HB-3000型布氏硬度计换向系统的改造

介绍了ＨＢ－３０００型布氏硬度计换向系统的改造方法及改造后硬度计的工作程序,并就改进效果进行了论述。     

光栅式长度仪表示值误差检定系统

介绍了光栅式长度仪表示值误差检定系统的基本工作原理以及关键技术的解决。本系统具有测量精度高、重复性好、智能化、操作简单、用户可自由扩展等优点。     

基于3RRS-Bricard复合空间捕获系统运动学分析

面向跨尺度、目标多样化的空间捕获任务,融合Bricard和3RRS机构的折展特性和几何特点对复合捕获系统运动学进行了分析。基于捕获系统的自由度和构型特点分析,通过构建Bricard与3RRS间的转换关系实现了捕获系统各机构间的运动学解耦。根据六棱柱模型,引入Bricard虚拟顶点,设计了面向复合空间捕获系统的运动学求解方法。在仿真环境下搭建捕获系统的运动学和动力学模型,并开展针对动态捕获目标的轨迹跟随实验。通过与基于闭环约束的阻尼最小二乘法（DLS）对比,验证了该运动学求解算法的有效性和先进性。实验结果表明,捕获系统可实现平稳的协同控制,运动过程中位置跟随精度优于4 mm,姿态精度优于0.035 rad。     

典型智能材料结构疲劳可靠性问题研究进展

智能材料结构在众多领域应用广泛,为防止智能材料结构在使用时发生疲劳失效,研究智能材料结构的疲劳可靠性问题有着重要意义.本文从疲劳失效的微观表征、疲劳试验的宏观现象以及疲劳可靠性问题的研究方法等角度,分析了裂纹对压电传感器性能的影响,探究了压电换能器在振动能量回收中发生疲劳失效的机理.阐述了形状记忆合金发生结构性疲劳的微...     

Aerodynamic Design and Analysis of a Low-reaction Axial Compressor Stage

There is introduced a new low-reaction, highly-loaded axial compressor design concept which is coupled with boundary layer suction method. The characteristic features of the concept are made clear through its comparison with the MIT boundary layer suction compressor. Also are pointed out the potential applications of this concept as well as its key technological problems. Based on this concept, a single-stage, low-reaction and low-speed axial compressor is constructed in association with analysis and computation of boundary layer suction on vanes with the aid of a three-dimensional numerical approach. The results attest to the effectiveness of this way to control separation in blade cascades by the boundary layer suction and the feasibility of this proposed design concept.     

Nonlinear Dynamics Behaviors of a Rotor Roller Bearing System with Radial Clearances and Waviness Considered

A rotor system supported by roller beatings displays very complicated nonlinear behaviors due to nonlinear Hertzian contact forces, radial clearances and bearing waviness. This paper presents nonlinear bearing forces of a roller bearing under four-dimensional loads and establishes 4-DOF dynamics equations of a rotor roller bearing system. The methods of Newmark-β and of Newton-Laphson are used to solve the nonlinear equations. The dynamics behaviors of a rigid rotor system are studied through the bifurcation, the Poincar è maps, the spectrum diagrams and the axis orbit of responses of the system. The results show that the system is liable to undergo instability caused by the quasi-periodic bifurcation, the periodic-doubling bifurcation and chaos routes as the rotational speed increases. Clearances, outer race waviness, inner race waviness, roller waviness, damping, radial forces and unbalanced forces-all these bring a significant influence to bear on the system stability. As the clearance increases, the dynamics behaviors become complicated with the number and the scale of instable regions becoming larger. The vibration frequencies induced by the roller bearing waviness and the orders of the waviness might cause severe vibrations. The system is able to eliminate non-periodic vibration by reasonable choice and optimization of the parameters.     

金属橡胶减振器用于发动机安装减振的研究

 为减小发动机传递至飞机机身结构的振动,设计了金属橡胶减振器用于航空发动机安装。对该金属橡胶减振器进行了动力学建模研究,采用有限元技术对安装减振器前后的飞机全机结构进行了仿真分析,初步表明了该设计对结构频率影响较小,但能引入较大阻尼,降低响应水平。在理论分析基础上,进一步将设计制造的金属橡胶减振器安装于某型飞机,进行地面开车,实测了应用减振安装前后飞机的动力学响应。结果证明了发动机减振安装的可行性与有效性。     

基于预测脱靶量的远程拦截速度增益导引

 针对拦截器使用耗尽关机固体燃料发动机的情况,设计了大气层外目标拦截的速度增益导引方法。导引律中根据Lambert导引确定指令推力方向初值,利用剩余速度增量信息,计算惯性速度增益下的预测脱靶量,使用Kepler轨道摄动方程计算消除脱靶量所需的速度增益修正,根据惯性速度增益和速度增益修正之和确定指令推力方向。给出了一种计及J2项引力摄动影响的滑行段弹道预测半解析方法,减少导引律运算量,降低导引方法误差;导引律中引入了剩余速度增量测量环节,增强了导引精度对推进系统参数的鲁棒性。与传统的通用能量管理（GEM）导引相比,采用该导引律拦截远程目标时指令推力方向平稳、变化范围小,脱靶量降低了两个数量级。     

纤维单向缠绕制备C/C扩张段成型技术

在"锥形体纤维单向缠绕技术"的基础上进行了碳纤维单向缠绕制备C/C扩张段成型工艺的探索,制备出了Φ180 mm C/C扩张段试验件,并对其进行了性能测试及整体探伤.测试结果为:超声探伤分贝差为15 dB的缺陷面积小于5%;沿母线方向层间剪切强度大于10 MPa,大端环向层间剪切强度偏小;内压爆破压强为0.6 MPa,破裂模式较好.试验结果表明,采用碳纤维单向缠绕技术制备C/C扩张段工艺可行.     

旋转对固体火箭发动机燃烧室燃气流动的影响

采用RNG k-ε湍流模型,计算了某管状装药旋转固体火箭发动机在不同旋转速度情况下的燃烧室喷管统一流场,着重分析了不同转速情况下燃烧室内燃气流动的特点,得到了该发动机燃烧室内旋流切向速度沿径向分布趋势以及旋流涡核半径在不同转速情况下的变化特点,对燃烧室前封头局部区域的流场结构也进行了较为细致的分析.