Analysis of Performance Degradation in CdS Solar Cells

The effect of changes in five physically meaningful parameters on the I-V (current-voltage) curve of a CdS solar cell is calculated. Comparisons between the calculated data and performance data obtained from degraded solar cells are made. The parameter that changed to cause the degradation in each cell becomes apparent.     

Space Radiation Damage Measurements in the Earth Synchronous Orbit

For direct measurement of the integrated radiation dose experienced in Earth synchronous orbit, p-i-n diodes were flown as radiation dosimeters on LES-6. The diode, which has a lifetime of 10-4 seconds in the intrinsic region, was originally developed as a neutron dosimeter, but can detect 1-MeV electron fluences as low as 1013 e·cm-2. Observations over three years in orbit are presented.     

服务网格中面向业务用户的服务组合方法

服务网格环境中如何快速构建组合服务,为业务用户提供快速整合资源、配置集成化应用的平台,按需创建个性化应用,以降低大规模软件开发的成本、提高效率,成为了服务网格领域亟待解决的一个问题。提出了一种服务网格环境中面向业务用户的服务组合方法,它通过服务映射机制实现从业务用户所熟悉的业务服务到具体物理服务的映射;利用基于上下文的流程推导技术实现了组合业务服务流程向组合物理服务流程的映射;利用物理服务选取技术,生成能够最大限度满足用户需要的组合服务。研究表明该方法应用的原型系统,适用于普通业务用户,能够提高组合物理服务流程构建的效率。     

高温超导磁悬浮助推缩比试验系统动态测试分析

基于磁悬浮助推技术概念研究方案建立了一套悬浮加速缩比试验系统.从整体缩比模型振动试验出发,主要研究悬浮质量以及悬浮刚度对整体系统动态性能的影响,并在进行缩比单元动态试验结论的基础上,建立试验模型的加速试验动态采集系统,对整体模型进行运行性能试验.在试验基础上提出了提高磁悬浮推进系统运行稳定性的依据,并据此提出相应可行的解决方案设想.通过模型加速试验并采集试验数据定性分析磁浮系统的综合运动性能,以更好地评估系统稳定特性和品质,也为进一步研究磁悬浮助推发射的气动、分离系统稳定性和可靠性提供参考.     

摆盘流动与换热性能数值仿真

针对受燃烧室出口高温燃气冲刷的摆盘装置的冷却水回路,建立二维、三维物理仿真模型,模拟了冷却水在内部流道的 流动与换热过程,考察了冷却水进口压力、冷却水流量对流阻和换热性能的影响.结果表明:①摆盘冷却水进口压力由2.3×105Pa提高到8.3×105Pa,摆盘壁温变化微小,结构1壁温升高5K,结构2壁温升高7K;②冷却水进口速度由0.5m/s提高到5.3m/s,结构1壁温降低约120K,结构2壁温降低约100K,冷却效果明显;③结构2通过缩小流道的流通面积,能在更小的冷却水流量的工况下得到更好的换热效果.      

航空发动机叶片高频模态阻尼的实验测试方法

以NASA Rotor37叶片为对象,研究了航空发动机叶片的高频模态阻尼比的实验测试方法.实验分析和数值计算均说明:在随机声激励下获得频响曲线将包含由支撑结构振动造成的峰值.基于此提出在支撑结构上布置多个传感器的实验方案,并以支撑结构的振动峰值位置和能量相对大小来判定叶片振动主导的振动峰值.用小波阈值收缩法和曲线拟合法对这些振动峰值进行了降噪和模态阻尼比识别,给出了实测模型在10kHz内“叶片主导振动”的模态阻尼比.结果表明:一般的结构金属材料条件下,叶片结构的高频模态阻尼比的数量级小于1%,且随频率增加呈下降趋势.      

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

交会对接任务碰撞规避策略制定研究简

针对交会对接任务目标飞行器与追踪器轨道运行特性,综合考虑规避策略计算方法与工程实际相结合的问题,提出高度规避、时间规避以及与正常轨控相结合的碰撞规避策略计算方法等三种空间目标碰撞规避策略计算方法.高度规避计算方法采用了Lambert飞行原理,用简化二体开普勒模型取代高精度轨道预报方法,迭代求解规避机动速度增量,实现了通过约束过交点与目标径向距离差得到速度增量的最优解;时间规避计算方法通过轨道周期与速度增量的关系,实现了通过约束过交点与目标的时间差得到速度增量的最优解;与正常轨控相结合的碰撞规避策略计算方法,在正常控制考虑冗余控制量的基础上,对控制策略的控制开始时间或沿迹方向的速度增量进行较小的修正,使两者通过碰撞点的时刻或径向距离错开,达到碰撞规避的目的,该方法不仅可以节省燃料、而且对任务的影响较小.通过对三种空间目标碰撞规避策略计算方法仿真分析结果表明,完全适用于交会对接任务,可为我国载人航天任务飞行安全提供技术保障.