中腐蚀与结垢产物的晶体形状不同,产物成分主要为Zn(OH)2,ZnO,CaCO3和MgCO3;镀锌钢管表面产物的分布对镀锌钢管在模拟地热水中的进一步腐蚀有一定程度的抑制;50℃地热水中的镀锌钢管表面的腐蚀坑面积较小,而在65℃和80℃地热水中腐蚀坑面积较大,镀锌钢管的腐蚀与结垢速度随地热水温度的升高而增大.     

一种新型机载对地观测用三轴稳定平台陀螺安装方式

陀螺安装方式及相应的算法编排是稳定平台设计中的一项关键技术。针对机载对地观测用三轴稳定平台特点,提出了将方位陀螺安装在方位环上,俯仰陀螺和横滚陀螺安装在俯仰环上的陀螺安装方式。利用空间矢量分解理论分析了陀螺输出角速度信号的投影关系及电机控制信号的分配;基于稳定平台系统模型,对理想正交情况和考虑陀螺安装误差情况进行了仿真分析,验证了此种安装方式的可行性和优越性。分析表明,在同等条件下,所提出的安装方式减小了稳定平台的机械尺寸,降低了稳定平台的重量和功耗,实现了三维角速度的正交测量,简化了三轴解耦控制算法。研究结论可为其他三轴稳定平台结构设计和陀螺安装方式设计提供参考。     

基于扩展卡尔曼滤波的动量轮故障检测方法

 动量轮作为卫星姿态控制系统的关键执行部件,对其故障检测对维持卫星的正常运行具有重要意义。首先对动量轮系统的故障进行分析,在建立动量轮线性离散状态空间模型的基础上,把动量轮的故障检测作为时变参数系统的跟踪来处理,将动量轮的模型参数作为扩展的状态空间中的状态量,使得动量轮物理模型参数与状态空间中的状态量有对应关系,通过在扩展了的状态空间上采用扩展的卡尔曼滤波,完成时变参数的跟踪。然后,将离散空间的状态量变换回连续空间中,利用物理参数与状态量的对应关系,实现对动量轮物理参数的跟踪。此方法物理意义明确,为系统的物理参数提供了定量的估计值,为进一步诊断故障原因提供了良好的基础。数值仿真表明,此方法能够通过同时检测多个故障参量,实现故障的检测并满足卫星实时性要求。     

RF MEMS器件在航天领域的应用

概述近年来国内外RF MEMS器件在航天领域的部分应用及发展趋势,重点介绍了RF MEMS开关、RF MEMS移相器和RF MEMS滤波器在航天领域的应用.     

基于匹配模板的雷达信号快速识别系统设计

雷达采用低截获概率(LPI)技术之后,特别是在低信噪比条件下,传统的雷达信号识别方法将暴露出对弱信号无能为力、识别率低等缺陷.针对这些问题,设计了基于匹配模板的雷达信号快速识别系统,介绍了系统设计的基本思路,提出了敏感参数这一概念,保证了正确识别率.以线性调频信号为例制定了相应的匹配识别准则,通过仿真实验验证了该准则的有效性和该系统的可行性.在信号受到噪声污染的情况下,该系统对线性调频信号的识别信噪比可以达到-6dB.     

LEO卫星通信系统模糊逻辑动态位置区方案

文章在基于自主定位的动态位置区方案的基础上提出了模糊逻辑动态位置区方案,通过对用户在给定时间内运动模式的判定来动态改变用户的更新半径,并仿真比较了用户在不同初始更新半径下两种方案的更新和寻呼开销,以及用户在不同模糊逻辑统计时间下的更新和寻呼开销。仿真结果表明用户在该方案下的位置管理总开销相对于普通动态位置区有了明显的降低,提高了位置管理效率。     

