捷联惯导/里程计组合导航方法

针对车载自主导航需求,基于卡尔曼滤波器,实现捷联惯导与里程计量测信息的组合导航.推导了里程计误差模型,结合捷联惯组误差模型与捷联系统误差模型,建立了捷联惯导/里程计自主组合导航系统误差状态模型.建立了捷联惯导/里程计组合导航量测模型,阐述了估计误差修正方法.采用仿真计算对此方法进行了验证,仿真结果表明:组合导航过程中,初始姿态误差能得到有效估计,姿态误差和位置误差均能控制在一定精度范围内,应用此组合导航方法相对于传统的航位推算方法能得到更高的导航精度,能有效实现自主高精度定位定向.     

基于自适应心跳算法的分布式系统故障检测器

故障检测是容错分布式系统中的关键技术之一.为了提高故障检测的性能,提出一种新型的故障检测器——自适应心跳检测器(SA-HD, Self-Adaptive Heartbeat Detector).SA-HD采用了基于拉式(pull)的自适应心跳算法,在考虑故障检测性能的同时也考虑了心跳检测所占用的网络资源对网络性能的影响.SA-HD能够根据网络负载调节自身发送心跳消息的频率,提高了心跳检测的网络环境适应能力,尤其是在高负载的环境下,能够有效改善心跳检测的性能.建立了SA-HD的模型,对其性能进行了仿真分析,并通过试验验证了SA-HD性能要优于传统推式(push)的心跳检测器.     

带防热层复合材料锥壳热固化变形的数值模拟

采用数值模拟方法研究带防热层缠绕成型复合材料锥壳热固化变形的形成机理和影响因素.建立了带防热层复合材料锥壳热固化变形预测的三维有限元程序.计算结果表明:外层防热材料和内层结构材料热膨胀系数不匹配是引起壳体固化变形的主要原因.提出在内层和外层之间增加中间过渡层的方法控制壳体的固化变形,中间层材料为丁腈橡胶片时可使固化变形减小20%以上.采用数值模拟方法讨论了中间层模量、厚度以及缠绕张力对壳体固化变形的影响,分析结果表明:固化变形随中间层模量的增加而增加,随中间层厚度的增加略有减小;缠绕张力释放增加壳体的固化变形,缠绕张力越大引起的固化变形越大.     

多变量模型参考自适应控制及在飞行控制中的应用

讨论了多变量模型参考自适应控制及其在飞行控制中的应用问题.针对相对阶任意的多输入多输出线性时不变系统,提出了一种模型参考自适应控制方案.基于SDU分解,仅要求高频增益矩阵的顺序主子式的符号已知,从而放宽了对高频增益矩阵的限制.通过构造合适的Lyapunov函数,证明了闭环系统的全局稳定性和跟踪误差的渐进收敛性.将所提方案应用到了飞行控制系统,仿真结果验证了所提方案的有效性.     

氧化物涂层对航天器材料原子氧剥蚀的防护

采用磁控溅射方法在航天器常用材料聚酰亚胺(Kapton)表面沉积无机氧化物涂层(TiO₂和SiO₂),来提高材料的抗原子氧剥蚀性能.通过选择试验材料和参数,优化了沉积涂层的工艺,以克服容易产生裂纹的缺点.对材料进行了原子氧效应地面模拟试验,结果表明,在Kapton上沉积涂层后,质量损失下降了2个数量级.另外,有涂层的Kapton表面基本没有变化并且没有出现裂纹.其中,TiO₂由于热膨胀系数更接近Kapton,比SiO₂的防护效果更好.     

整机产品失效机理危害度定量分析方法

针对整机产品失效机理多而复杂、失效数据少、主失效机理分析为定性方法的现状,提出了一种基于Bayes的失效机理危害度定量分析方法.首先利用Dirichlet分布描述产品的先验信息,结合现场失效数据确定失效频率的Bayes后验分布函数,然后通过Slice抽样方法获得失效频率的满条件分布,进而利用Gibbs抽样得到其Bayes估计,从而实现了各失效机理的定量分析.最后在某型光纤连接器失效机理已分析清楚的前提下,分别用FMMEA(Failure Modes,Mechanisms and Effects Analysis)及Bayes方法确定了其主失效机理,结果表明基于Bayes的失效机理危害度定量分析方法考虑了现场未出现的失效机理危害度,其确定的主失效机理比FMMEA结果更具有可信度.     

基于高增益观测器的航迹角自适应反步控制

针对飞行控制系统中状态向量不完全可测量的问题,设计了一种高增益神经网络自适应观测器.在常规高增益观测器的基础上引入径向基(RBF, Radial Basis Function)网络自适应项,对建模误差和外界干扰进行在线估计.将高增益观测器与基于动态面的反步控制相结合,提出了一种神经网络自适应反步控制方法.引入一阶滤波器,避免了传统反步控制中的"计算膨胀"问题.基于Lyapunov稳定性理论,给出自适应输出反馈控制器和RBF网络权值向量的自适应律,并证明了闭环系统是半全局一致有界.从航迹角控制系统仿真结果可以看出,航迹角能够较好地跟踪指令信号,不受建模误差和外界干扰的影响,所设计的观测器具有良好的收敛性,控制系统具有较高的鲁棒性.     

Optimization of communication network topology for navigation sharing among distributed satellites

Navigation sharing among distributed satellites is quite important for coordinated motion and collision avoidance. This paper proposes optimization methods of the communication network topology to achieve navigation sharing. The whole communication network constructing by inter-satellite links are considered as a topology graph. The aim of this paper is to find the communication network topology with minimum communication connections’ number (MCCN) in different conditions. It has found that the communication capacity and the number of channels are two key parameters affecting the results. The model of MCCN topology for navigation sharing is established and corresponding method is designed. Two main scenarios, viz., homogeneous case and heterogeneous case, are considered. For the homogeneous case where each member has the same communication capacity, it designs a construction method (Algorithm 1) to find the MCCN topology. For the heterogeneous case, it introduces a modified genetic algorithm (Algorithm 2) to find the MCCN topology. When considering the fact that the number of channels is limited, the Algorithm 2 is further modified by adding a penalized term in the fitness function. The effectiveness of these algorithms is all proved in theoretical. Three examples are further tested to illustrate the methods developed in this paper.     

Autonomous navigation of Mars probe using X-ray pulsars: Modeling and results

Autonomous navigation of Mars probe is a main challenge due to the lack of dense ground tracking network measurements. In this paper, autonomous navigation of the Mars probe Orbits is investigated using the X-ray pulsars. A group of X-ray pulsars with high ranging accuracy are selected based on their properties and an adaptive extended Kalman filter is developed to incorporate the Mars probe dynamics and pulsar-based ranging measurements. Results of numerical experiment show that the three-dimensional positioning accuracy can achieve 750m in X-axis, 220m in Y-axis and 230m in Z-axis, which is much better than the positioning results by current Very Long Baseline Interferometry (VLBI) or Doppler observations with the accuracy of 150 km or several kilometers, respectively.