航空发动机叶片高频模态阻尼的实验测试方法

以NASA Rotor37叶片为对象,研究了航空发动机叶片的高频模态阻尼比的实验测试方法.实验分析和数值计算均说明:在随机声激励下获得频响曲线将包含由支撑结构振动造成的峰值.基于此提出在支撑结构上布置多个传感器的实验方案,并以支撑结构的振动峰值位置和能量相对大小来判定叶片振动主导的振动峰值.用小波阈值收缩法和曲线拟合法对这些振动峰值进行了降噪和模态阻尼比识别,给出了实测模型在10kHz内“叶片主导振动”的模态阻尼比.结果表明:一般的结构金属材料条件下,叶片结构的高频模态阻尼比的数量级小于1%,且随频率增加呈下降趋势.      

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

交会对接任务碰撞规避策略制定研究简

针对交会对接任务目标飞行器与追踪器轨道运行特性,综合考虑规避策略计算方法与工程实际相结合的问题,提出高度规避、时间规避以及与正常轨控相结合的碰撞规避策略计算方法等三种空间目标碰撞规避策略计算方法.高度规避计算方法采用了Lambert飞行原理,用简化二体开普勒模型取代高精度轨道预报方法,迭代求解规避机动速度增量,实现了通过约束过交点与目标径向距离差得到速度增量的最优解;时间规避计算方法通过轨道周期与速度增量的关系,实现了通过约束过交点与目标的时间差得到速度增量的最优解;与正常轨控相结合的碰撞规避策略计算方法,在正常控制考虑冗余控制量的基础上,对控制策略的控制开始时间或沿迹方向的速度增量进行较小的修正,使两者通过碰撞点的时刻或径向距离错开,达到碰撞规避的目的,该方法不仅可以节省燃料、而且对任务的影响较小.通过对三种空间目标碰撞规避策略计算方法仿真分析结果表明,完全适用于交会对接任务,可为我国载人航天任务飞行安全提供技术保障.     

多跑道航班进离场动态调度模型与算法

针对民航运输快速发展导致的航班延误频增现象,研究了多跑道航班进离场的动态调度问题。研究时段内航班的总延误成本最小和延误时间均衡为目标,综合考虑根据机型确定的航班进离场调度优先权和管制员负荷,建立多跑道航班进离场调度模型,利用遗传算法对模型进行仿真验证。仿真结果与先到先服务(FCFS)调度方式进行比较,采用遗传算法的航班进离场调度比FCFS的延误成本降低了45.07%,延误时间降低了37.90%,同时有效地均衡了航空公司的延误时间,保障了航空公司的公平性并提高了跑道系统容量,降低了管制员负荷。通过仿真验证了多跑道航班进离场动态调度策略具有较强的优势和可行性。     

Adaptive Gaussian sum squared-root cubature Kalman filter with split-merge scheme for state estimation

The paper deals with state estimation problem of nonlinear non-Gaussian discrete dynamic systems for improvement of accuracy and consistency. An efficient new algorithm called the adaptive Gaussian-sum square-root cubature Kalman filter（AGSSCKF） with a split-merge scheme is proposed. It is developed based on the squared-root extension of newly introduced cubature Kalman filter（SCKF） and is built within a Gaussian-sum framework. Based on the condition that the probability density functions of process noises and initial state are denoted by a Gaussian sum using optimization method, a bank of SCKF are used as the sub-filters to estimate state of system with the corresponding weights respectively, which is adaptively updated. The new algorithm consists of an adaptive splitting and merging procedure according to a proposed split-decision model based on the nonlinearity degree of measurement. The results of two simulation scenarios（one-dimensional state estimation and bearings-only tracking） show that the proposed filter demonstrates comparable performance to the particle filter with significantly reduced computational cost.     

表面热流可辨识性初步分析

表面热流的可辨识性分析可用于飞行器防热层内温度测量精度和测温点位置的确定,在工程上有较强的实用意义。从无量纲分析和仿真辨识出发,根据防热层材料热物性系数、测点位置、表面热流的频域特性等参数对表面热流辨识结果的影响规律,总结出了表面热流辨识问题的相似参数：基于表面热流频率参数的傅立叶数。此后,以这一傅立叶数为判据,针对不同测量误差值的情况初步建立起了表面热流可辨识性的准则和分析方法。     

Analysis of geometrically nonlinear shells of revolution based on the finite element method with the vector interpolation of desired quantities

In this paper, we present an algorithm for geometrically nonlinear finite element analysis of the shells of revolution. Use is made of the most proper algorithms for vector interpolation of displacements through the nodal unknowns and an efficient algorithm for obtaining the stress-strain increment relation at a step of loading. By comparing the results of analyzing a geometrically nonlinear shell of revolution obtained on the basis of the ANSYS software with the scalar interpolation of displacements with those obtained on the basis of an author-developed finite element, it has been shown that application of the FEM vector displacement interpolation leads to increasing the accuracy of the finite element solutions in analyzing the stress-strain state of the geometrically nonlinear shells.     

柔性接头有效摆心漂移特性

设计了带缠裹式防热套的柔性接头,弹性件和防热套材料均采用硅橡胶.研究了柔性接头有效摆心和几何球心的关系,采用2阶四项式Mooney-Rivlin模型模拟弹性件的本构关系,利用ANSYS软件分别仿真计算柔性接头在压强为0,9MPa下不同摆角条件的有效摆心和几何球心漂移,得到了两者的漂移包络线,把仿真的有效摆心漂移结果与试验测量值进行比较,并利用间隙碰撞试验验证了几何球心漂移仿真结果的准确性,在此基础上研究了有效摆心漂移的原因.结果表明:摆心包络线的仿真结果与试验结果吻合较好,有效摆心和几何球心是两个不同的概念,柔性接头的有效摆心漂移在半径为2.5mm,高为1.4mm的圆柱包络面内,而几何球心的漂移在半径为0.013mm,高为0.6mm的圆柱包络面内,有效摆心漂移是由接头各层增强件和弹性件的变形不同引起的.      

基于空间环境下细胞预处理装置的研制

生物样品的分离纯化是生命科学研究中的重要环节。在常规地面分离方法中,往往用到离心、萃取等操作,然而在空间微重力条件下,常规的方法无法进行,需要采用特定的方法和技术进行研究。以实现空间环境下细胞内生物大分子的分离为目标,研制了一种可以自动化一体化的装置,其先对细胞样品进行清洗、裂解并释放内溶物,然后在超滤分离池中将生物大分子和小分子化合物进行分离。通过对分离获得的大分子物质如蛋白质的回收率来优化仪器装置的最佳运行条件。结果表明,所研制的装置通过泵在一定频率下的切换,可使裂解体系在膜上进行反复的往返振动,从而使裂解液与细胞进行充分的接触,有效提高了细胞裂解的程度,提高了大分子蛋白的回收率,并通过条件优化确定了装置的最佳运行条件。