TDICCD时序设计在FPGA中的工程实现

文章结合TDICCD和FPGA器件特点，主要从设计目标分析，VHDL算法描述、综合、布线、仿真、代码优化、代码测试验证等几方面，阐述了TDICCD时序设计的全过程；利用同步设计的思想避免了竞争与冒险；利用RC延迟模块实现了时序的精确调整；利用模块化思想提高了代码的可重用性、可测试性、可读性。最终，实现了一个6MHz像元输出速率下能正常工作的TDICCD的成像系统。     

慧眼观火星

“火星侦察轨道器”（MRO）是2005年8月12日在美国卡纳维拉尔角航天发射场由“宇宙神”5火箭发射的，目前已于3月10日成功完成精细的入轨机动动作，进入绕火星运行的轨道，离表面最近点的高度约420千米。它是当今世界最大，设备最精良，最先进的火星探测器。[编者按]     

HSDB网络稳定性的研究

高速数据总线（ＨｉｇｈＳｐｅｅｄＤａｔａＢｕｓ，ＨＳＤＢ）是新一代航空电子系统的数据总路线，ＨＳＤＢ网络实际上是基于线性令牌总线的一个专用计算机局域网，在网络上负载较重且时间非苛刻的消息到达是一般过程的条件十分别讨论了网络的局域和全域稳定性，并导出了保证整个网络稳定的令牌握有定时器最小值，同时给出了如何根据应用去调整得到的理论值。     

TVC/PSM飞机的过失速动态边界及敏捷性分析

以飞机为质点，考虑在最少输入数据情况下，曲于转弯速率图并从能量的角度计算和分析了TVC/PSM飞机的过失速动态边界，选取敏捷性尺度空战周期时间和指向裕度，对比分析了TVC/PSM飞机和传统飞机的敏捷性，得出了一些有益的结论，并提出了一些建议。     

氢涡轮泵转子不稳定因素分析

通过实例说明，液氢低温下钢和铝材料收缩量不同所引起的转子松动可能是氢涡轮泵次同步进动的主要原因。     

铝合金T型材拉弯成形的有限元模拟

针对目前拉弯成形中的问题,采用有限元模拟的方法,对带下陷拉弯过程进行计算机仿真,得到优化后的工艺参数,避免了盲目的试拉,提高了加工效率,降低了拉弯成本,积累了带下陷拉弯成形的经验,提高了公司拉弯工艺水平。     

一般高速数据总线网络的吞吐量分析

分析了一般高速数据总线网络优先权方案的特性，建立了一般ＨＳＤＢ网络多优先权的平均吞吐量模型，导出了不同优先权的平均吞吐量解析表达式，并通过软件仿真验证了由得到的解析表达式。     

箭体上的凸起物对火箭气动特性的影响

综合大量实验研究结果,本文给出了火箭箭体上的环形凸起物和纵向凸起物对火箭气动特性的影响。其中最主要的是改变滚转力矩的大小和方向。而这正是姿态控制系统设计的重要依据之一。因此,给出凸起物的设计原则,对火箭气动设计有实际意义。     

A method of estimating GPS instrumental biases with a convolution algorithm

This paper presents a method of deriving the instrumental differential code biases (DCBs) of GPS satellites and dual frequency receivers. Considering that the total electron content (TEC) varies smoothly over a small area, one ionospheric pierce point (IPP) and four more nearby IPPs were selected to build an equation with a convolution algorithm. In addition, unknown DCB parameters were arranged into a set of equations with GPS observations in a day unit by assuming that DCBs do not vary within a day. Then, the DCBs of satellites and receivers were determined by solving the equation set with the least-squares fitting technique. The performance of this method is examined by applying it to 361?days in 2014 using the observation data from 1311 GPS Earth Observation Network (GEONET) receivers. The result was crosswise-compared with the DCB estimated by the mesh method and the IONEX products from the Center for Orbit Determination in Europe (CODE). The DCB values derived by this method agree with those of the mesh method and the CODE products, with biases of 0.091?ns and 0.321?ns, respectively. The convolution method's accuracy and stability were quite good and showed improvements over the mesh method.     

Predicting performance in manually controlled rendezvous and docking through spatial abilities

Manually controlled rendezvous and docking (manual RVD) is a challenging space task for astronauts. This study aims to identify spatial abilities that are critical for accomplishing manual RVD. Based on task analysis, spatial abilities were deduced to be critical for accomplishing manual RVD. 15 Male participants performed manual RVD task simulations and spatial ability tests (the object-manipulation spatial ability and spatial orientation ability). Participants’ performance in the test of visualization of viewpoints (which measures the spatial orientation ability) was found to be significantly correlated with their manual RVD performance, indicating that the spatial orientation ability in the sense of perspective taking is particularly important for accomplishing manual RVD.