基于双变量预测控制的表贴式永磁同步电机直接转矩控制系统

基于电压矢量幅值和相角为变量的表贴式永磁同步电机(SPMSM)定子磁链幅值和转矩表达式,给出了9个不同幅值和相角的备选电压矢量,采用预测控制计算得出施加不同电压矢量下一时刻的定子磁链幅值和转矩值,建立了基于磁链和转矩误差的目标函数,并选择使目标函数最小的电压矢量为作为下一时刻施加的最优电压矢量。仿真结果表明:在双变量预测控制下,SPMSM直接转矩控制系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。进一步对比分析表明:与开关表和固定电压矢量选择策略相比,双变量预测控制能显著减小转矩和磁链脉动。与开关表相比,转矩脉动均方根误差降低了62.92%,磁链脉动均方根误差降低了45.05%,评价函数均值降低了60.30%;与固定电压矢量选择策略相比,转矩脉动均方根误差降低了22.40%,磁链脉动均方根误差降低了3.85%,评价函数均值降低了15.93%。     

基于二阶滑模算法的永磁电机直接转矩控制

针对传统直接转矩控制(DTC)方法低速控制精度差、转矩脉动大、开关频率不稳定等问题,提出了一种基于二阶滑模控制的永磁电机DTC方法。该控制方法基于二阶滑模控制原理,将传统磁链控制器与转矩控制器以滑模控制器替代,对空间电压进行矢量调制,提高了开关频率的稳定性,获得了良好的动态稳定性,改善了电机输出性能。仿真与试验结果表明,该控制方法能够有效减小电流脉动与转矩脉动,同时提高了控制系统的抗干扰能力,实现了电机的快速动态响应,具有较强的鲁棒性能。     

Deformation behavior of non-rigid airships in wind tunnel tests

Deformation behavior of non-rigid airships in wind tunnel tests is studied by considering three factors, including internal pressure, flow velocity and angle of attack. Fiber Bragg grating strain sensors are used to measure the deformation of non-rigid airships. Wind tunnel tests in the case of different flow velocities and angles of attack are conducted. The measurement results reveal that the airship deformation is in proportion to internal pressure. For the tensile region,the airship deformation is in proportion to flow velocity. Effects of angle of attack on structural deformation are more complicated and there is no clear relationship existing between airship deformation and angle of attack.     

Dynamics and de-spin control of massive target by single tethered space tug

This paper investigates the dynamics and de-spin control of a massive target by a single tethered space tug in the post-capture phase. The dynamic model of the tethered system is derived and simplified to a dimensionless form. Further, a decoupled PD controller is proposed, and the local stability of the controller is analyzed by linearization technique. Parametric studies of the dynamics and de-spin control of a massive target are conducted to characterize the dynamic process of de-spin with the proposed control law. It is shown that the massive target can be de-span by a single and small space tug with limited thrust within finite time. The thrust tangent with the tether de-spins the target while the thrust normal to the tether prevents the tether from winding up the target. The tether length has a positive contribution to the de-spin of a target. The longer tether leads to a faster de-spin process.     

Special Column:NDT and SHM in Aerospace

<正>Non-Destructive Testing and Structural Health Monitoring(NDT SHM) is one of the major requirements in aerospace structural design and plays an important role in operation and maintenance of aerospace structures. NDT SHM is a technology dealing     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

摆线桨非定常动态失速的三维效应

对摆线桨三维全尺寸模型进行了非定常数值模拟。验证了两种嵌套网格方法的可靠性与适用性,针对二维/三维情况下摆线桨非定常涡流动特性及诱导分离特性开展了数值分析,重点研究了展向气动力随方位角的分布与全局流场的诱导速度分布,并分析了尾迹捕捉精度与涡量耗散特征。结果表明:受摆线桨切向速度、展向诱导速度等三维效应影响,两种计算结果的瞬态气动力极值差值达到44%。三维动态失速涡的产生、脱落与再附明显弱于二维翼型情况,这对于摆线桨非定常气动特性有较大影响。      

纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

直线电机位置伺服系统的增强复合非线性控制

针对高性能机电系统中常用的直线伺服电机,设计了一个能实现快速与准确的定点运动的位置控制器。控制器采用线性控制律与平滑非线性控制律相结合的方案,并利用一个降阶线性状态观测器对电机运动速度(未量测)加以估计。为了消除未知扰动带来的稳态误差,控制律中嵌入了积分控制作用。整个控制律采用全参数化设计,可实现动态增益控制,方便了在线参数整定与性能优化。控制方案应用于一个实际的永磁直线电机位置伺服系统,基于TMS320F28335 DSC进行了试验测试,结果表明系统能对各目标位置进行准确的跟踪,且具有理想的瞬态性能。     

应用于超级电容储能系统的双向DC/DC变换器混沌控制方法研究

超级电容储能系统(SCESS)主要通过对双向DC/DC变换器进行控制来快速平抑直流母线电压的波动。为了抑制控制过程中所产生的一些分岔和混沌现象,提出了一种应用于SCESS的混沌控制方法。分析了该方法的控制原理,并根据非线性动力学理论建立了双向DC/DC变换器的离散迭代模型;然后设计了一种能够自动调节补偿斜率的混沌控制信号;最后对该信号作用下的异步切换函数和同步切换映射式进行了数值求解,从而绘出系统分叉图。通过仿真和试验证明,该方法能够有效抑制SCESS的分岔和混沌现象,提高了系统的稳定工作范围和动态响应速度。