Equivalent model of close-packed film cooling holes in nickel-based single crystal cooled blade based on crystallographic theory

The mechanical properties of nickel-based single crystal thin-walled plate with close-packed film cooling holes were studied based on the equivalent solid material concept. The effective plastic parameters inversion method based on crystallographic theory were proposed. A simplification method for close-packed film cooling hole plates with square and triangular penetration patterns was presented. A large number of finite element analysis results covering different ligament efficiencies and penetration patterns were provided to verify the feasibility of the plastic equivalent principle and simplification method. The results show that the stress–strain curve and resolved shear stresses of simplification models are in consistence with the plate models with close-packed film cooling holes. The equivalent errors of yield strength are all within the error band and the values of equivalent errors are all less than 10%. In addition, the equivalent errors of the positions where maximum resolved shear stress occurs are all less than 15°, indicating the accuracy of plastic equivalent model and simplification method.     

CO2用于气动弹射的可行性分析

针对传统气动弹射介质空气做功能力不足的问题,提出采用CO_2作为新型气动弹射介质。基于质量守恒和能量守恒定律建立了以CO_2为弹射介质的弹射热力模型,并使用该模型对比分析了CO_2和空气作为弹射介质对于弹射性能的影响。得到了弹射过程中高低压室内介质状态以及飞行器运动参数的动态变化过程。与空气相比,CO_2具有更大的做功能力。相同的热力状态下弹射相同质量的飞行器,使用CO_2可获得更大的出筒速度。CO_2作为弹射工质对于大质量的飞行器优势明显,在不减小出筒速度的情况下,使用CO_2可使负载质量提升50%以上,验证了CO_2作为弹射工质的可行性。     

Hypersonic vehicle aerodynamic design using modified sequential approximate optimization

Hypersonic vehicles are receiving increased attention within the aerospace community due to their high cruise speed and long-range capabilities. In this paper, a modified Sequential Approximate Optimization method is proposed for an optimized aerodynamic design of a hypersonic vehicle. As part of this approach, a constrained experimental design method is developed to handle the constraints more efficiently. A radial basis function is used to surrogate time-consuming CFD analysis. An efficient and more robust numerical mesh morphing scheme for the hypersonic vehicle is developed for the generation of high-quality meshes. Within this paper, a novel adaptive infilling strategy is proposed which uses an inaccurate search technique coupled with an elite archive. This allows the location of a more promising sample region and hence improves the surrogate accuracy, thereby further enhancing the optimization efficiency. A hypersonic vehicle aerodynamic design problem is solved using the proposed approach and satisfactory results are obtained at much lower computational costs. The lift-to-drag ratio is increased by 23.8% when compared with the base configuration while also satisfying the volume and lift constraints. The pressure and Mach contours have been compared with those of the base configuration and the results demonstrate the strength of the optimized configuration. The modified sequential approximate optimization for designing an improved hypersonic vehicle is worth referencing in future work.     

用自联想网络处理带噪声的发动机数据

研究了用自联想网络(AANN)进行数字滤波的方法。自联想网络采用一种带有瓶颈层的特殊结构，且具有单位总增益。在经过大量带噪声样本的训练之后，各变量之间能够建立起内在联系。输入信息通过瓶颈层前的压缩及瓶颈层后的解压缩过程，信息中的精华将被提取，从而使人们能够利用冗余信息抑制其测量噪声，使发动机测量参数在最大程度上减少噪声对其带来的负面影响。     

压杆稳定可靠性稳健设计

将稳定可靠性优化理论、稳定可靠性灵敏度技术与稳健设计方法相结合,讨论压杆稳定可靠性稳健设计问题,提出了稳定可靠性稳健设计的计算方法。把可靠性灵敏度溶入可靠性优化设计模型之中,将可靠性稳健设计归结为满足可靠性要求的多目标优化问题。数值算例表明所提数值计算方法是一种非常方便和实用的可靠性稳健设计方法。     

