滤波减速器有限长轮齿接触表面混合润滑分析

综合考虑了轮齿接触几何、啮合点法向载荷、齿向参数、真实表面粗糙度、润滑剂流变特性等因素,建立了滤波减速器轮齿混合润滑数值分析模型,采用复合迭代法和快速傅里叶变换(FFT)方法分别求解Reynolds方程和弹性变形方程,获得了轮齿接触表面混合润滑分析完全数值解,得到了滤波减速器在啮入点、节点和啮出点的压力与平均油膜厚度,以及转速对轮齿接触表面平均油膜厚度和接触比的影响.结果表明:在啮入点、啮出点及节点处,沿齿宽方向的压力分布不相等,两侧压力较大,而在啮入点处的两侧压力突变相对较小,且平均油膜厚度最大;对于粗糙轮齿接触表面,随着滤波减速器转速逐渐降低,啮入点、节点及啮出点的平均油膜厚度随之减小,接触比增加,润滑效果变差,并且在同一工况下粗糙轮齿接触表面的啮合点平均油膜厚度小于光滑轮齿表面的平均油膜厚度.      

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

基于技术参数评估的涡扇发动机总体性能设计分析

为了充分掌握各代涡扇发动机技术参数水平及其发展趋势,统计包括现役型号在内的15台2～4代涡扇发动机的总体性能参数、循环参数和部件参数,采用考虑涡轮冷却的总体性能计算和重量预测相结合的发动机技术参数综合评估模型并利用计算程序绘制趋势曲线,评估技术参数的发展趋势,结果表明技术参数逐年改善的趋势是比较稳定的,并用曲线趋势外推法取得下一代关键参数的定量数据。在此基础上探索下一代高推重比涡扇发动机可能的总体性能方案,为下一代先进涡扇发动机的预研和设计提供参考。     

无控武器对地攻击精度分析

针对目前无控武器对地攻击精度影响因素来源单一,分析影响精度的多种误差源。建立直升机无控武器命中精度分析模型,针对平飞方式下的无控武器命中精度问题,采用蒙特卡洛法多次仿真。针对命中精度与各个误差源的关系方程,提出采用多元线性回归法对仿真结果进行分析,给出误差源对命中精度的影响程度。对关系方程和误差影响程度进行显著性检验,使其更加准确、可信。     

7085铝合金残余应力及加工变形的数值仿真与试验

毛坯残余应力的测量以及零件的加工变形分析是航空整体结构件数控加工工艺研究的难题。应用MSC.Marc软件对某型飞机主起支撑接头的7085铝合金锻件毛坯的淬火-压缩工艺进行了数值仿真,获得了毛坯残余应力分布趋势;应用X射线衍射法与钻孔法测量了毛坯表层残余应力分布,提出了基于系数修正法的毛坯残余应力分析方法,通过最小二乘法（LSM）拟合仿真值与试验值以获得应力修正系数,并对毛坯残余应力分布的仿真结果进行修正,获得了实际毛坯的残余应力分布;由此进行了主起支撑接头缩比零件加工变形仿真与验证试验。研究结果表明：7085铝合金块状毛坯残余应力数值仿真结果与测试结果的趋势吻合,为应力修正提供了物理基础;相对于未修正的应力分布,基于修正后的应力分布仿真获得的变形结果精度提高了50%;7085-T7452铝合金的毛坯残余应力是导致主起支撑接头加工变形的主要因素。     

Adaptive Gaussian sum squared-root cubature Kalman filter with split-merge scheme for state estimation

The paper deals with state estimation problem of nonlinear non-Gaussian discrete dynamic systems for improvement of accuracy and consistency. An efficient new algorithm called the adaptive Gaussian-sum square-root cubature Kalman filter（AGSSCKF） with a split-merge scheme is proposed. It is developed based on the squared-root extension of newly introduced cubature Kalman filter（SCKF） and is built within a Gaussian-sum framework. Based on the condition that the probability density functions of process noises and initial state are denoted by a Gaussian sum using optimization method, a bank of SCKF are used as the sub-filters to estimate state of system with the corresponding weights respectively, which is adaptively updated. The new algorithm consists of an adaptive splitting and merging procedure according to a proposed split-decision model based on the nonlinearity degree of measurement. The results of two simulation scenarios（one-dimensional state estimation and bearings-only tracking） show that the proposed filter demonstrates comparable performance to the particle filter with significantly reduced computational cost.     

载人登月人货分运与人货合运模式对比分析

由于载人航天任务所具有的确保航天员安全的特殊属性,载人登月任务模式往往因此必须考虑救生等多种环节和因素,变得十分复杂。针对目前载人登月人货分运及人货合运两种任务模式,通过比较分析表明,从安全性、任务风险、飞船设计约束、发射窗口、测控支持复杂度方面来看,人货合运模式要优于人货分运模式,但是人货合运模式中的重型火箭如果被要求按照载人火箭标准进行设计和考核,其研制周期、经费方面的投入将会增加。     

一种基于历史标校数据的移相值预测方法

地面测控设备在执行测控任务前,需要对和差接收通道的相位差进行标校(简称校相),以满足测角分系统的目标自跟踪要求.针对因标校设备故障而无法进行校相的问题,通过使用数理统计的多元回归分析方法,对积累的历史标校数据进行分析,确定了设备工作的环境温度对跟踪接收机移相值有显著影响.在此基础上,利用滑动窗口多项式拟合方法得到拟合移相值,并与最近一次的标校移相值进行时变加权,可以得到基于历史标校数据的移相值预测方法.仿真试验表明该方法具有较好的预测精度,可将预测移相值作为跟踪接收机参数,提高测控设备应急测控能力.     

基于确定学习理论的轴流压气机系统分岔预测

针对轴流压气机系统中的分岔预测问题,基于简化的Moore-Greitzer 3阶压气机模型,分析了该系统中存在的分岔现象;利用最新发展的确定学习理论,对压气机系统随着γ参数变化出现的几种典型模态的相关系统动态进行辨识,并将所学知识保存成常值RBF神经网络以构成模式库;利用该模式库构建1组嵌入了常值RBF神经网络的动态估计器;将测试模式与估计器相比,得到1组残差,并利用动态模式识别方法的残差最小原则实现了对Pitchfork分岔的预测。