基于粒子群算法的电帆轨迹优化设计

电帆是一种利用太阳风动量的新颖的无工质空间推进系统,文章研究了以电帆为对象的行星际转移轨迹优化问题。以地球轨道转移到火星、金星轨道为任务对象,采用连续推力模型,研究极坐标系下最小时间转移轨迹优化设计问题。提出了两种基于粒子群算法(PSO)的直接优化方法,避免对协态变量初值敏感的两点边值问题（TPBVP）求解。方法一是通过打靶法直接离散化控制量输入,将最优控制问题转化为非线性规划参数优化问题,采用PSO算法寻优,获得近似最优的转移轨迹。方法二是针对任何连续控制律曲线都能以一定精度的多项式函数进行曲线拟合的特性,设计逼近最优转移轨迹控制律的多项式函数,通过PSO算法优化多项式函数参数获得逼近最优解的转移轨迹。仿真结果表明采用上述两种方法进行转移轨迹优化设计,具有随机猜测初值、全局收敛、鲁棒性强的特点。     

地基伪卫星系统多址测距误差的校正算法

相对于卫星导航,地基伪卫星与接收机距离较近,测距中不涉及电离层传播等误差,易实现高精度测距和定位。但由于地基伪卫星位置固定,在信号连续发射模式下伪卫星信号间的多址干扰(MAI)会引起相对恒定的测距误差,针对地基伪卫星系统这一特点,提出一种基于反馈串行干扰抵消(SIC)的测距算法。首先对全部伪卫星信号进行捕获跟踪和功率估计,然后通过串行干扰抵消算法降低强功率伪卫星信号对期望测距信号的干扰,通过反馈模式进一步提高干扰抵消算法的性能。仿真结果表明,该方法可有效改善地基伪卫星系统强远近效应区域内的测距性能,不考虑其他误差下在强远近效应区域内基于码环可将伪卫星测距性能从10 m以上降低到约0.3 m。     

热效应布局下的缓冲器插入时序优化方法

随着集成电路的集成度越来越高,芯片的发热量越来越大且其内部温度呈不均匀分布,这会影响关键路径的传播延时,进而影响基于缓冲器插入的关键路径性能.提出了一种考虑芯片热效应布局优化的缓冲器插入时序优化方法,在版图设计的早期估计芯片的热分布和温度分布并且把其应用到版图布局优化和RC延时模型中.同时利用模拟退火算法基于热分布调整并优化布局,最后在最优布局下利用提出的缓冲器插入模型和快速插入算法进行时序优化.仿真结果表明相对于不考虑温度效应布局优化的缓冲器插入方法,缓冲器插入延时优化方法能有效降低最坏延时和缓冲器插入数目,最坏延时比传统方法降低9%~18%,比文献已经提出的最好方法降低5%~7%,缓冲器插入数比其少10~20个.      

超声速尾迹-剪切流的混合增强

超声速条件下燃料和空气之间的高效混合是超然冲压发动机技术上的主要挑战。基于大涡模拟和流动稳定性分析,针对超声速尾迹-剪切流动开展了混合增强方法研究。尾迹的存在改变了混合层流动的速度剖面,对流动稳定性产生了重要影响,使混合层由三维最不稳定变为二维最不稳定,最不稳定扰动波频率和增长率增大。基于流动稳定性结果引入扰动的混合增强方式依然有效,根据稳定性结果设计了波纹隔板。数值结果表明：二维波纹壁引入的扰动未能增长,不具备混合强化效果,而三维波纹壁引入的扰动能够快速增长,具有混合强化效果,且波纹壁参数越接近最不稳定扰动波参数,混合强化效果越明显。     

叠层穿刺CF/Al复合材料准静态拉伸力学行为与失效机制

针对新型的叠层穿刺碳纤维织物增强铝基复合材料（CF/Al复合材料）,通过细观力学数值模拟与实验结合的方法研究了其在准静态拉伸载荷作用下的渐进损伤与断裂力学行为。复合材料经向拉伸弹性模量、极限强度与断裂应变的实验结果分别为129.61 GPa、630.14 MPa和0.75%,细观力学模型预测误差分别为-9.41%、7.57%和1.33%,均匀化计算的宏观应力-应变曲线与实验曲线总体上相符。经向拉伸变形初期首先出现经/纬纱交织处基体合金的局部损伤,随着拉伸应变量的增大依次发生纬纱和穿刺纱的横向开裂,拉伸变形后期基体合金与经纱失效引起宏观应力-应变曲线的急剧下降,复合材料拉伸断口表现为经纱轴向断裂及纬纱和穿刺纱横向开裂共存的形貌特征,纤维拔出和基体断裂导致的经纱轴向断裂是诱发复合材料最终失效的主要机制。     

