应用加权中值滤波法检测薄壁梁式挠性器件下摆量

应用加权中值滤波法对薄壁梁式挠性器件下摆量进行高准确度CCD检测。薄壁梁式挠性器件在测量过程中测量图像存在高频抖动现象,因此测量准确度不高,运用加权中值滤波后使用最小二乘法细分技术,可以在实现提高测量准确度的同时,消除高频抖动带来的误差,从而可以有效提高CCD测量薄壁梁式挠性器件下摆量的准确度。实验表明,该方法比传统测量方法准确度提高20倍以上。     

快速预热型铷原子振荡器的研制

介绍了一种快速预热型铷原子振荡器的设计方法和试验数据 ,3 5min的锁定时间、0 4 5L的小巧体积和良好的频率重现性能 ,非常适合于战术应用。     

利用MF雷达对耀斑期间电离层D区电子密度的观测研究

利用MF雷达观测资料对X级别耀斑爆发期间在66-80km高度之间的电子密度进行了研究，观测到了耀斑爆发期间电子密度的突然增加，在较低高度上的电子密度的时间变化趋势与耀斑的软X射线辐射通量相关．电子密度的变化强度依赖于具体的耀斑参数，有些耀斑引起的电子密度增加高达400cm^-3，有些仅为100cm^-3左右．但耀斑期间在这一高度区间增加的总电子含量增量仅占耀斑辐射引起的整个电离层总电子含量增量的千分之一左右．最后，利用恢复阶段电子密度的时间变化过程估算了1997年11月4日耀斑期间部分高度上的有效复合系数．     

亚、超音速机翼非定常广义气动力系数之间的关系

 <正> 研究弹性飞机的动力学特性应计及非定常广义气动力。为了尽可能保留非定常运动历程,应首先计算由阶跃函数形式下洗产生的非定常气动力函数(指示函数或指数函数),再利用卷积形式的迭加原理处理任意函数形式下洗产生的非定常气动力。用振型法建立飞机弹性运动方程,可将飞机上任一质点的弹性位移近似地表示为     

飞机壁板结构的声疲劳计算及试验

 <正> 飞机结构所承受的噪声载荷声压级超过130dB时,经较长时间激励,往往在噪声诱导应力较大的区域里产生疲劳破坏。而在各种类型的结构件中声疲劳破坏的相对发生率以蒙皮壁板结构为最高。 本文采用矩形铝合金平板来模拟蒙皮壁板结构,对其进行了声疲劳寿命计算与试验研究.     

喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

微量气味成分的自由基簇射技术脱除

研究了密闭体系中微量气味污染物的脱除作用与机理。采用电晕放电自由基簇射技术，实现了人工环境下氧化性自由基的产生；以电子自旋共振技术（ESR）对气态羟基自由基实施了捕集和检测，验证了在羟基自由基的存在下NH3被氧化为N2。通过U—I获得反应能耗和污染物去除效率为：NH3脱除效率为90．6％时，能耗1．0W。研究表明：自由基簇射技术产生的氧化性自由基可有效去除密闭生存环境中产生的NH3等微量有害气味成分，将在空间站等密闭生存系统内空气净化中有很好的应用前景。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Suggestion for aircraft flying qualities requirements of a short-range air combat mission

Owing to the lack of a direct link with the operations in short-range air combat,conventional aircraft flying qualities criteria are inappropriate to guide the design of a task-tailored flight control law.By applying the mission-oriented flying qualities evaluation approach,various aircraft with different control law parameters are evaluated on a ground-based simulator.This paper compares the evaluation results with several conventional flying qualities criteria,and discusses the appropriate parameter combination to reflect the flying qualities requirements of short-range air combat,The comparison and analysis show that a short-range air combat mission requires a higher minimum short period mode natural frequency and a smaller maximum roll mode time constant,and allows a lower minimum pitch attitude bandwidth and a higher maximum short period mode damp ratio than those of conventional flying qualities criteria.Furthermore,a combination of the pitch attitude bandwidth,the pitch attitude magnitude at the bandwidth frequency,and the pitch attitude transfer function gain can define the flying qualities requirements of short-range air com bat.The new metric can successfully predict the flying quality levels of aircraft in a short-range air combat mission.