Direct trajectory optimization based on a mapped Chebyshev pseudospectral method

 In view of generating optimal trajectories of Bolza problems, standard Chebyshev pseudospectral (PS) method makes the points' accumulation near the extremities and rarefaction of nodes close to the center of interval, which causes an ill-condition of differentiation matrix and an oscillation of the optimal solution. For improvement upon the difficulties, a mapped Chebyshev pseudospectral method is proposed. A conformal map is applied to Chebyshev points to move the points closer to equidistant nodes. Condition number and spectral radius of differentiation matrices from both methods are presented to show the improvement. Furthermore, the modification keeps the Chebyshev pseudospectral method's advantage, the spectral convergence rate. Based on three numerical examples, a comparison of the execution time, convergence and accuracy is presented among the standard Chebyshev pseudospectral method, other collocation methods and the proposed one. In one example, the error of results from mapped Chebyshev pseudospectral method is reduced to 5% of that from standard Chebyshev pseudospectral method.     

Trajectory control strategy of cathodes in blisk electrochemical machining

A turbine blisk, which combines blades and a disk together, is one of the most important components of an aero engine. In the process of blisk electrochemical machining (ECM), the sheet cathode, which is usually used as a tool electrode, has a complicated structure. In addition to that, the channel between the adjacent blades is narrow and twisted, so interference is apt to happen when the sheet cathode feeds into the channel. Therefore, it is important to choose suitable trajectory control strategy. In this paper, a new trajectory control strategy of the sheet cathode is presented and corresponding simulation analysis is conducted on the basis of an actual blisk model. The simulation results demonstrate that the sheet cathode can feed into the channel by a spatial line trajectory without interference. Moreover, the verification experiments are carried out according to the simulation. The experimental results show that the cathode can move into the channel without interference. It is verified that the new trajectory control strategy is correct and can be used in the blisk ECM process successfully.     

过冷大水滴规章对结冰探测系统设计的影响

过冷大水滴规章提高了飞机在结冰条件下飞行的安全等级,将会对结冰探测系统的设计产生一定影响.本文概述了附录O过冷大水滴结冰条件,并对附录O第Ⅰ部分大气结冰条件进行了浅析;分析了FAR25.1420过冷大水滴结冰条件对结冰探测系统设计的影响,并提出符合相关要求的结冰探测方式;指出了对于目前申请在结冰条件下飞行的合格审定的最大起飞重量小于60 000磅或具有可逆飞行控制系统的飞机,按照FAR25.1420 (a)(1)的要求进行审定是一个较为合适的选择.此外,还给出了一种符合FAR25.1420要求的结冰探测系统方案.     

Fault detection,identification and reconstruction for gyroscope in satellite based on independent component analysis

Although satellites are designed with high reliability, faults do occur when satellites are in orbit. To avoid the important services being affected, redundancy is used in satellites. There are many sensors in satellites. In order to reduce the cost, space, weight and power consumption, redundant sensors should be added to satellite as few as possible. Analytical redundancy is an efficient way to optimize the application of redundant. The gyroscope is the attitude determination sensor of the satellite. The minimum redundant structure of the gyroscope system is as follows: three gyroscopes installed in three-axis orthogonally and one gyroscope installed with slantwise for redundancy(3o+1S).To achieve fault detection, identification and reconstruction, hypothesis of statistical independence between the three-axis angular rates and hypothesis of statistical independence between the angular rates and fault are proposed. The scenario that only one sensor is faulting and there are only additive fault and full fault is supposed. Under these assumptions, firstly a threshold method is used for fault detection. After a fault is detected, independent component analysis (ICA) based algorithm for fault identification is employed. To overcome the ambiguities of ICA, correlation coefficients and prior information of the mixed matrix are used. Finally, the reconstruction matrix is obtained. By using this matrix fault signal is extracted so that the yaw, roll and pitch axes (three-axis) angular rates of the satellite can be recovered. Numerical simulations show this method can fulfill fault detection, identification and reconstruction of the gyroscope system.