Ultracapacitors + DC-DC converters in regenerative braking system

An ultracapacitor system for an electric vehicle has been implemented. The device allows higher accelerations and decelerations of the vehicle with minimal loss of energy and minimal degradation of the main battery pack. The system uses a DC-DC power converter, which is connected between the ultracapacitor and the main battery pack. The design has been optimized in weight and size, by using water-cooled heat sinks for the power converter, and an aluminum coil with air core for the smoothing inductance. The ratings of the ultracapacitor are: nominal voltage: 300 Vdc; nominal current: 200 Adc; capacitance: 20 Farads. The amount of energy stored allows us to have 40 kW of power during 20 seconds, which is enough to accelerate the vehicle without the help of the traction batteries. The vehicle uses a brushless DC motor with a nominal power of 32 kW and a peak power of 53 kW. A control system based on a Digital Signal Processor (DSP) manipulates all the aforementioned variables and controls the Pulse Width Modulation (PWM) switching pattern of the converter transistors. The car used for the implementation of this system is a Chevrolet LUV truck.     

Energy storage at 77 K in multilayer ceramic capacitors

A ceramic material having a large dielectric constant at 77 K, ε=8000-12000, has been developed for capacitive energy storage at this temperature. A large matrix of multilayer ceramic capacitors were fabricated using conventional tape-casting methods to optimize the dielectric breakdown strength at 77 K, and measured energy storage values on these capacitors range up to 6 J/cm³ at 77 K. An unfused bank of these capacitors was voltage-cycled 10⁵ times at 77 K without failure, and the heating effects during cycling were immeasurably small (i.e., nitrogen boiloff was monitored). An electrocaloric effect on discharge (ΔT~1 K) contributes to the thermal stability. Measurements of the frequency dependence of the dielectric properties of the ceramic at 77 K indicate a fundamental limit of about 8 μs for the switching repetition rate. Improved capacitor-manufacturing methods are discussed which can increase the energy density to the 20-30 J/cm³ range     

Moving target imaging algorithm for SAR data

A digital processing algorithm for fine-resolution imaging of synthetic aperture radar (SAR) moving targets is described. The targets may have any translational and rotational motion components relative to the data collection platform. The algorithm requires the presence of up to three prominent points in the image of the target; the signals from these points provide estimates of the unknown target motion parameters. Phase compensation and data formatting based on these estimates eliminate motion-induced phase errors. This algorithm has been implemented on a VAX computer and used to process both simulated and real SAR data of moving targets. Results obtained using the simulated data are presented     

Experimental phased array radar ELRA with extended flexibility

An update of a phased array radar project with the experimental system ELRA (electronic steerable radar) is given with respect to the extended and improved possibilities for performing measurements and evaluations for different types of radar operation. The variability of waveforms for solid-state transmitters is described. Flexible control of multifunction operation with various search and localization tasks is achieved with a network of microcomputers. Different means of signal processing are used for target detection and estimation. The active receiving array is divided into subarrays, and offers digital beamforming for pattern shaping and adaptive jammer suppression. Experimental results are presented     

STEREO Ground Segment, Science Operations, and Data Archive

Vitally important to the success of any mission is the ground support system used for commanding the spacecraft, receiving the telemetry, and processing the results. We describe the ground system used for the STEREO mission, consisting of the Mission Operations Center, the individual Payload Operations Centers for each instrument, and the STEREO Science Center, together with mission support from the Flight Dynamics Facility, Deep Space Mission System, and the Space Environment Center. The mission planning process is described, as is the data flow from spacecraft telemetry to processed science data to long-term archive. We describe the online resources that researchers will be able to use to access STEREO planning resources, science data, and analysis software. The STEREO Joint Observations Program system is described, with instructions on how observers can participate. Finally, we describe the near-real-time processing of the “space weather beacon” telemetry, which is a low telemetry rate quicklook product available close to 24 hours a day, with the intended use of space weather forecasting.     

Further comments on “Optimal sensor selection strategy fordiscrete-time estimators” [and reply]

The fundamental TPBVP usually underlying true “optimal sensor selection strategy” is revisited to obtain practical real-time mechanizations as a solution to an exclusively initial value problem     

Designing planetary protection into the Mars Observer mission.

Planetary protection has been an important consideration during the process of designing the Mars Observer mission. It affected trajectory design of both the interplanetary transfer and the orbits at Mars; these in turn affected the observation strategies developed for the mission. The Project relied mainly on the strategy of collision avoidance to prevent contamination of Mars. Conservative estimates of spacecraft reliability and Martian atmosphere density were used to evaluate decisions concerning the interplanetary trajectory, the orbit insertion phase at Mars, and operations in orbit at Mars and afterwards. Changes in the trajectory design, especially in the orbit insertion phase, required a refinement of those estimates.