压力振荡对气液同轴离心式喷嘴自激振荡的影响

为了研究供应系统振荡对气液同轴离心式喷嘴自激振荡的影响,采用水和空气作为模拟介质,开展了室压条件下冷态喷雾试验。通过试验分析了供应系统有/无振荡两种情况下离心式喷嘴的喷雾形态,以及供应系统有/无振荡两种情况下气液同轴离心式喷嘴自激振荡的喷雾形态。发现当离心式喷嘴供应系统振荡时,离心式喷嘴产生的锥形液膜也周期性地振荡,同时出现Klystron效应。液膜周期性振荡以及Klystron效应出现的频率与供应系统振荡频率一致。Klystron效应的出现使得喷雾锥角突然减小,锥形液膜发生折叠。供应系统振荡对自激振荡喷雾形态也有显著影响。供应系统振荡引起的Klystron效应使得液膜锥角减小,从而造成"圣诞树"型自激振荡喷雾上的"树枝"增多,同时自激振荡频率增加。这是因为当速度大的液膜追上速度小的液膜时,就会产生Klystron效应并使液膜速度增加。而液膜运动速度越大自激振荡频率也就越大。虽然在供应系统中施加激励没有发生"锁频"现象,但是自激振荡的强度在一定程度上减弱,并且伴随着自激振荡的"分频"现象,即自激振荡频率从一个主频向两侧分化为两个主频。     

基于视觉注意机制的认知雷达数据关联算法

针对传统关联波门设计方法在应用于机动目标跟踪时容易引起失跟、以及概率数据关联算法不适于多交叉目标跟踪的问题,提出了一种基于人类视觉选择性注意机制和知觉客体的"特征整合"理论的认知雷达数据关联算法。算法以综合交互式多模型概率数据关联算法为基础,采取假设目标最大机动水平已知的"当前"统计模型和匀速运动模型作为模型集,通过实时交互使关联波门能够随目标机动动态调整,较好地兼顾了雷达计算耗时和跟踪成功率。在利用目标位置特征的基础上,进一步提取、整合目标运动特征,对关联波门交叉区域公共量测进行分类,使多交叉目标跟踪问题转化为多个单目标跟踪问题,优化了传统概率数据关联算法。仿真结果表明：与传统关联波门设计方法相比,算法跟踪失败率和计算耗时明显降低;而且在计算资源增加不大的情况下,杂波环境适应性也得到了显著增强。     

多电极偶接对金属大气腐蚀影响的试验与仿真

搭建薄液膜厚度测量与控制装置,采用微距参比电极后置法组建三电极体系,测量了厚度为100 μm的3.5wt% NaCl液膜下2A12铝合金、TC18钛合金和30CrMnSiNi2A高强钢的极化曲线和耦合体系的电偶电流;建立了基于薄壳电流分布的Comsol腐蚀仿真模型,得到了100 μm液膜下电极电位分布和电流密度分布图,通过对电极表面进行局部电流面积分计算得到了其电偶电流,对不同电极进行了面积的参数化扫描,讨论分析了不同面积比对于电偶电流的影响。结果表明：利用仿真模型得到的电偶电流值与试验值吻合较好,在2A12/30CrMnSiNi2A/TC18多电极体系中2A12充当阳极,TC18/30CrMnSiNi2A充当阴极,且阴阳极极性不随面积比的变化而发生转变,电偶电流主要集中在30CrMnSiNi2A与2A12之间,电偶电流与TC18面积呈线性关系,其对数与2A12和30CrMnSiNi2A面积的对数之间呈线性关系。利用建立的仿真模型对模拟搭接件大气腐蚀进行了仿真研究,仿真发现垫圈、2A12与30CrMnSiNi2A偶接接缝处及2A12与TC18偶接铆钉处电流密度分布更为集中,易发生腐蚀,与暴晒试验结果相符,说明该仿真模型对于多电极偶接的腐蚀分布具有很好的预测作用。     

