基于双变量预测控制的表贴式永磁同步电机直接转矩控制系统

基于电压矢量幅值和相角为变量的表贴式永磁同步电机(SPMSM)定子磁链幅值和转矩表达式,给出了9个不同幅值和相角的备选电压矢量,采用预测控制计算得出施加不同电压矢量下一时刻的定子磁链幅值和转矩值,建立了基于磁链和转矩误差的目标函数,并选择使目标函数最小的电压矢量为作为下一时刻施加的最优电压矢量。仿真结果表明:在双变量预测控制下,SPMSM直接转矩控制系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。进一步对比分析表明:与开关表和固定电压矢量选择策略相比,双变量预测控制能显著减小转矩和磁链脉动。与开关表相比,转矩脉动均方根误差降低了62.92%,磁链脉动均方根误差降低了45.05%,评价函数均值降低了60.30%;与固定电压矢量选择策略相比,转矩脉动均方根误差降低了22.40%,磁链脉动均方根误差降低了3.85%,评价函数均值降低了15.93%。     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

真实气体效应对Ma10级进气道流动的影响

为了探究高马赫数超燃冲压发动机高速飞行时真实气体效应对进气道流场的影响,仿真获得了不同气体模型下Ma10级进气道流场结构和性能。结果表明:进气道主流流场温度较低,不足以触发空气的离解反应,反应仅发生在边界层内,但反应程度较低,远未达到化学平衡状态,除了边界层温度及热载荷特性,其流场结果则更为贴近冻结流流场,因而化学非平衡模型与热完全气体模型的进气道通流流场结构和性能基本一致。而真实气体效应导致边界层特性的不同,对进气道起动特性产生影响,吸热离解反应通过对进口分离包的抑制和增大进口马赫数将进气道的再起动马赫数从9.8降低到9.4。在对进气道在宽速域应用中的钝化设计研究发现,真实气体效应虽然对前缘钝化进气道流场的压力分布和性能无明显影响,但是其能起到整体降低壁面热流的作用,不仅钝头处的热流降低了1MW/m2,通道内的热流也整体降低了0.1MW/m2。     

稳态与瞬态冲击射流换热性能实验对比

为了对比研究稳态与瞬态单孔冲击射流的传热性能,采用热色液晶测温技术获取实验件被冲击表面的传热系数分布。实验中改变了冲击雷诺数Re和冲击孔直径比L/d,利用工业相机拍摄实验件凹表面颜色变化过程,计算并对比两种射流条件下局部努塞尔数Nu_D的分布,并与文献值进行比较。研究表明相对于稳态冲击射流,瞬态冲击射流的传热性能更佳。通过记录整个冲击射流过程,得到Nu_D随时间t变化关系。驻点附近NuD随冲击的进行逐渐减小并趋于稳定。随冲击雷诺数Re增大或冲击孔直径比L/d接近6,瞬态冲击射流的强化传热效果逐渐明显,强化效果可达15%以上。     

风洞试验绳牵引冗余并联机器人的刚度增强与运动控制

 以一种应用于低速风洞试验的6自由度绳牵引冗余并联机器人为研究对象,解决飞行器模型在风荷作用下动态定位误差大、力学测量精度不高的问题。运用微分变换推导了该机器人的刚度解析表达式;分别建立了末端执行器和驱动系统的动力学模型;针对系统冗余驱动、强耦合和非线性的特点,设计了基于刚度增强准则的关节空间比例微分（PD）修正前馈控制器,实现了以提高飞行器升力方向、顺风向和俯仰转动方向刚度为目标的绳系张力优化分配。数值仿真算例表明,与基于张力极小准则的控制器相比,前者有效地提高了飞行器的动态定位精度。     

处理机匣对高压压气机性能和稳定性影响的数值模拟和试验研究

本文主要采用数值模拟和试验验证的方法探索轴向斜槽处理机匣改善高压压气机尖部流动情况及扩大压气机稳定工作边界的基本原理。采用Numeca CFD软件对某多级高压压气机第一级叶尖间隙流场和具有轴向斜槽处理结构的流场进行非定常计算．并对计算结果进行对比、分析,详细揭示了叶栅顶部间隙区及处理槽内的流动特征。数值计算结果显示,轴向斜槽处理机匣能够衰减或是消除叶尖的泄漏涡,推迟失速的发生。处理机匣对压气机性能的影响并不是直接采用对泄漏涡的干涉,而是通过叶尖附近气流在高压作用下从压力面尾缘进入斜槽,而后气流在叶背前缘以高速由斜槽射入主流。该高速射流能有效地扫除叶尖易失速的附面层,从而延迟气流分离,扩大压气机的失速裕度并减少二次流损失。试验结果显示,该多级压气机采用轴向斜槽处理机匣有效地减少了尖部气流泄漏,扩大了压气机稳定工作范围。     

基于鲁棒变结构控制方法的非线性导弹自动驾驶仪设计

对一类非线性不确定导弹控制系统,采用自适应方法进行了基于滑模理论的变结构控制器设计。该方案使得采用反演手段产生的微分爆炸问题得到较好的回避,同时构造自适应律,消除了不确定性对系统的影响,最后通过构造Lyapunov函数方法,确保了系统的鲁棒稳定性。文末仿真结果表明了该方案的有效性。     

窄带信号小样本谱估计算法

针对窄带平稳随机信号的小样本谱估计问题,结合均匀线性阵列的空间谱估计算法,提出了一种高性能小样本谱估计算法。该算法首先利用采样数据构造一个Toeplitz矩阵;然后对该矩阵进行特征值分解得到信号子空间和噪声子空间;再结合MUSIC、ESPRIT等子空间算法,即可实现对小样本采样数据的谱估计。数值仿真验证了该算法的有效性。     

模式识别中幂变换正态性的研究

在基于模板匹配的模式识别中,当数据呈正态分布时得到的识别效果最优。幂变换是一种将非正态分布转换为正态分布的一种有效方法,文中对幂变换技术的正态性问题进行了相关的研究,并探讨了典型分布条件下的幂变换最佳取值问题,为幂变换的应用提供了一定的理论基础。