全文获取类型
收费全文 | 2427篇 |
免费 | 834篇 |
国内免费 | 454篇 |
专业分类
航空 | 2346篇 |
航天技术 | 399篇 |
综合类 | 243篇 |
航天 | 727篇 |
出版年
2024年 | 17篇 |
2023年 | 83篇 |
2022年 | 189篇 |
2021年 | 177篇 |
2020年 | 179篇 |
2019年 | 183篇 |
2018年 | 183篇 |
2017年 | 200篇 |
2016年 | 168篇 |
2015年 | 167篇 |
2014年 | 196篇 |
2013年 | 186篇 |
2012年 | 215篇 |
2011年 | 207篇 |
2010年 | 168篇 |
2009年 | 157篇 |
2008年 | 166篇 |
2007年 | 166篇 |
2006年 | 141篇 |
2005年 | 132篇 |
2004年 | 119篇 |
2003年 | 88篇 |
2002年 | 84篇 |
2001年 | 73篇 |
2000年 | 38篇 |
1999年 | 28篇 |
1998年 | 4篇 |
1997年 | 1篇 |
排序方式: 共有3715条查询结果,搜索用时 156 毫秒
881.
The performance of a marine gas turbine intercooler operating in wet condition was evaluated.The intercooler was a cross-flow plate-fin heat exchanger that used air and pure water as its working fluids at the hot and cold sides,respectively.The heat transfer performance and the water vapor condensation were investigated for a relative humidity of the inlet air that reached 100% during warship cruise.The condensation of the water vapors increased the hot side outlet temperature by a certain amount,which could in turn influence the performance of the compressor downstream.The condensate film thickness and the void fraction were calculated based on an annular two-phase flow model.It is found that water vapor condensation in hot flow channel increases the outlet temperature with a maximum value of 7.3℃ in the case of 100% relative humidity.The calculated liquid film thickness reaches a maximum value of 4μm,which indicates negligible thermal resistance to heat transfer.The results of liquid film thicknesses also provide a qualitative prediction of the diameter distribution of the condensate water droplets. 相似文献
882.
克努森数对微尺度相似流动特性影响的实验 总被引:1,自引:0,他引:1
为了研究克努森数(Kn)对微尺度相似流动特性的影响,选取理论孔径分别为0.357 4mm的小孔和3.6mm的相似放大孔实验件,并保证相同的长径比.在相同的雷诺数(Re)下对孔的Kn相同和不同的情况进行实验研究,计算孔的流量系数并进行分析比较.结果表明:在相同的Re下,小孔与相似放大孔在Kn相同时,两者流量系数吻合性很好;在Kn不同时,小孔和相似放大孔流量系数不同.因此在采用相似放大模型研究微尺度结构的流动特性时,必须保证相似放大件和微尺度原件Kn相同. 相似文献
883.
对一种设计马赫数为5的一级二元混压式进气道再入大气层过程典型状态进行了仿真和风洞试验,得到了该进气道典型状态下的气动特性.结果表明:当来流马赫数高于设计马赫数(为5)时,进气道外压斜激波系提前汇合,与唇罩入射斜激波相互作用,产生了波-波干扰;尽管发生了流动分离,但当来流马赫数为7和6时进气道出口上游气流紊流度分别不超过3.337和3.256,且流道内动态压力信号的功率谱密度呈现白噪声特征,不会对发动机造成结构损伤.因此,对于宽来流马赫数工作范围的进气道来讲,为了提供足够的流量,可以适当降低进气道的设计马赫数. 相似文献
884.
建立了双输入圆柱齿轮分流传动系统的弯扭耦合动力学模型,模型中考虑了各齿轮副间的时变啮合刚度、齿侧间隙、啮合误差、啮合阻尼等因素.结合闭环结构特点,利用齿轮啮合线的相对位移和传动轴扭转位移消除方程中的刚体位移.采用4阶Runge-Kutta法求解系统动力学方程,获得了系统均载系数.结果表明:系统均载系数受输入轴扭转刚度影响小;分流级和并车级均载系数对双联齿轮轴的扭转刚度敏感,减小双联齿轮轴的扭转刚度可以改善系统的均载性能,当双联齿轮轴的扭转刚度小于1.1×105(N·m)/rad时,可将系统均载系数控制在1.06以内;输出轴扭转刚度的变化对分流级和并车级均载系数基本没有影响. 相似文献
885.
886.
887.
888.
889.
890.
采用一种预旋喷气机匣处理提高离心压气机特定转速范围内的稳定裕度.通过引气加大离心叶轮进口基元级流量降低通道堵塞,并借助回流预旋喷气改变前缘攻角抑制叶背分离是该机匣处理扩稳的主要机理.基于这样的认识,对机匣处理做了几何参数设计研究,发现轴向搭接位置、搭接长度和开槽角度是影响机匣处理性能的3个主要参数.通过几何参数的合理选取,在尽量提高80%设计转速稳定裕度的同时兼顾100%设计转速的效率.压气机部件性能试验验证了该设计方法的有效性,并观测到在低转速时,机匣处理可以同时提高稳定裕度和效率. 相似文献