航空发动机机匣摆线粗加工轨迹规划方法

针对机匣零件粗加工过程中凸台多、加工余量大、材料难切削、刀具磨损快、加工周期长等特点,提出了一种机匣摆线粗加工刀具轨迹规划方法,该方法能有效控制切削过程中刀具负载的变化,改善刀具切削过程中的加热-冷却循环,减缓刀具的磨损,提高机匣粗加工效率。首先,通过对两种摆线模型的分析,建立了摆线铣数学模型,并分析了摆线铣的优缺点;其次,结合机匣零件特点,将模型在精度范围内离散为点模型,利用圆锥将模型展开并建立展开模型与原始模型间的映射关系。通过对可加工区域的划分和平面逼近,生成了适用于机匣零件的摆线粗加工刀具轨迹。最后,分别通过摆线铣刀具磨损实验、平面型腔摆线铣实验和机匣摆线铣实验,验证了摆线铣在降低刀具磨损、延长刀具寿命方面的有效性,以及本文轨迹生成算法在航空发动机机匣实际加工中的正确性和高效性。研究成果能有效缩短加工周期、降低加工成本,提升机匣零件的粗加工效率。     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

A two-step weighted least-squares method for joint estimation of source and sensor locations: A general framework

It is well known that the Two-step Weighted Least-Squares(TWLS) is a widely used method for source localization and sensor position refinement. For this reason, we propose a unified framework of the TWLS method for joint estimation of multiple disjoint sources and sensor locations in this paper. Unlike some existing works, the presented method is based on more general measurement model, and therefore it can be applied to many different localization scenarios.Besides, it does not have the initialization and local convergence problem. The closed-form expression for the covariance matrix of the proposed TWLS estimator is also derived by exploiting the first-order perturbation analysis. Moreover, the estimation accuracy of the TWLS method is shown analytically to achieve the Cramér-Rao Bound(CRB) before the threshold effect takes place. The theoretical analysis is also performed in a common mathematical framework, rather than aiming at some specific signal metrics. Finally, two numerical experiments are performed to support the theoretical development in this paper.     

基于最小约束系统的分布式协作定位研究

5G移动通信系统中,设备到设备的通信方式产生了节点间的信号测量,可用于提升无线定位的覆盖范围和定位精度。提出了一种基于最小约束系统的分布式协作定位方法,该方法首先利用已有算法估计节点参考位置,并据此构建最小约束确定网络的位置及朝向,然后在该约束下极大化由节点间测量引出的似然函数,获得位置估计。理论研究表明,该方法将由节点间测量确定的相对位置拟合到参考位置处,在参考位置等于真实位置时达到最优效果。仿真结果表明,该方法可有效提高定位精度,并具有分布式和可扩展等优点。     

燃气轮机燃烧室预混喷嘴排放性能的试验和数值研究

为了研究当量比、值班燃料量和压力对燃气轮机燃烧室预混喷嘴排放指标的影响,在环境压力下按照等速模化原理进行了燃烧室预混喷嘴的燃烧试验,基于化学反应网络法构建了污染物预测模型,开展了试验和数值对比研究。结果表明:在带值班燃料的情况下该预混喷嘴当量比φ在0.35～0.5时可满足国标排放要求,但是值班燃料量增大会使NO_x排放升高;在φ0.4时,压力对纯预混燃烧NO_x生成无影响,φ0.4时,NO_x会随压力升高而增多;带有值班燃料的预混燃烧时,NO_x对压力变化敏感,压力升高导致NO_x增多;该预混喷嘴混合性能对空气流速不敏感、燃料兼容性强,排放达标当量比范围宽,经进一步设计开发后有潜力应用于燃气轮机低排放燃烧室中。该化学反应器网络模型依赖经验较少,当值班燃料比例≤0.17时,对污染物预测与试验数据符合较好。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

水平导航中转弯航线解算方法的研究和仿真

在飞机显示器的水平导航区域上需要为飞行员实时显示最新的航线信息,航线中的每个航路点均有不同的转弯方式,目前国内正在研发的飞机采用旁切转弯和飞越转弯两种方式,若错过了预计的转弯起始点,则需要重新进行航线解算,这被定义为超调转弯,给出三类转弯航线的解算方法。