Multiposition alignment of strapdown inertial navigation system

The authors demonstrate that the stationary alignment of strapdown inertial navigation system (SDINS) can be improved by employing the multiposition/technique. Using an observability analysis, it is shown that an optimal two-position alignment not only satisfies complete observability conditions but also minimizes alignment errors. This is done by analytic rank testing of the stripped observability matrix and numerical calculation of the error covariance. It is also shown that an optimal three-position alignment accelerates the convergence of the alignment error compared with two-position alignment     

FUZZY PETRI NET FOR FAULT DIAGNOSIS

ＦＵＺＺＹＰＥＴＲＩＮＥＴＦＯＲＦＡＵＬＴＤＩＡＧＮＯＳＩＳＷｕｙａｎｆａｎｇ；ＷｅｉＺｈｏｎｇｘｉｎ．（ＤｅｐａｒｔｍｅｎｔｏｆＭｅｃｈａｎｉｃａｌＥｎｇｉｎｅｅｒｉｎｇ，ＮａｎｊｉｎｇＵｎｉｖｅｒｓｉｔｙｏｆＡｅｒｏｎａｕｔｉｃｓａｎｄＡｓｔｒｏ...     

Improved Switching Converter Model Using Discrete and Averaging Techniques

The nonlinear modeling and analysis of dc-dc converters has been done by averaging and discrete-sampling techniques. The averaging technique is simple, but inaccurate, as the modulation frequencies approach the theoretical limit of one-half the switching frequency. The discrete technique is accurate even at high frequencies, but is very complex and cumbersome. An improved model is developed by combining the aforementioned techniques. This new model is easy to implement in circuit and state variable forms and is accurate to the theoretical limit.     

Nondestructive Characterization of RBSOA of High-Power Bipolar Transistors

Reverse-bias safe operating area (RBSOA) of high-power Darlington transistors is characterized using a 120 A/1000 V nondestructive reverse-bias second breakdown tester designed and fabricated at Virginia Polytechnic Institute and State University. Elaborate RBSOA characteristics are generated with different forward/reverse base drives and collector current levels. The effects of elevated case temperature and second-base drive on RBSOA of four-terminal Darlington devices are also discussed.     

喷雾运动初始条件问题的研究

根据所完成的流动环境中颗粒在初始区域内速度分布的测量结果，对颗粒运动初始条件的问题进行了全面的研究，提出了统计性，随机性和确定性的三种初始条件及其数学处理方法，在此基础上，应用喷雾两相流的数值方法，计算了喷雾的运动，比较了不同初始条件对计算结果的影响，并将所得计算结果与实验结果做了比较，两者符合较好。     

突扩后突缩的三维流场计算

根据有关固体火箭发动机装药后端到喷管间的空间特征,对三维突扩后突缩内部流场计算进行了探索和研究。计算中成功地应用了SIMPLE算法解决复杂的三维流场计算问题,并在初场构成、源项离散及松弛系数的选取等方面都进行了调试改进。通过建立计算模型、划分网格、对方程及边界条件离散化和非线性处理,以及线性方程组求解等,计算得到了符合物理规律的数值解,指出了空间涡及二次涡的存在。     

漩涡发生器对燃油喷嘴的雾化性能影响的数值研究

为了探讨漩涡发生器(简称V.G)对燃油喷嘴雾化性能的影响,利用Gambit分别建立了原型喷嘴、加装2个漩涡发生器和加装4个漩涡发生器喷嘴的模型,并利用FLUENT软件进行了数值模拟,得到了三种模型的出口流场分布图。计算结果表明:在相同燃油压力下,加装漩涡发生器可以加快射流的混合速度,其中加装4个漩涡发生器的喷嘴的加速掺混能力最高,加装2个的其次,但仍比"原型"的情况有明显的改善;当燃油压力改变时,掺混能力会随着燃油压力的提高而提高。     

离心叶轮出口与无叶扩压器内部流动特性的DPIV实验研究

在叶轮转速n＝1500rpm对应的设计工况下,利用两维数字式粒子图像速度场仪(DPIV)对风机模型从叶轮出口至无叶扩压器区域内部流动状态进行整场测量,在"锁相"状态下获得沿扩压器宽度方向上三个径向面的瞬态速度场、涡量场的分布,并进一步对时均流场的流动特性进行全面讨论.测量结果表明:设计工况下,叶轮出口流动呈现典型的"射流-尾迹"流动结构,其对无叶扩压器内部流动状态具有深刻的影响.旋涡由叶轮叶片表面边界层的粘性切应力产生,并随流动被输运至下游无叶扩压器,然后随着流动的均匀化而逐渐消失.涡量的分布及变化反映了无叶扩压器内部流体相互掺混和能量传递、重新分布从而达到均匀化的过程.随着半径的增加,尽管无叶扩压器内流动在圆周方向亦逐渐趋于均匀化,但沿宽度方向的差距未得到改善,这将导致沿轴向α不变原则设计的叶片扩压器的二元叶片无法避免冲击损失.     

DO 28飞行试验数据一致性检验

 本文研究DO28试验机飞行试验数据一致性检验及其误差校正。建立了由非线性运动学方程及内容广泛的校正环节构成的一致性检验模型,解决了大地风场重构、测量信号时间延迟估计、ψ转换及测量控制信号的校正。为DO28参数估计提供了可靠、准确的飞行试验数据。     

Comparison of half-bridge off-line, ZCS-QRC and ZVS-MRC

The performance of the half-bridge (HB) zero-current-switched (ZCS) quasi-resonant converter (QRC) and zero-voltage-switched (ZVS) multiresonant converter (MRC) is compared with respect to their efficiency, input voltage range, semiconductor stresses, power density, and reliability. The efficiency of the HB ZVS-MRC at a given nominal input is shown to be highly dependent on the range of the input voltage, and it suffers when the converter has to be designed to cover a wide range. However, this is not the case for the HB ZCS-QRC. Experimental versions of the HB ZCS-QRC and HB ZVS-MRC were designed for the input voltage range from 150 to 350 V and a maximum output power of 100 W, under the same constraints, to facilitate their comparison