连翼布局飞机及探测无人机研究进展

在收集、整理、分析国外连翼布局飞机研究资料的基础上,介绍了国外连翼布局飞机的研究历程和设计特点;特别是基于近年来对未来战场信息情报、监视、侦察任务的需求,介绍了连翼布局探测无人机这一新的作战概念和装备技术的研究进展情况。     

DSP的数学原理及在实时系统的应用

制造系统里所用的微处理器中，单片机只能做逻辑处理和简单数学计算，而数字信号处理器（DSP）可进行相当复杂的数学处理。本文概述DSP的数学原理及其技术特点，介绍了基于DSP智能控制器在制造业中实时测控系统的应用实例。     

铝合金薄板焊接热裂敏感性探索

探讨了用钨极氩弧焊焊接铝合金ＬＹ１２ＣＺ及ＬＹ１２Ｍ薄板时其热裂纹的变化规律，并分析了焊接工艺参数及填充材料对热裂纹的影响。试验结果表明，选择合适的工艺参数和填充材料可以明显提高该类合金的抗裂性能。     

机器人预见控制方法的研究

提出了一种机器人高精度路径控制的有效方法－－以面积误差作为评价函数的预见控制方法。该方法从目标路径与实际路径之间的面积误差评价函数值最小化观点出发，运用逐次最优化原理来求取最优预见控制输入，它的特点是在每一采样时刻都要更新反馈系数和预见前馈系数，由于这些系数都是离线计算，因此并不影响实时控制速度，最后，通过实际机器人仿真，结果表明，该方法对于满足机器人高速度、高精度的要求是行之有效的。     

模拟月壤研制的初步设想

模拟月壤是月球样品的地球化学复制品，作者总结世界上已有的5种模拟月壤JSC-1，MLS．1，MLS-2，MKS-1和FJS-1的研制过程、方法与基本理化性质，认为系列化模拟月壤研制对中国首次月球探测有重要意义，在此基础上，作者提出系列化模拟月壤研制的基本思路．     

控制系统通用综合测试系统组建研究

在分析系统需求和基本功能的基础上 ,采用VXI总线技术、远程测控技术和测试应用程序自动生成等关键技术 ,按照综合测试的总体要求进行系统集成 ,组建控制系统通用综合测试系统 ,包括系统硬件和软件方案 ,对系统的硬件结构方案、模件选型以及软件流程、组成和作用进行了详细讨论。     

线阵CCD平场校正及FPGA实现的研究

为了消除由于照明光源的非均匀性、镜头渐晕及CCD传感器噪声对图像质量造成的不良影响,首先从理论上分析了线阵CCD固定模式噪声和像素光电响应非均匀性的数学模型和产生的原因;对像素光电响应非均匀性这一主要影响因素,根据其光电响应模型提出了CCD像素光电响应非均匀性的两点校正方法,即求解出各个像素光电响应不均匀性的校正因子和暗偏置量系数,进而用以计算各个像素的校正量,实现逐点校正;针对校正算法大数据量、实时计算的要求,设计了基于现场可编程逻辑门阵列FPGA快速实现校正算法的硬件处理结构。最后,通过仿真和实验表明,两点校正方法可以有效地减小CCD像素光电响应不均匀性的图像噪声,提高图像质量,以便做后续精确处理。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.