空间推进器制造中的可破坏性工装

由于航天研究的特殊性,其预研型号零件一般批量很小,并且有许多零件不易装夹。选用一种不同于传统专用工装的可破坏性工装,其材料可以是金属的,也可以是非金属的。为保证进度,必须建立预先性的可破坏性工装的数据库。采用可破坏性工装缩短了研制周期,降低了研制成本。     

用FTIR光谱仪测量排气系统中红外光谱辐射强度的方法

通过理论分析及实验研究讨论了傅立叶变换红外(FTIR)光谱仪测量排气系统中红外光谱辐射强度过程中误差产生的原因, 设计了一套简易有效的测量方法.用此方法测量了黑体和热喷流的光谱辐射强度.结果表明:该测量方法能够有效地获得排气系统的中红外光谱辐射强度, 具有工程实用价值.      

基于遗传算法和空间推进方法的单壁扩张喷管优化设计研究

 将单目标遗传算法和多目标遗传算法（包括NSGA-II和NCGA）,与高效、高精度的空间推进流场数值模拟方法——SSPNS方法相结合,对二维超燃冲压发动机尾喷管即单壁扩张喷管（SERN）进行了气动优化设计研究。在巡航点（Ma=6.0）讨论了推力系数C_T最大单目标模型,推力系数C_T最大升力系数C_L最大两目标模型,以及推力系数C_T最大升力系数C_L最大俯仰力矩系数C_m最小三目标模型,分别得到了喷管的最大推力设计和关于多个目标性能的Pareto最优前沿。结果表明,扩张壁初始扩张角θ_r,i和外罩长度L_c对C_T影响较大;较小的L_c和较大的θ_r,i设计,将降低外罩内表面的负升力作用而使得SERN的C_L较大;较长外罩和较小的θ_r,i,对应Pareto最优设计的C_M较小。     

Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

In order to improve the navigation accuracy of an inertial navigation system （INS）, composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data （UFCL for short） method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system （MEMS） gyroscope＇s zero drift.     

转发式干扰下GPS定位精度的仿真分析

根据GPS转发式干扰的原理,建立了转发式干扰对GPS定位精度影响的数学模型.讨论了两种转发式干扰模式对定位的影响.最后通过计算机仿真分析得出了GPS转发式干扰对GPS定位精度影响的相关结论.     

基于CFAR检测的SAR噪声干扰效果评估方法

在研究美国林肯实验室的SAR恒虚警(CFAR)自动目标检测方法的基础上,分析了CFAR目标检测技术在不同噪声干扰强度下检测概率的变化情况,并结合图像相关性分析得出一种改进的基于CFAR检测技术的SAR噪声干扰效果评估方法.     

空空导弹惯性开关中圆周磁场对导弹性能的影响

为了提高空空导弹的作战效能和可靠性,由弹载电源向开关电路进行大电流放电,可提高惯性开关中圆柱电极上周磁场的强度,增强抵抗磁钢对钢珠反向作用力的能力,当导弹撞击目标过载较小时,使惯性开关的导通时间也能够满足触发电路工作需要,因此,导弹遇目标不炸的故障概率可得到下降。     

电大目标等离子体隐身的矩量法优化设计

根据高频散射特征,提出典型几何散射中心替代法,用于解决矩量法（MOM）用于电大目标等离子体隐身时的优化设计问题。以某典型电大目标为例,通过仿真分析了该方法的可行性。结果显示,电大目标覆盖利用该方法得到最优参数的等离子体后,不仅目标整体的单站RCS平均缩减与典型几何散射体的单站RCS缩减相当,且任意方向上RCS基本都有10dB左右的缩减,表明用该方法得到用于电大目标隐身的等离子体参数是可行的。     

大直径铝合金铆钉以铆代螺可行性试验研究

针对双层铝合金板铆接结构,通过电磁铆接工艺试验,分析Φ10mm-2A10铝合金铆钉镦头的微观组织,与钢质螺栓连接接头对比评价了铆接接头的力学性能。研究发现,随放电电压的增加,铆钉镦头直径逐渐增加、高度逐渐降低。铆钉镦头以绝热剪切为主要变形模式。铆接接头的最大剪切和拉脱载荷分别为23.3k N和35.0k N,均高于钢质螺栓连接接头,并且相对于螺接接头可减重15.8%。     

Eliminating negative VTEC in global ionosphere maps using inequality-constrained least squares

Currently, ground-based Global Navigation Satellite System (GNSS) stations of the International GNSS Service (IGS) are distributed unevenly around the world. Most of them are located on the mainland, while only a small part of them are scattered on some islands in the oceans. As a consequence, many unreasonable zero values (in fact negative values) appear in Vertical Total Electron Content (VTEC) of European Space Agency (ESA) and Center for Orbit Determination in Europe (CODE) IONEX products, especially in 2008 and 2009 when the solar activities were rather quiet. To improve this situation, we directly implement non-negative physical constraints of ionosphere for global ionosphere maps (GIM) with spherical harmonic functions. Mathematically, we propose an inequality-constrained least squares method by imposing non-negative inequality constraints in the areas where negative VTEC values may occur to reconstruct GIM models. We then apply the new method to process the IGS data in 2008. The results have shown that the new algorithm efficiently eliminates the unwanted behavior of negative VTEC values, which could otherwise often be seen in the current CODE and ESA GIM products in both middle and high latitude areas of the Southern Hemisphere (45°S∼90°S) and the Northern Hemisphere (50°N∼90°N). About 64% of GPS receivers’ DCBs have been significantly improved. Finally, we compare the GIM results between with and without the inequality constraints, which has clearly shown that the GIM result with inequality constraints is significantly better than that without the inequality constraints. The inequality-constrained GIM result is also highly consistent with the final IGS products in terms of root mean squared (RMS) and mean VTEC.