温度场对航空发动机转子超转破裂的影响

CCAR33.27超转适航要求,分析和试验确定的超转转速,必须基于温度和温度梯度的最不利组合。因此,研究温度和温度梯度对超转破裂的影响有非常重要的意义。以某型航空发动机低压6级涡轮转子为例,采用极限应变方法开展了转子部件的超转破裂分析,对比了常温和高温（红线转速对应的温度分布）下转子关键轮盘应变分布趋势和应变增长规律、预测的超转破裂的起始位置和破裂转速等轮盘超转特性;针对超转破裂分析,提出了在高温条件下,经过常温超转破裂试验验证的方法应用的有效性条件。低压涡轮转子的分析结果也显示,红线转速对应的温度状态下,轮盘超转破裂转速比常温下显著降低,而高温下材料屈服强度的大幅降低则是破裂转速下降的主要原因。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

悬臂静子间隙影响的计算分析

悬臂静子在小型涡轮喷气和涡轴发动机的轴流压气机上广泛应用,为了探讨不同条件下悬臂静子间隙的影响,在特定的环境下,分别针对常规负荷和高负荷、小轮毂比和中等轮毂比,组合成几种不同方案,计算分析了静子根部径向间隙分别为弦长的0%、0.25%、0.5%、1%、1.5%和2%情况。计算结果表明:与叶栅中情况类似,在压气机中,悬臂静子同样存在一个特性上表现最优的最佳间隙;在根部未发生角区失速的大流量状态和设计状态,间隙的引入会使得特性恶化,在根部发生角区失速后的小流量状态,间隙的引入则能使得特性变优;间隙形成的泄漏流对角区分离的影响与间隙大小和角区分离程度相关;压气机设计状态负荷水平减小后,间隙的影响规律基本不变;轮毂比增大后,最佳间隙值有减小的趋势。     

基于二阶滑模算法的永磁电机直接转矩控制

针对传统直接转矩控制(DTC)方法低速控制精度差、转矩脉动大、开关频率不稳定等问题,提出了一种基于二阶滑模控制的永磁电机DTC方法。该控制方法基于二阶滑模控制原理,将传统磁链控制器与转矩控制器以滑模控制器替代,对空间电压进行矢量调制,提高了开关频率的稳定性,获得了良好的动态稳定性,改善了电机输出性能。仿真与试验结果表明,该控制方法能够有效减小电流脉动与转矩脉动,同时提高了控制系统的抗干扰能力,实现了电机的快速动态响应,具有较强的鲁棒性能。     

基于马鞍形磁场的永磁直线电机位置解算方法

针对直线电机转子位置检测低成本和较高精度的要求,提出了一种基于马鞍形磁场来获得位置信息的方法及实现过程。分析了永磁体表面的磁场分布特征,指出了利用马鞍形磁场分布曲线来解算位置信息的优点,提出了根据马鞍形磁场推算位置信息的算法流程:先测得错开相位的2条马鞍形曲线数据,划分为4个象限后建立数据库;位置检测时,运用区间搜索算法寻得实际角度所在区间;再根据精度要求,采用合适的插值算法计算得到待解算的角度。仿真结果表明:基于马鞍形磁场的位置解算,能较好地得到直线电机转子的位置信息。     

基于飞行资源分离的航班延误传播研究

在航班串设计及机组排班过程中,经常涉及飞行资源(飞机、机组)分离的问题。而延误航班的飞行资源分离将导致共享资源的衔接航班发生延误,并传播至后续航班串。本文考虑带有飞行资源分离的航班串,利用基于贝叶斯网络的比例风险回归模型,对资源分离后的航班离港延误进行分析。对比两种不同时刻飞机与机组资源分离方案下,各延误因素对衔接航班离港延误,以及整个后续航班串延误时间的影响,结果表明,不同时刻分离方案会造成不同的延误传播效果。本文为飞机、机组资源分离时刻的选择提供了定量分析方法,结果表明,资源分离时刻的不同对衔接航班的离港延误,以及整个后续航班串延误波及时间的影响都不同。     

基于图和子图同构算法的制造特征识别方法

针对传统制造特征难以快速识别的难题,提出了基于图和子图同构算法的制造特征识别方法。通过提取零件模型中的几何信息与拓扑信息,构造出加权属性邻接图,对零件模型进行精准描述,为建立制造特征库,定义了文件数据的存储结构,结合子图同构算法以及相关判定规则实现对常见制造特征的识别与匹配。以Creo软件中生成的零件模型为例,在VS2010平台中进行二次开发,最后以界面窗口形式展示识别结果,验证了该方法的有效性。     

基于无线传感网的纺织机械状态监测系统

提出了一种基于无线传感器网的纺织机械设备监测系统,该系统通过在部署纺织机械上的无线传感器采集数据并传输到基站节点,由基站节点统一对采集数据集中进行分析、处理与展示。详细介绍了系统的体系结构、介质访问控制协议以及系统实现的硬件配置。     

高职院校基建维修管理存在的问题及对策

为了规范基建维修管理,合理控制工程造价,根据多年积累的基建工作管理经验和兄弟院校成功的做法,对高职院校基建维修工程中存在的问题进行了具体分析,提出有效的管理办法和对策。