结构隔绝内-外空间的流-热-固耦合仿真应用

为验证和指导高速飞行器的防隔热设计,准确地模拟气动热产生的热量穿透防隔热材料进而影响舱内温度空间分布和时间变化的过程,研究了一种同时求解机体外流场及气动热、机体结构传热及舱内流场温度场仿真计算方法,其中的传热方式包括热传导、热对流及热辐射。采用两套计算模型、两种求解器、一个数据交换文件的计算结构,构建了一种针对流场-热-结构的多场耦合分析方法,实现了对固体隔绝内外流场温度动态变化问题的仿真分析。最后通过计算实例验证了整套计算方法,得到的飞行器舱内温度变化特性能够用于指导高速飞行器的防隔热设计。     

绕圆头回转体通气空化流型的实验研究

为了深入了解通气空化流动现象,利用高速全流场显示技术,对绕圆头回转体通气空化流型进行实验研究。结果表明,重力效应和通气量对通气空化的多相流流型起主要作用。定义了弗洛德数和通气率两个无量纲数,将绕圆头回转体通气空化分为5种多相流流型,即透明空泡、透明气弹、透明分层、水气混合以及半透明水气混合。流动参数对流型的影响分为2个阶段,即重力起主要作用阶段和重力效应不明显阶段。在重力起主要作用阶段,通气率一定时,随着弗洛德数的增大,附着弹体的空泡倾斜程度变小,弹体上表面的断裂空泡转变为贴着弹体壁面的稳定空泡;弗洛德数一定时,随着通气率的增大弹体上表面断裂空泡的尺度不断增大。在重力效应不明显阶段,通气率一定时,随着弗洛德数的增大,雷诺数变大,流场的湍流强度增大,空泡尾流区域水气交换的程度加剧;弗洛德数一定时,随着通气率的增大,通气空化数减小,绕弹体的云雾状空泡逐渐转变为透明空泡。最后,进一步分析了重力影响下透明空泡脱落的非定常过程,以及反向射流作用下云雾状空泡交替脱落的非定常过程。     

民用航空发动机航线维修专家系统设计分析

为了缩短民用航空发动机航线维修的时间,提高航线维修效率,降低航班延误率,针对民用航空发动机航线维修工作的特点,提出了基于故障特征利用模糊技术建立专家系统的模糊知识库,并结合智能检索技术建立民用航空发动机航线维修专家系统的方法,该方法能够提高专家系统解决问题的准确性和时效性。重点阐述了专家系统模糊知识库构建和智能检索技术的逻辑思路。相比于以关键故障特征为知识点建立的数据库,模糊知识库包含了更全面的故障特征知识。智能检索基于概念或语义检索,相比于关键词检索,对自然语言有更好地理解,便于航线维修工作人员使用。     

高焓激波风洞喷管流场非平衡特性研究

高焓激波风洞是开展高超声速流动研究的重要地面模拟设备,但其产生的高焓气流在喷管中的膨胀过程是一种典型的热化学非平衡流动,试验段特征参数通过直接实验测量难以完全确定。本文通过求解耦合双温度模型的轴对称Navier-Stokes方程,研究了高焓激波风洞中典型状态下气流的热化学非平衡流动特性,分析了焓值对非平衡特性的影响规律。结果表明,喷管出口自由流均匀区域达到出口截面直径的75%以上,能够为实验提供足够的空间;喷管出口自由流处于热化学非平衡状态,在喷管喉道后约1/5喷管长度处气流即已处于冻结流状态,组分浓度和振动温度随气流流动基本不变;焓值在8.4MJ/kg~19.5MJ/kg之间变化时,非平衡程度随着焓值的增加而增强,但是低焓值时非平衡程度的增强更加剧烈。     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。     

机翼顶起设计解析

飞机全机顶起是飞机维护时必不可少的操作程序,其中机翼顶起是全机顶起的一个重要组成部分。机翼顶起设计包括两个方面内容,即顶垫设计和机翼千斤顶选型。顶垫设计与顶起点结构设计、机翼千斤顶选型是联合设计、相互影响的。     

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

Adaptive Gaussian sum squared-root cubature Kalman filter with split-merge scheme for state estimation

The paper deals with state estimation problem of nonlinear non-Gaussian discrete dynamic systems for improvement of accuracy and consistency. An efficient new algorithm called the adaptive Gaussian-sum square-root cubature Kalman filter（AGSSCKF） with a split-merge scheme is proposed. It is developed based on the squared-root extension of newly introduced cubature Kalman filter（SCKF） and is built within a Gaussian-sum framework. Based on the condition that the probability density functions of process noises and initial state are denoted by a Gaussian sum using optimization method, a bank of SCKF are used as the sub-filters to estimate state of system with the corresponding weights respectively, which is adaptively updated. The new algorithm consists of an adaptive splitting and merging procedure according to a proposed split-decision model based on the nonlinearity degree of measurement. The results of two simulation scenarios（one-dimensional state estimation and bearings-only tracking） show that the proposed filter demonstrates comparable performance to the particle filter with significantly reduced computational cost.