星地动态双向时间同步与测距算法

针对卫星运动对星地距离和钟差测量的不利影响,提出一种基于最小二乘拟合的星地动态双向时间同步与测距算法。在建立星地可视模型基础上,仿真了MEO运动卫星与地面时间同步站之间星地距离的变化规律,分析了卫星运动对星地双向时间同步与测距的主要不利影响。该算法首先利用星地双向时间同步数据分别生成星地距离和钟差拟合多项式,然后联合求解出运动卫星误差最小的星地距离与钟差。实验结果表明了该算法的合理性和科学性,在包含仿真误差的条件下,其时间同步精度优于3ns,测距精度优于3m。将其应用到各种空天应用系统的星地时间同步与测距中,可以消除卫星运动对双向时间同步与测距的不利影响,提高时间同步与测距精度。     

采用改进非支配近邻免疫算法的低轨混合星座设计优化

针对低轨同构星座覆盖资源在纬度上分布不均匀的不足,提出采用低轨混合星座提升覆盖均匀性的设计方案,并推导了满足全球任意点平均每天覆盖一定次数的最小卫星规模估算公式。针对非支配近邻免疫算法（NNIA）约束处理方面的不足,提出基于约束支配的改进非支配近邻免疫算法（Modified NNIA）,并以此设计了一种低轨混合星座优化平台来优化带约束的星座设计问题。仿真结果表明,改进的NNIA算法在收敛速度和多样性上均优于非支配分层遗传算法（NSGA II）和多目标粒子群算法（MOPSO）,可大大提高星座设计的效率。同时优化结果也表明低轨混合星座可提高覆盖的均匀性和大部分区域的覆盖次数,进而减少特定覆盖要求所需的卫星数目。     

Numerical investigation of the impact of asymmetric fuel injection on shock train characteristics

Numerical simulations are carried out to investigate the impact of asymmetric fuel injection on shock train characteristics using the commercial-code FLUENT. The asymmetry of fuel injection is examined by changing the fuel flow rates of the upper and lower wall fuel injectors. The numerical approach solves the two-dimensional Reynolds-averaged Navier–Stokes (RANS) equations, supplemented with a k-ω model of turbulence. As a result, different ways of fuel injections will always lead to shock train transitions, with the variations of shock train structure, strength and leading edge position. For symmetric fuel injection, the flowfield of the isolator is quite asymmetric with the boundary layer of the upper wall side developing much stronger than that of the lower wall, which is due to the heterogeneity of the incoming flow. Regarding to asymmetric fuel injection with more of lower wall side, though the pressures in the combustor are nearly the same, the first shock of the shock train converts between ‘Distinct symmetric X type shock’ and ‘Obscure and weaker asymmetric shock’ and the shock train leading edge moves upstream with the increase of the asymmetry level. With regard to asymmetric fuel injection with more of upper wall side, ‘incomplete asymmetric X type shock’ occurs and the shock train structures keep nearly the same with low level of fuel injection asymmetry. Unexpected results like unstart will happen when increasing the level of fuel injection asymmetry. And the isolator will come back to normal state by decreasing the differential of upper and lower wall sides fuel injections.     

Experimental study of a flush wall scramjet combustor equipped with strut/wall fuel injection

In this study a flush wall scramjet combustor is tested in a supersonic incoming air flow with the Mach number of 3 which is generated by an air vitiation heater producing the stagnation temperature of 1505 K. Using liquid kerosene as the fuel, the flame is stabilized by means of a centrally mounted O₂ pilot strut after being ignited by a plasma torch. During experimental measurements, the fuel is injected with a constant equivalence ratio of 0.8 according to specified strut/wall injection ratios, i.e., a portion of the fuel amount is injected from the strut while the rest is injected from the wall. The strut and wall injectors are arranged at the same axial position. The combustion performance and wall temperature gradients are evaluated with various fuel feeding ratios between the wall and the strut. Experimental results show, when the equivalence ratio is constant and the axial injection position is fixed, the combustion characteristics vary significantly with the strut/wall fuel feeding ratio, especially when this ratio is close to its lowest and highest limits. Among the four fuel feeding ratios examined, the strut only injection mode and the average distributed strut/wall injection mode show the best combustion performance. However, the strut/wall injection mode produces a smaller wall temperature gradient compared to the strut only injection mode, which is due to the significant film cooling effect caused by the wall injected liquid kerosene.