磁轴承控制器的设计及仿真研究

介绍了磁轴承系统的组成,对控制器性能的基本要求及控制方案的选择,分析了典型ＰＩＤ控制器存在的两个弊端,提出了磁轴承控制器的四种模型。通过对这四种模型的仿真研究,分析了各模型中比例系数、积分时间常数、微分时间常数及局部反馈系数对系统性能的影响,并给出了各参数较为理想的参考值及阶跃响应曲线,仿真结果对制作模拟控制器及数字控制器有一定的借鉴作用。     

对国有企业质量发展的探索

概述了国有企业质量发展面临的问题及解决这些问题的对策;并对国有企业质量发展的重点、模式和指导思想等提出了看法.     

Determination of optimal samples for robot calibration based on error similarity

Industrial robots are used for automatic drilling and riveting.The absolute position accuracy of an industrial robot is one of the key performance indexes in aircraft assembly,and can be improved through error compensation to meet aircraft assembly requirements.The achievable accuracy and the difficulty of accuracy compensation implementation are closely related to the choice of sampling points.Therefore,based on the error similarity error compensation method,a method for choosing sampling points on a uniform grid is proposed.A simulation is conducted to analyze the influence of the sample point locations on error compensation.In addition,the grid steps of the sampling points are optimized using a statistical analysis method.The method is used to generate grids and optimize the grid steps of a Kuka KR-210 robot.The experimental results show that the method for planning sampling data can be used to effectively optimize the sampling grid.After error compensation,the position accuracy of the robot meets the position accuracy requirements.     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.     

3-D position estimation of isolated target and optimal trajectory choice in parasitic synthetic aperture radar

Bistatic SAR (BSAR) systems have recently been the subject of several studies, but little attention has been given to the potential of the location of targets. In the paper, the performance of the estimation of 3-D position of a target (TPE) in parasitic SAR is obtained analytically and illustrated by computer simulation using ambiguity function analysis, and the maximum likelihood estimate (MLE) approach. It was shown that by using a multi look parasitic BSAR all three coordinates of an isolated point target (IPT) could be evaluated. Analytical closed form equations that characterize the measurement accuracy were derived. In the final these equations will be used to demonstrate various cases of more practical, including optimal trajectories choice under any geometry configuration case, moreover, the conclusion is verified via Matlab.     

七轴超精密铣-车复合加工中心RM3-7 Axes

RM3-7 Axes七轴高速超精密铣-车复合加工中心,是SPINNER-REALMECA最新推出的高端产品,适用于航空、航天、医疗器械、生物医学,微精机械、电子通信、汽配制造、光学零件等高技术领域的精细复杂加工.     

Electrochemical micromachining of micro-dimple arrays on cylindrical inner surfaces using a dry-film photoresist

The application of surface textures has been employed to improve the tribological performance of various mechanical components. Various techniques have been used for the application of surface textures such as micro-dimple arrays, but the fabrication of such arrays on cylindrical inner surfaces remains a challenge. In this study, a dry-film photoresist is used as a mask during through-mask electrochemical micromachining to successfully prepare micro-dimple arrays with dimples 94 lm in diameter and 22.7 lm deep on cylindrical inner surfaces, with a machining time of 9 s and an applied voltage of 8 V. The versatility of this method is demonstrated, as are its potential low cost and high efficiency. It is also shown that for a fixed dimple depth, a smaller dimple diameter can be obtained using a combination of lower current density and longer machining time in a passivating sodium nitrate electrolyte.     

F12/环氧复合材料力学性能研究

测定了Ｆ１２／环氧复合材料的基本力学性能,并比较了Ｆ１２纤维在单向板、强力环及薄壁容器中的纤维强度转化率。实验结果表明,Ｆ１２／环氧单向复合材料与其ＮＯＬ环的拉伸强度相近,而薄壁容器中的复合强度约为单向拉伸强度的６０％,但三种复合材料的纤维强度转化率相近,约为（７０．１±１．６）％。