全文获取类型
收费全文 | 1217篇 |
免费 | 252篇 |
国内免费 | 359篇 |
专业分类
航空 | 925篇 |
航天技术 | 300篇 |
综合类 | 191篇 |
航天 | 412篇 |
出版年
2024年 | 4篇 |
2023年 | 5篇 |
2022年 | 42篇 |
2021年 | 43篇 |
2020年 | 44篇 |
2019年 | 31篇 |
2018年 | 34篇 |
2017年 | 31篇 |
2016年 | 32篇 |
2015年 | 49篇 |
2014年 | 70篇 |
2013年 | 93篇 |
2012年 | 101篇 |
2011年 | 83篇 |
2010年 | 92篇 |
2009年 | 92篇 |
2008年 | 92篇 |
2007年 | 69篇 |
2006年 | 76篇 |
2005年 | 74篇 |
2004年 | 50篇 |
2003年 | 54篇 |
2002年 | 59篇 |
2001年 | 59篇 |
2000年 | 56篇 |
1999年 | 35篇 |
1998年 | 36篇 |
1997年 | 36篇 |
1996年 | 36篇 |
1995年 | 31篇 |
1994年 | 39篇 |
1993年 | 41篇 |
1992年 | 22篇 |
1991年 | 29篇 |
1990年 | 25篇 |
1989年 | 24篇 |
1988年 | 12篇 |
1987年 | 7篇 |
1986年 | 6篇 |
1985年 | 5篇 |
1984年 | 1篇 |
1982年 | 4篇 |
1981年 | 2篇 |
1980年 | 1篇 |
1965年 | 1篇 |
排序方式: 共有1828条查询结果,搜索用时 343 毫秒
101.
高强Al-Cu-Li-X铝锂合金2A97三级时效工艺及性能研究 总被引:2,自引:0,他引:2
以新型高强Al-Gu-Li-X铝锂合金2A97为研究对象,通过拉伸试验研究两种三级时效工艺及其改型工艺对合金性能的影响.结果表明,含有δ′相二次析出过程的三级时效和含有δ′相回溶过程的三级时效处理合金的强度和塑性达到T6峰值时效水平,三级时效改型工艺由于增加变形使前者合金的强度升高,塑性降低,使后者的强度显著提高.三级时效和单级时效合金的主要显微组织有δ′相、θ″/θ′相和T1相.三级时效改型工艺由于增加变形促进δ′相析出和δ′相回溶,同时变形促进T1相析出,从而改变了主要强化相δ′相和T1相的数量. 相似文献
102.
多层钎焊结构件超声C扫描信号特征分析 总被引:1,自引:0,他引:1
对多层钎焊件内层焊缝检测中产生的多重声束路径叠加现象进行了详细分析,并用计算机模拟超声检测中的叠加信号,总结出对等厚薄板钎焊缝阵结构内层焊缝的检测方法及C扫描时信号门放置的合理位置,并且在实际检测中验证了该方法的正确性. 相似文献
103.
为了研究桨叶刚柔耦合特性,采用中等变形梁模型处理桨叶弹性变形,分别采用小转角和有限转角两种方法处理桨叶绕铰的刚性运动。以桨叶扬起下坠碰撞问题为研究对象。计算分析表明:(1)弹性桨叶存在较明显的刚性运动和弹性变形耦合;(2)挥舞角较小时,两种处理方法计算结果一致,均与试验数据吻合较好;(3)挥舞角较大时,刚柔耦合增强,两种处理方法的计算值差别较为明显;(4)桨叶弯曲刚度对桨叶刚柔耦合特性有较明显影响,刚度越小,耦合越强;(5)桨叶如果比较柔软,小转角处理方法计算值相对有限转角处理方法,相位滞后、幅值增加均较为明显,计算桨叶动响应时需引起注意。 相似文献
104.
105.
106.
107.
基于CATIA的机床夹具元件快速造型方法 总被引:1,自引:0,他引:1
介绍了基于CATIA的CAA架构对实体进行参数化建模的方法,以一个航空夹具设计为实例,开发了基于CAA及零件特征的参数化航空夹具设计模块,为基于CATIA的航空夹具元件快速造型做了技术方法的探索. 相似文献
108.
Nonlinear Dynamics Behaviors of a Rotor Roller Bearing System with Radial Clearances and Waviness Considered 总被引:2,自引:1,他引:2
A rotor system supported by roller beatings displays very complicated nonlinear behaviors due to nonlinear Hertzian contact forces, radial clearances and bearing waviness. This paper presents nonlinear bearing forces of a roller bearing under four-dimensional loads and establishes 4-DOF dynamics equations of a rotor roller bearing system. The methods of Newmark-β and of Newton-Laphson are used to solve the nonlinear equations. The dynamics behaviors of a rigid rotor system are studied through the bifurcation, the Poincar è maps, the spectrum diagrams and the axis orbit of responses of the system. The results show that the system is liable to undergo instability caused by the quasi-periodic bifurcation, the periodic-doubling bifurcation and chaos routes as the rotational speed increases. Clearances, outer race waviness, inner race waviness, roller waviness, damping, radial forces and unbalanced forces-all these bring a significant influence to bear on the system stability. As the clearance increases, the dynamics behaviors become complicated with the number and the scale of instable regions becoming larger. The vibration frequencies induced by the roller bearing waviness and the orders of the waviness might cause severe vibrations. The system is able to eliminate non-periodic vibration by reasonable choice and optimization of the parameters. 相似文献
109.
研究了随机载荷作用次数对系统可靠性的影响,指出传统的可靠性模型并不能很好地反映载荷作用次数对系统可靠性的影响,运用载荷-强度干涉模型和顺序统计量理论建立了随机载荷多次作用下的共因失效系统可靠性模型.考虑系统中零件的失效相关性,在不作失效独立假设的前提下,运用系统级载荷-强度干涉模型建立了共因失效系统可靠性模型.根据随机载荷作用的统计学意义,运用顺序统计量理论建立了载荷多次作用时等效载荷的累积分布函数和概率密度函数,在此基础上,建立了随机载荷多次作用下的共因失效串联系统、并联系统以及k/n系统可靠性模型. 相似文献
110.
提出了用最小二乘估计解算辐射源位置,在迭代过程中通过地理信息系统查询并不断修正目标高程,同时其定位误差进行了分析和仿真。结果表明,修正高程误差后可以改进目标高程定位精度,进而促进水平定位精度,水平定位精度的提高又会促进在高度上的定位,从而使整体的定位精度得到了改善。 相似文献