石英陶瓷与碳纤维增强复合材料间胶接增强的优化工艺

为提高硅橡胶胶黏剂胶接石英陶瓷和碳纤维增强复合材料的强度和耐温性能,研究了胶接面湿热状态、打磨程度、胶层厚度、操作等待时间等工艺参数对胶接强度的影响。在试片正常烘干、打磨的情况下,当胶层厚度为0.4 mm、操作等待时间小于0.5 h时,胶接效果最优,其压缩剪切强度达到了3.06 MPa。探索了底涂剂处理对胶接强度和耐温性能的影响。在温度不高于100℃时,底涂剂A的效果较好。经底涂剂A处理后,胶接试片常温下的强度提高了13.7%,达到3.48 MPa;100℃时的强度提升率达到37.7%。在更高温度下,底涂剂B的效果更为显著。经底涂剂B处理后,胶接试片常温下的强度提升了10.1%,达到3.37 MPa;300℃时的强度提升了44.0%,达到1.57 MPa;200℃时的强度提升率最高,为49.0%。测试结果为高温条件下石英陶瓷胶接结构的胶接工艺优化及其应用提供了参考。     

Command filtered sliding mode trajectory tracking control for unmanned airships based on RBFNN approximation

This paper presents two sliding mode controllers to address the trajectory tracking problem of unmanned airships in the presence of unknown wind disturbance. The sliding mode controller proposed first is designed by a fast power rate reaching law(FPRRL). The disturbance is compensated by a radial basis function neural network (RBFNN). To avoid the aggressive adaptation, the controller is augmented by a command filter. The controller provides good robustness and tracking performance with no chattering under the hypothesis of ideal wind field. However, serious chattering occurs when simulation is performed under discontinuous wind field. To simulate the wind in practice, the wind field employed in the simulation is generated by the combination of a constant field and white noise. The controller is improved subsequently with an extended model to suppress the chattering induced by the white noise. The enhanced controller manipulates the derivation of system input, thus attenuating the chattering. Stability analysis shows that both controllers drive the tracking error into a controllable small region near zero. Simulations are provided to validate the performance of the proposed controllers under different wind hypothesis.     

轴段可调节式双转子结构动力特性模拟试验台设计与优化

为了解航空发动机双转子的动力学特性，搭建了轴段可调节式双转子结构动力特性模拟试验台，其主要包括高速电机、 低压转子、高压转子、模拟盘、支架、齿轮箱、基座等。采用有限元法和变换哈默斯利算法相结合的联合仿真方法，对试验台进行了 临界转速的计算及优化；计算了双转子系统的稳态不平衡响应，分析了临界转速变化对转子系统振动特性的影响。结果表明：优 化后试验台前4阶临界转速与原型机实测临界转速的误差在5%以内，试验台能较好的模拟原型机动力学特性；优化后各轴承处 最大响应幅值中的最大值明显减小，试验台具有良好的振动特性。     

某型飞机滑跃起飞性能仿真分析

介绍了滑跃起飞的原理和运动特点,描述了滑跃起飞的关键数学模型。以某型飞机为例,计算了不同构型下飞机的起飞性能。最后分析了滑跑距离、起飞重量和杆配平量对滑跃起飞性能的影响,并结合试飞数据给出相关结论。     

MANEUVERING TARGET TRACKING USING FUZZY COMPENSATOR

Ｔｈｅｍａｎｅｕｖｅｒｉｎｇｔａｒｇｅｔｓｔｒａｊｅｃｔｏｒｙｅｓｔｉｍａｔｉｏｎｐｒｏｂｌｅｍｈａｓｂｅｎａｎｉｍｐｏｒｔａｎｔｔｏｐｉｃａｎｄｍａｎｙｆｒｕｉｔｆｕｌｒｅｓｕｌｔｓｈａｖｅｂｅｅｎａｔａｉｎｅｄ．Ｉｔｉｓｂｏｔｈｔｈｅｋｅｙａｎ...     

直升机金属结构缺陷容限验证技术研究

直升机结构的缺陷容限验证在FAR／CCAR27／29．571条适航条款中有明确的要求。文章提出了全尺寸结构缺陷容限验证思路，对验证的各个环节，包含缺陷的类型及参数、缺陷容限特性曲线基本参数及安全系数、真实缺陷下载荷或应力的修正、结构的缺陷容限性能、检查周期的确定等进行了探讨，为开展直升机结构缺陷容限验证工作提供了技术支持。     

Nostoc sphaeroides Kützing,an excellent candidate producer for CELSS

Some phytoplankton can be regarded as possible candidates in the establishment of Controlled Ecological Life Support System (CELSS) for some intrinsic characteristics, the first characteristic is that they should grow rapidly, secondly, they should be able to endure some stress factors and develop some corresponding adaptive strategies; also it is very important that they could provide food rich in nutritious protein and vitamins for the crew; the last but not the least is they can also fulfill the other main functions of CELSS, including supplying oxygen, removing carbon dioxide and recycling the metabolic waste. According to these characteristics, Nostoc sphaeroides, a potential healthy food in China, was selected as the potential producer in CELSS. It was found that the oxygen average evolution rate of this algae is about 150 μmol O₂ mg⁻¹ h⁻¹, and the size of them are ranged from 2 to 20 mm. Also it can be cultured with high population density, which indicated that the potential productivity of Nostoc sphaeroides is higher than other algae in limited volume. We measured the nutrient contents of the cyanobacterium and concluded it was a good food for the crew. Based on above advantages, Nostoc sphaeroides was assumed to a suitable phytoplankton for the establishment of Controlled Ecological Life Support System. We plan to develop suitable bioreactor with the cyanobacterium for supplying oxygen and food in future space missions.     

遗传算法在薄壁件装夹位置优化中的应用

针对航空接头类薄壁件,采用遗传算法和有限元法相结合的优化方法,提出以加工过程中零件平均应力最小为目标函数,建立工件装夹优化模型。该方法优化后所得平均应力与实验所得数据基本一致,验证了这是一种有效的夹具装夹优化方法,对改善加工变形提供了可靠依据。     

加速度计温控系统被控对象建模技术研究

加速度计工作过程中,其内部与外界环境存在温度梯度,针对温度变化影响加速度计参数的问题,提出了一种加速度计温控系统被控对象建模的方法。进行了多工作点加速度计升温和降温试验,采用递推增广最小二乘法对被控对象模型进行了辨识,建立了加速度计温控系统被控对象模型和降温模型,计算结果表明,3min后温控系统被控对象模型曲线残差在-0.5~0.5℃之间,降温模型曲线残差在-0.15~0.15℃之间,满足系统对加速度计性能需求,表明了方法的有效性。     

镀银抗硫防变色性能研究

介绍防止零件镀银层变色的试验过程，包括工艺配方、试片准备及钝化工艺等。