敏捷制造模式下的质量保证信息系统

客户驱动的动态的全球市场及地理上分布的合作伙伴给开发敏捷制造模式下的质量保证信息系统(QAIS)带来了新的挑战,本文先对敏捷制造模式下的QAIS进行了需求分析,提出了新的分布式QAIS的实现框架,利用当前迅速发展的信息技术,建立了QAIS的开发环境并对有关关键技术进行了初步研究,最后开发完成了一个基于Web的QAIS原型系统.     

含噪图像的处理方法与评价

接收机还原出来的显示器视频信号的电磁泄漏发射含有大量的噪声 ,导致图像模糊 ,视觉效果差。为了改善图像质量 ,提高图像的可识别度 ,需要进行图像处理 ,提取我们感兴趣的信息。介绍了几种针对含噪图像的数字信号处理方法 ,并且进行了对比分析和信噪比评价。     

一种型号专用电源转换器快速检定系统的研制

阐述了依据Q/W 892A-2007《电源转换器检定规程》研制的型号专用电源转换器快速检定系统。通过研制专用拔出力检定装置和多功能智能转换开关,实现由PC机通过系统软件自动控制测试仪器进行检定以及检定结果的处理,并自动生成原始记录和证书报告。系统具有自动、智能等优点,能够实现电源转换器的快速检定。经应用,降低了劳动强度,节省了时间,提高了检定效率。     

关于Access2000的安全机制解析

Microsoft Access 2000数据库作为常用的桌面数据库软件，在中小型的数据库系统中得到了广泛的应用。针对Access2000安全性能不高，探讨如何设置及提高Access2000的安全性方法。     

A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

Optimization of beamforming and path planning for UAV-assisted wireless relay networks

Recently, unmanned aerial vehicles （UAVs） acting as relay platforms have attracted considerable attention due to the advantages of extending coverage and improving connectivity for long-range communications. Specifically, in the scenario where the access point （AP） is mobile, a UAV needs to find an efficient path to guarantee the connectivity of the relay link. Motivated by this fact, this paper proposes an optimal design for beamforming （BF） and UAV path planning. First of all, we study a dual-hop amplify-and-forward （AF） wireless relay network, in which a UAV is used as relay between a mobile AP and a fixed base station （BS）. In the network, both of the AP and the BS are equipped with multiple antennas, whereas the UAV has a single antenna. Then, we obtain the output signal~to-noise ratio （SNR） of the dual-hop relay network. Based on the criterion of maximizing the output SNR, we develop an optimal design to obtain the solution of the optimal BF weight vector and the UAV heading angle. Next, we derive the closed-form outage probability （OP） expression to investigate the performance of the dual-hop relay network conveniently. Finally, computer simulations show that the proposed approach can obtain nearly optimal flying path and OP performance, indicating the effectiveness of the proposed algorithm. Furthermore, we find that increasing the antenna number at the BS or the maximal heading angle can significantly improve the performance of the considered relay network.     

基于自适应粒子滤波的涡扇发动机故障诊断

针对涡扇发动机非线性、非高斯的特点,提出了一种自适应的粒子滤波算法用于涡扇发动机气路部件突变故障的诊断.为了减小算法的计算量并且保证滤波精度,分析了滤波精度和样本数目的关系,提出根据滤波过程中状态的方差自适应地调整粒子数,在保证一定的滤波精度下可以有效地减少滤波过程中使用的粒子数,提高了算法的实时性.同时,引入扩展卡尔曼滤波(EKF)用于更新粒子,产生重要概率密度函数,在一定程度上避免了粒子的退化.通过某型涡扇发动机的仿真分析表明:改进的算法相比标准粒子滤波算法用于涡扇发动机气路部件故障诊断时,参数估计的方均根误差减小了50%左右,且算法的计算量减小了30%.     

拉形条件对镜面蒙皮成形质量的影响

在充分考虑滑移带出现与成形件贴模度的基础上,通过分析拉形速度、毛料几何尺寸、模具几何参数、润滑方式对成形质量的影响,确定了合理的飞机镜面蒙皮拉形条件.结果表明,改善板料变形的均匀性,延缓滑移带出现,增加成形面内材料的变形程度,是制定最优工艺参数、提高成形质量的主要措施.     

基于小生境遗传算法的航空发动机维修构型控制

为实现航空发动机维修中构型控制,建立了基于Petri网的构型控制描述模型,通过变迁序列的激发求得改型后可能的零件集合,作为后续的约束满足条件,并提出一种基于小生境遗传算法的发动机构型多方案求解方式.