高原航线运行控制研究:以“成都-稻城”航线为例

以"成都—稻城"航线为案例论述了高原航线的运行特点,根据航线的实际运行,提出运行控制的建议,研究表明:1)稻城机场天气报文中有17个小时为自动观测,需放行签派员与机场气象部门和场务部门联系确认发展趋势和跑道道面情况; 2)受四季气象特点的限制,推广新技术和适当增加航班备份燃油等措施对航班的签派放行和运行控制有重要的作用; 3)对复杂天气的评估和一发失效及客舱释压应急处置程序是高原航线运行控制的难点; 4)签派员参加高原机场"全动模拟机"训练和高原机场航线实习,有助于提升高原航线运行控制能力。     

腔室型旋流发生器的设计与仿真研究

为了模拟旋流畸变对压气机性能和稳定性的影响,设计了一套腔室型旋流发生器,通过灵活改变腔室几何构形来形成不同类型和强度的旋流,利用先进的CFD数值模拟方法开展了旋流器流场特征的研究并对旋流畸变指标进行了详细分析。结果表明,腔室型旋流发生器能够产生不同强度的整体涡和对涡旋流,气动交界面处整体涡最大旋流角可以达到65.8°,对涡最大旋流角可以达到58.2°;在压气机进口截面,近壁面处旋流强度最大,整体涡可达43.5,对涡可达9.26;整体涡主要影响叶尖流场,对涡主要影响叶尖和叶根的流场。随着流量的增加,旋流器总压恢复系数降低,整体涡强度增加,对涡强度降低。     

下端壁流向槽抽吸对高负荷扇形扩压叶栅性能影响的数值研究

为探究附面层抽吸对亚声速高负荷扇形扩压叶栅气动性能和流场结构的影响,利用数值方法对叶栅进行了下端壁流向槽附面层抽吸的研究。对比原型和各抽吸方案发现:下端壁附面层的抽吸可以有效抑制下角区低能流体的分离及回流,降低下角区总压损失并提升叶栅近端壁区域的扩压能力,但上角区分离会略有加剧。当抽吸质量流量为原型叶栅质量流量的0.50%时,抽吸槽起始于角区分离点下游附近的抽吸方案(EW2)效果最佳,叶栅整体总压损失降低27.65%,静压比提升8.69%。     

基于正交试验的超声波喷丸成形工艺参数分析及弧高值预测

针对带筋板的超声波喷丸成形,采用正交试验法研究了撞针速度、撞针直径、成形轨迹间距、喷丸区域宽度对带筋板超声波喷丸成形弧高值的影响,得出最佳参数组合方案,并以此作为样本数据,建立多元回归分析数学模型。通过实验验证模型的准确性,试验数据和回归分析数据相符较好,可以用回归分析的数学模型来预测喷丸弧高值,提高工艺设计效率。     

波音737NG飞机水平安定面疲劳裂纹处理方法分析

根据波音737NG飞机的维护数据,该文分析波音737NG飞机水平安定面主要结构的受力特性;同时,定性分析了水平安定面肋下缘条及连接的蒙皮等部位的典型疲劳裂纹。分析波音公司针对该问题对现有机队的预防性改进措施,借鉴大修厂的实际维护经验以及一系列数据和现场照片,最终给出针对该疲劳裂纹的建议措施,以供民机设计制造单位及波音737NG营运人参考借鉴。     

温度场对航空发动机转子超转破裂的影响

CCAR33.27超转适航要求,分析和试验确定的超转转速,必须基于温度和温度梯度的最不利组合。因此,研究温度和温度梯度对超转破裂的影响有非常重要的意义。以某型航空发动机低压6级涡轮转子为例,采用极限应变方法开展了转子部件的超转破裂分析,对比了常温和高温（红线转速对应的温度分布）下转子关键轮盘应变分布趋势和应变增长规律、预测的超转破裂的起始位置和破裂转速等轮盘超转特性;针对超转破裂分析,提出了在高温条件下,经过常温超转破裂试验验证的方法应用的有效性条件。低压涡轮转子的分析结果也显示,红线转速对应的温度状态下,轮盘超转破裂转速比常温下显著降低,而高温下材料屈服强度的大幅降低则是破裂转速下降的主要原因。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

悬臂静子间隙影响的计算分析

悬臂静子在小型涡轮喷气和涡轴发动机的轴流压气机上广泛应用,为了探讨不同条件下悬臂静子间隙的影响,在特定的环境下,分别针对常规负荷和高负荷、小轮毂比和中等轮毂比,组合成几种不同方案,计算分析了静子根部径向间隙分别为弦长的0%、0.25%、0.5%、1%、1.5%和2%情况。计算结果表明:与叶栅中情况类似,在压气机中,悬臂静子同样存在一个特性上表现最优的最佳间隙;在根部未发生角区失速的大流量状态和设计状态,间隙的引入会使得特性恶化,在根部发生角区失速后的小流量状态,间隙的引入则能使得特性变优;间隙形成的泄漏流对角区分离的影响与间隙大小和角区分离程度相关;压气机设计状态负荷水平减小后,间隙的影响规律基本不变;轮毂比增大后,最佳间隙值有减小的趋势。     

基于图和子图同构算法的制造特征识别方法

针对传统制造特征难以快速识别的难题,提出了基于图和子图同构算法的制造特征识别方法。通过提取零件模型中的几何信息与拓扑信息,构造出加权属性邻接图,对零件模型进行精准描述,为建立制造特征库,定义了文件数据的存储结构,结合子图同构算法以及相关判定规则实现对常见制造特征的识别与匹配。以Creo软件中生成的零件模型为例,在VS2010平台中进行二次开发,最后以界面窗口形式展示识别结果,验证了该方法的有效性。