钛合金表面镍包石墨喷涂层的耐磨性能

为了提高钛合金的表面耐磨性,利用氧乙炔热喷涂枪,在TC4合金表面上制备出镍包石墨涂层。采用MXP-2000型销盘式摩擦磨损实验机,进行钛合金及其镍包石墨涂层的干摩擦磨损实验,并利用扫描电镜对磨损表面进行观察和分析。实验结果发现,镍包石墨涂层的摩擦系数只有钛合金的一半左右,前者磨损量为后者的1/6,说明镍包石墨涂层可以大大提高钛合金的表面耐磨性能。TC4合金的磨损机制以黏着磨损为主,喷涂层的磨损机制以磨粒磨损为主,喷涂层中的石墨润滑相是其耐磨性高的主要原因。     

SBS改性再生型木塑复合材料及其耐水性能

为了充分利用城市固体废弃物中的各项资源，本项工作将固体废弃物中的高密度聚乙烯（HDPE）回收后与废弃的木纤维、苯乙烯-丁二烯-苯乙烯（SBS）进行复合，成功地制备出SBS／再生型木塑复合材料，并进行了力学性能测试和水煮试验。结果表明，SBS的加入使木塑复合材料的冲击韧性得到显著改善，同时，复合材料的弯曲强度和弯曲模量没有明显的影响，表明SBS可以作为木塑复合材料的增韧剂。SBS／木塑复合材料经过8周、60℃的水煮后，复合材料的吸水率和厚度膨胀率均有所增加，弯曲模量和冲击韧性分别平均下降14．4％、10．8％。水煮试验初期复合材料的弯曲强度逐渐降低，然后又逐渐增大，第8周后弯曲强度增加的幅度约10％。木塑复合材料的冲击破坏模式以界面脱粘为主，而加入SBS后，复合材料的破坏以纤维断裂和基体断裂为主。     

复合材料锥壳0°铺层的自动铺放成型方法研究

研究了一种基于自动铺带技术的复合材料锥壳0°铺层成型方法：根据锥壳构件尺寸将等宽预浸带数控分切成预定尺寸的直角梯形预浸带片，按特定方式铺放到锥壳表面并使每两片拼成一个等腰梯形单元，多个等腰梯单元形构成锥壳的0°铺层；并针对这种成型方法设计了一种实现锥壳0°铺层自动成型的装置。采用该方法及其设备可以实现锥壳0°铺层的自动化制造，提高成型效率、降低废料率、稳定工艺质量，降低装备制造成本。     

DA4169合金高温疲劳裂纹扩展速率

实验研究了直接时效ＤＡ４１６９合金５５０℃、６５０℃下的疲劳裂纹扩展行为，并进行了带上峰值保持时间的试验。结果表明：连续循环的ｄａ／ｄＮ值基本上与普通４１６９的相当，但在６５０℃下略优；６５０℃带上峰值保时１５ｓ的ｄａ／ｄＮ值比连续循环的大大加速。     

粒子云侵蚀问题实验研究中动能通量模拟的意义

本文首先将粒子云侵蚀条件下的驻点表面后退分解为无粒子烧蚀部分、粒子云引起的烧蚀增量部分和粒子撞击物面引起的直接侵蚀部分。然后研究了表面能量平衡关系,给出了粒子云引起的烧蚀增量表达式。最后分三类讨论粒子与飞行器的碰撞:(1)完全弹性碰撞(不符合实际);(2)完全非弹性碰撞;(3)部分弹性碰撞。对于后两种碰撞,本文分析了动能通量模拟适用的条件。     

Evaluating a multiple-hypothesis multitarget tracking algorithm

The performance evaluation of multiple-hypothesis, multitarget tracking algorithm is presented. We are primarily interested in target-detection/track-initiation capabilities as measures of performance. Through Monte Carlo simulations, a multiple-hypothesis tracking algorithm was evaluated in terms of 1) probability of establishing a track from target returns and 2) false track density. A radar was chosen as the sensor, and a general multiple-hypothesis, multitarget tracking algorithm was used in the Monte Carlo simulations. The simulation results predict the probability of establishing a track from returns of a target as well as the false track density per scan volume per unit time. The effects of the target radar cross section and the radar power, measured through the mean signal-to-noise ratio (SNR) were studied, as were the effects of detection threshold and track quality threshold. Computational requirements were also investigated     

高速滚子轴承运动特性的动态模拟

在高速轻载的工况下 ,滚子轴承的打滑蹭伤及由于滚子歪斜引起的滚子端面磨损已成为滚子轴承的主要失效原因。本文根据牛顿运动定律 ,建立了滚子的动力学模型 ,并对滚子轴承径向载荷分布和油膜拖动力的计算进行了详细讨论。利用本文所编制的软件 ,对滚子和保持架的打滑以及滚子的歪斜运动进行了动态模拟 ,得到与实际相符的结果 ,可用为实际轴承设计。     

EXPERIMENTAL RESEARCH ON STRESS INTENSITY FACTOR K_Ⅲ FOR 3-D CRACK BY CAUSTICS

ＥＸＰＥＲＩＭＥＮＴＡＬＲＥＳＥＡＲＣＨＯＮＳＴＲＥＳＳＩＮＴＥＮＳＩＴＹＦＡＣＴＯＲＫⅢＦＯＲ３┐ＤＣＲＡＣＫＢＹＣＡＵＳＴＩＣＳＷｕＤａｆａｎｇ，ＧａｏＺｈｅｎｔｏｎｇ（ＩｎｓｔｉｔｕｔｅｏｆＳｏｌｉｄＭｅｃｈａｎｉｃｓ，ＢｅｉｊｉｎｇＵｎｉｖｅ...     

A relative navigation system for formation flight

A relative navigation system based on both the Inertial Navigation System (INS) and the Global Positioning System (GPS) is developed to support situational awareness during formation flight. The architecture of the system requires an INS/GPS integration across two aircraft via a data link. A fault-tolerant federated filter is used to estimate the relative INS errors based on relative GPS measurements and a range measurement obtained from the data link. The filter is constructed based on a reduced-order model of the relative INS error process. A method for analyzing the filter performance is presented. A case involving two helicopters in formation flight is studied under three different night trajectories to account for the effect of vehicle motion on the INS state transition matrix. The results of the covariance analysis are compared with actual night results over an instrumented test range.     

预估校正的高分辨率格式及其应用

本文从基于通量分裂的一阶迎风格式出发,构造了一类校正型具有高分辨瘁的二阶全变差递减(TVD)格式,并用此格式进行了一维激波管问题及二维问题的计算。结果表明格式的解为二阶精度,激波处无明显的振荡,激波过渡区为1～2个点。