某型飞机空中飘摆故障分析及防护措施

分析某型飞机平尾助力器故障导致飞机在空中飞行时产生飘摆现象的原因,提出修理改进措施及维护对策。     

航空复合材料纸蜂窝夹芯结构热成型开裂研究

飞机复合材料芳纶纸蜂窝夹芯部件在热压罐成型时处于热-力耦合工况。本文关注热成型过程中可能出现的蜂窝开裂现象,通过试验获得了蜂窝芯的拉、压、剪性能参数和芳纶纸的热性能参数,同时结合有限元分析手段和反演方法,对整体蜂窝夹芯部件的热-力顺序耦合和局部芯子抽真空导致的蜂窝胞元间压强差进行数值模拟。结果表明：成型过程中的热应力不会导致蜂窝胞元间胶层开裂,局部憋气的压差可能导致蜂窝开裂;胶层部分破坏与胶层完全破坏所需的胞元间压强差的差值与胶层初始法向断裂应力正相关;胶层完全破坏所需的胞元间压强差随着受载胞元数量的增多而减小。     

基于典型飞行任务的CCA技术优势分析

基于典型飞行任务,在F-119发动机方案的循环参数基础上,对采用冷却冷却空气（CCA）技术的航空发动机性能开展研究,分析CCA技术对发动机总体性能及涡轮叶片温度的影响规律,评估采用CCA技术的涡扇发动机对其所装配飞机的飞行性能的影响。结果表明：针对仅预冷高压涡轮动叶冷却气方案,当保持冷却空气流量不变时,采用CCA技术可将涡轮冷气温度降低16.98%~41.21%,使得高压涡轮动叶表面最高温度降低8.89%~16.80%;当保持叶片表面最高温度不变时,采用CCA技术可减少高压涡轮动叶48.61%的冷却用气,且发动机的推力和耗油率等总体性能基本不变;针对同时预冷高压涡轮导叶和动叶冷却气方案,通过调整循环参数,在保持冷却空气流量和叶片温度不变的前提下,可使涡轮前最高温度提高6.91%,从而提高典型飞行状态下的航发推进性能,进而有效提升所配装飞机的起飞载质量、最大爬升率、最大马赫数、使用升限及航程等飞行性能。     

不同温度下树脂基复合材料层合板力学性能试验

通过试验的方法研究了双马来酰亚胺树脂浇注体及碳纤维增强树脂基复合材料单向层合板在不同温度下的静态力学性能,并讨论了温度对材料力学行为的影响,最后对材料断口形貌进行了分析.试验结果表明:纯树脂浇注体拉伸、压缩性能受温度影响比较明显,且拉、压性能不同.对于拉伸性能,相对室温均值(20℃),160℃环境下模量均值及强度均值降幅分别为31.73%,44.71%,200℃时又分别下降了21.15%,20.37%;对于压缩性能,相对室温均值,160℃下模量及强度均值分别下降了26.67%,44.40%,而200℃时继续下降了6.66%,12.40%.层合板的纵向拉伸性能受温度影响较小,在200℃内,纵向模量与强度最大变幅分别为2.82%和2.53%,且材料断口从室温下的"毛刷"状变为了沿轴向劈断.材料的横向及面内剪切性能受温度影响较大,且应力-应变曲线存在明显非线性,但横向试件断口平整、面内剪切试件无明显紧缩现象,即均表现为脆性断裂特征.另外,相对室温均值,在160℃时,横向及面内切变模量分别下降约32.96%,41.25%,强度分别下降约15.83%,30.96%;在200℃时,横向及面内剪切性能继续下降,模量降幅为16.83%,22.52%,强度降幅12.24%,11.01%.      

基于集对分析的航空装备维修安全综合评估

针对航空装备维修安全的评估问题,建立了航空装备维修安全评估指标体系,运用集对分析法对航空装备维修安全进行评估,详细描述了利用该方法进行评价的基本步骤。通过分析计算和实例应用中可以看出,该模型原理直观、计算简便、结果客观实际,有利于部队决策机关掌握航空装备维修安全情况,科学指导训练工作,更好地实施信息化条件下的战机保障。