燃烧室头部进气规律对煤粉燃烧效率的影响

用实验方法研究了火焰筒式煤粉燃烧室头部进气规律对燃烧效率的影响。通过对6种结构的头部配气方案的分析比较,得出了煤粉燃烧室合理的头部配气方案,为今后煤粉燃烧室的设计和工作状态的选择提供了重要的实验依据。     

基于SPCE061A数字语音温度控制系统的设计

以凌阳SPCE061A单片机为控制核心,设计并制作了一款具有温度设定灵活、数字显示及语言播报功能的水温控制器,通过PID控制算法产生脉宽调制波,提高了控制精度。实践表明:该水温控制器达到了设计要求,有一定的实用开发价值。     

建立腔体热释电探测器相对光谱响应度标尺的研究

由于腔体热释电探测器在宽光谱范围内具有相对平坦的光谱响应度,因此经常被用作标定探测器相对光谱响应度的工作基准。但是在标定过程中通常认为腔体热释电探测器是无光谱选择性的,即R(λ)为常数。这样就会使测量结果不够准确,因此建立腔体热释电探测器相对光谱响应度的标尺是非常重要的。本文主要介绍了建立腔体热释电探测器相对光谱响应度标尺的原理和方法,并通过实验利用该方法建立了腔体热释电探测器相对光谱响应度的标尺,从而使该腔体热释电探测器成为红外光谱响应度测量装置的工作基准。     

基于层次分析法的飞行模拟训练评价体系设计

为科学完善地描述飞行模拟训练中的应急处置程序,提升飞行员专业驾驶技术水平,本文提出飞行模拟训练评价体系,并通过层次分析法构造3阶判断矩阵,检测矩阵一致性指标为0.037,具有可接受性;并采用关联度进行数据分析量化计算,为飞行训练考核标准奠定理论基础。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

甲醇超临界水完全气化制氢系统的火用分析

基于热力学火用平衡方程所揭示的实际用能过程和理想用能过程,通过引入"偏离值"、"偏离度"两个指标,对甲醇超临界水制氢系统进行了火用分析。首先确定了加热和反应环节为重点优化环节;然后研究了此二环节的"偏离度"分别随压力、温度的变化规律,并比较了压力和温度对"偏离度"的影响作用大小。在提高甲醇制氢系统的能质利用率方面进行了有益的探讨,其结论对制氢系统的节能工作具有一定的参考价值。     

可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.