可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

Global ionospheric scintillations revealed by GPS radio occultation data with FY3C satellite before midnight during the March 2015 storm

Global observations of S4 amplitude scintillation index by the GPS Occultation Sounder (GNOS) on FengYun-3 C (FY3C) satellite reveal global dynamic patterns of a strong pre-midnight scintillations in F-region of the ionosphere during the St. Patrick’s Day geomagnetic super storm of 17–19 March 2015. The observed strong scintillations mainly occurred in the low latitudes, caused by equatorial plasma bubbles. During the main storm phase (March 17), the scintillations were first triggered in the New Zealand sector near 160°E longitudes, extending beyond 40°S dip latitude. They were also enhanced in the Indian sector, but significantly suppressed in East Asia near 120°E longitude and in Africa around 30°E longitude. During the initial recovery phase (March 18–19), the global scintillations were seldom observed in GNOS data. During the later recovery phase (after March 19), the scintillations recovered to the pre-storm level in Indian, African, and American sectors, but not in East Asian and any of Pacific sectors. These results closely correlate with observations of the density depletion structures by the Communication/Navigation Outage Forecasting System (C/NOFS) satellite, and ground-based instruments. Such consistency indicates reliability of our scintillation sensing approach even in a case-by-case comparison study. The prompt penetration electric field and disturbance dynamo electric field are suggested as the main factors that control the enhancement and inhibition of the scintillations during the storm, respectively.     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

丁腈橡胶增韧环氧树脂基烧蚀防热材料性能

以丁腈橡胶(CTBN)为增韧剂对环氧树脂(F51)进行增韧改性,通过FTIR、TG以及力学性能测试研究了丁腈橡胶对环氧树脂固化反应、热稳定性能和力学性能的影响,并分析了其增韧机理;分别采用燃气流剪切烧蚀试验和电弧风动烧蚀实验考核了低密度烧蚀材料的烧蚀性能。结果表明:经CTBN改性后,两者的分子链产生了一定程度的交联;树脂基体的拉伸、弯曲性能有所下降,但韧性得到了增强;热稳定性大大提高,增韧后的F51树脂在800℃时的残重率由增韧前的23%提高到了54%;低密度烧蚀材料的抗剪切、抗剥蚀能力得到了增强,且碳层的尺寸稳定性也得到了改善,烧蚀性能提高。     

在实时嵌入式环境下利用电子盘实现大容量数据记录的软件设计研究

嵌入式环境和实时操作系统目前广泛应用于航空领域。本文在介绍嵌入式系统的基础上,重点对实时多任务环境下大容量数据记录的实现方式进行了研究和利用,最后展望了电子盘实时多任务系统中记录大容量数据的前景。     

Microwave Photonics for Modern Radar Systems

The emerging new concepts and technologies based on microwave photonics have led to an ever-increasing interest in developing innovative radar systems with a net gain in functionality, bandwidth/resolution, size, mass, complexity and cost when compared with the traditional implementations. This paper describes the techniques de- veloped in the last few years in microwave photonics that might revolutionize the way to design multifunction radar systems, with an emphasis on the recent advances in optoelectronic oscillators （OEOs）, arbitrary waveform gener- ation, photonic mixing, phase coding, filtering, beamforming, analog-to-digital conversion, and stable radio-fre- quency signal transfer. Challenges in implementation of these components and subsystems for meeting the technique requirements of the multifunction radar applications are discussed.     

硅半球深腔结构无损检测技术

半球深腔的加工质量是决定硅基MEMS半球陀螺精度的关键因素之一，及时检测半球深腔的形貌参数并将其反馈至加工过程，是确保高性能MEMS半球陀螺研制成功的重要措施。由于硅半球深腔的深度较大，台阶仪和光学显微成像系统无法对半球深腔的形貌特征进行有效测量。因此,需要将硅深腔结构剖开后采用扫描电镜(SEM)进行检测。这种检测方式时间周期长，且属于破坏性的样本检测，效率和测试精度都较低。提出以硅半球深腔为模具，利用PDMS铸模将硅半球深腔的结构尺寸和表面形貌转移到PDMS凸起的半球模型上，通过检测PDMS半球模型的尺寸结构和表面形貌，即可反推出硅半球深腔的尺寸特征。经实验验证，脱模后的PDMS模型可以准确地反映出半球深腔的尺寸信息，测量结果的不确定度小于5‰，有效解决了硅半球深腔无损检测的难题。     

RTK model and positioning performance analysis using Galileo four-frequency observations

This paper proposes a real-time kinematic (RTK) model that uses one common reference satellite for the Galileo system with four frequency observations. In the proposed model, the double-differenced (DD) pseudorange and carrier phase biases among the different frequencies are estimated as unknown parameters to recover the integer features of the DD ambiguities among the different frequencies for ambiguity resolution and precise positioning. Analysis results show that the E5a, E5b, and E5 frequencies have virtually the same performance in terms of the positioning accuracy, observation residuals, and ratio values of ambiguity resolution. However, the E1 frequency performs worse than the E5a, E5b, and E5 frequencies. The RTK results for the combination of multiple frequencies are much better than those for a single-frequency observation, the coordinates’ standard deviation is improved about 20–30%, and the ambiguity fix time is improved about 10%.     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。