Self-Tuning Excitation Control for Synchronous Machine

A novel scheme for the control of synchronous generator excitation system is described. The proposed controller, which makes use of self-tuning proportional-integral (PI) control, is very effective for improving the dynamic performance of the synchronous machine over a wide range of operating conditions when the machine is subjected to major disturbances or small random load changes. A fixed-gain PI excitation controller is also included for comparison.     

Streamer Evaporation

Streamer evaporation is the consequence of heating in ideal MHD models because plasma is weakly contained by the magnetic field. Heating causes inflation, opening of field lines, and release of solar wind. It was discovered in simulations and, due to the absence of loss mechanisms, the ultimate end point is the complete evaporation of the streamer. Of course streamers do not behave in this way because of losses by thermal conduction and radiation. Heating is also expected to depend on ambient conditions. We use a global MHD model with thermal conduction to examine the effect of changing the heating scale height. We also extend an analytic model of streamers developed by Pneuman (1968) to show that steady streamers are unable to contain plasma for temperatures near the cusp greater than ∼ 2 × 10⁶ K. This revised version was published online in June 2006 with corrections to the Cover Date.     

Time delay estimation with multiple looks in colored Gaussian noise

We present an efficient algorithm for high resolution time delay estimation in colored Gaussian noise with multiple looks. By using a relaxation-based optimization approach and exploiting the Toeplitz property of the noise covariance matrix, the enhanced new algorithm can achieve the corresponding Cramer-Rao bounds (CRBs) with a very small number of independent looks     

FATIGUE CRACK CLOSURE MEASUREMENT OF 2024-T3 SHEET SPECIMEN

ＦＡＴＩＧＵＥＣＲＡＣＫＣＬＯＳＵＲＥＭＥＡＳＵＲＥＭＥＮＴＯＦ２０２４－Ｔ３ＳＨＥＥＴＳＰＥＣＩＭＥＮＷｕＹｉｓｈｅｎｇ（ＩｎｓｔｉｌｕｔｅｏｆＭｅｃｈａｎｉｃｓ，ＣｈｉｎｅｓｅＡｃａｄｅｍｙｏｆＳｃｉｅｎｃｅｓ，Ｂｅｉｊｉｎｇ，Ｃｈｉｎａ，１００...     

航空结构钢激光辐照提高疲劳强度的研究

对激光辐照的温度场进行了分析与计算。以此为依据,针对典型的航空结构钢３０ＣｒＭｎＳｉＡ和３０ＣｒＭｎＳｉＮｉ２Ａ的典型试件,采用了优化的参数和方式进行激光辐照,并进行了疲劳试验。结果表明：两种材料的疲劳寿命均有明显提高。从而证明,激光辐照强化是。一项提高航空结构钢疲劳性能的有效表面强化工艺。     

杯杯型复合挤压两种宏观缺陷并存分析

 通过杯杯型轴对称复合挤压两种宏观缺陷并存的上限分析表达式,研究了该变形方式下两种宏观缺陷并存区域与正挤部分、反挤部分变形程度和坯料相对余厚的关系。本文的模型及结论被实验结果所证实。     

航空嵌入式系统2000年问题分析及检测方法

通过对航空系统嵌入式计算机的应用分析,根据航空系统嵌入式计算机应用领域和重要性的不同,将航空系统分为机载电子系统,遥测与导航系统,设备开发、测试和综合系统,以及生产加工系统四个层次。并针对每个层次绝对时间的使用特征,从系统参数共享到底层电路构型,提出了各自相应的 Ｙ２ Ｋ 问题检查方法,以及相应的检查内容和责任单位。     

烟丝配料单片机控制系统

本文介绍了配料生产过程中单片机控制系统的硬件结构及软件流程。由于硬件和软件设计上都采用了模块化的结构,所以便于安装调试,整个系统可推广到诸如水泥、矿产、食品加工等生产中。     

关于模糊逻辑系统及其建模函数的数学描述

模糊逻辑系统按真值化处理与推量规则导出最优系统数学表达式。在线性定常状态下,分别建立起连续与间断系统的数学模型,归纳出模糊控制的等效解法。并应用模糊数学算法,对一非线性实例绘制出双模控制框图。     

一种定向凝固高温合金低周疲劳性能的研究

研究了同成分合金在定向凝固（ＤＳ）和普通铸造（ＣＣ）状态下７６０℃的低周疲劳性能。结果表明，ＤＳ合金的疲劳寿命比ＣＣ合金在应力控制条件下高２倍左右，而在应变控制条件下可提高寿命２０倍左右。ＣＣ合金的疲劳裂纹往往萌生在与表面相连的晶界或某些缺陷（如孔洞）上，由外向内沿晶界扩展。而ＤＳ合金裂纹则起源于纵向晶界的横段或预开裂的碳化物，并沿枝晶间穿枝干扩展。