细晶铸造对K418合金拉伸性能的影响

测试了不同温度下细晶铸造和普通铸造Ｋ４１８合金的拉伸性能。结果表明，细晶铸造明显改善了合金的极限位伸强度和屈服强度，室温和６００℃的合金拉伸强度和晶粒平均直径符合Ｈａｌｌ－Ｐｅｔｃｈ关系。     

H2O2-PE固液火箭发动机低频不稳定燃烧研究

介绍了85％H2O2-PE固液火箭发动机的低频不稳定燃烧特征;应用发动机质量守恒方程对发动机低频耦合振荡燃烧现象进行了一维模拟,分析了氧化剂喷射压降对低频不稳定燃烧的影响。利用扰动分析确立了固液火箭发动机的稳定工作限。提出了抑制低频耦合振荡燃烧的方法。     

超静超稳卫星碰振动力学建模

针对分离式卫星载荷模块(PM)受到扰动时可能与服务模块(SM)发生碰撞的问题，综合音圈电机反电动势(back-EMF)和柔性线缆动力学的效应，基于牛顿欧拉法建立了分离式卫星(DFP)载荷模块动力学模型。基于Hertz接触理论，推导了分离式卫星碰撞过程中连续接触力模型，并分析了碰撞过程中产生的接触力对载荷模块指向精度和指向稳定度的影响。数值仿真结果表明，碰撞使得载荷模块指向精度和指向稳定度下降5个数量级，碰撞后载荷模块可再次恢复到超静超稳工作状态，恢复时间超过1400 s。本文建立的碰撞模型对研究分离式卫星碰撞规避和碰撞控制具有重要意义。     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.     

Numerical Analysis of Dry Friction-Induced Vibration of Moving Slider-Elastic Annular Beam System

A disc-pad friction system is modelled as that two moving pads act symmetrically on an annular beam with flexible boundary condition.Simulation procedure is proposed to deal with the moving interactions and calculation is carried out by using the finite difference method,which shows that only the first-order mode vibration of the beam can be induced.Then the partial differential equation of motion of the disk is reduced to a first-order mode vibration system with time-varying stiffness.As the disk speed is decreased below the critical speeds,the relative equilibrium of the pad on the disk loses its stability and stick-slip type limit cycle vibrations are resulted in all directions′movements.Acceleration of the disk motion on the frictional instability is also investigated.The period of stick-slip vibration with large amplitude will be shortened with higher moving deceleration.     

基于动态补偿的多电机控制算法

多电机协调控制达到转速一致是电机控制中的一个关键难题，外加负载变动和电机参数变化时会引起电机性能的下降，达不到良好的控制效果。为使电机间保持转速同步，建立了永磁同步电机d-q坐标系下的矢量控制数学模型，基于转速跟随控制，提出一种基于单神经元PID的变增益速度补偿器进行偏差耦合控制。在MATLAB/Simulink建立了3台永磁同步电机的仿真模型。仿真结果表明，与传统PID固定增益速度补偿器算法相比，单神经元PID的变增益速度补偿器具有更强的鲁棒性以及更快的收敛性。     

热等静压对激光选区熔化成形GH4169合金持久性能的影响

采用激光选区熔化(SLM)成形技术制备了GH4169合金,运用金相显微镜(OM)、扫描电子显微镜(SEM)、电子背散射衍射(EBSD)和透射电镜(TEM)等分析手段分析了热等静压对SLM成形GH4169合金组织及持久性能的影响规律。结果表明:沉积态合金组织中,沿沉积方向的晶粒为柱状晶,晶粒内枝晶组织细小,枝晶间分布大量Laves相;热等静压处理可有效消除组织中气孔缺陷,溶解大部分Laves相,促使组织晶粒等轴化,并减少后续980℃固溶处理过程中δ相在晶内的析出;热等静压处理能提高合金的持久寿命,但会降低合金的持久塑性。     

重型燃气轮机高雷诺数CDA叶型转捩特性数值计算

为研究重型燃气轮机的压气机叶片在高雷诺数工况下的气动性能,基于Gamma-Theta转捩模型的雷诺时均方程对某可 控扩散叶型进行了数值计算。通过对比不控制马赫数与控制马赫数,分析高雷诺数对可控扩散叶型气动性能及转捩特性的影响。 结果表明：在不控制马赫数条件下,在零攻角时,雷诺数从7×10 5 增大为9×10 5 ,总压损失增加了约391.95%;在高雷诺数工况下随 着雷诺数的增大,叶片流动损失不断增大,叶片可用攻角范围减小,同时在叶片吸力面出现激波,干扰转捩的产生。在控制马赫数 条件下,当Ma=0.6时,在零攻角工况下,雷诺数从8.2×10 5 增大为1×10 7 ,总压损失减小了约38.98%,吸力面转捩起始点从4.78%弦 长处前移至1.11%弦长处;在高雷诺数工况下,叶片流动损失随着雷诺数的增大不断减小,吸力面转捩位置前移。     

超临界RP-3航空煤油喷嘴内部流动与相变特性研究

未来航空燃气轮机采用燃油作为冷却剂,对发动机冷却空气及热端部件进行冷却,使得燃油在进入燃烧室之前超过其热力学临界点,燃油的热力学性质发生巨大变化,将对燃油在喷嘴内的流动和喷嘴下游的喷射掺混过程产生重要的影响,因此有必要对超临界RP-3在喷嘴内的流动与相变特性展开研究。本文采用自主设计的喷嘴内部收缩通道模拟试验件,对超临界RP-3在喷嘴内的沿程压力分布进行测量,并采用基于一维等熵假设的计算方法进行数值模拟。试验首次获得了超临界航空煤油RP-3在喷嘴收缩通道内的沿程静压分布随喷射压力、温度变化的规律。通过与模型对比,发现未发生相变时,计算结果与试验值拟合精度较高,可以较好地预测RP-3在喷嘴内的流动参数,喷嘴内的静压分布也趋于一致;发生冷凝相变时,计算结果与试验值产生误差较大,喷射参数对于静压分布存在着较大的影响。本文试验获得的超临界RP-3航空煤油在喷嘴内的流动与相变特性,为航空发动机超临界RP-3喷射的喷嘴设计提供了重要的设计依据。