Expectations for Infrared Spectroscopy of 9P/Tempel 1 from Deep Impact

The science payload on the Deep Impact mission includes a 1.05–4.8 μm infrared spectrometer with a spectral resolution ranging from R∼200–900. The Deep Impact IR spectrometer was designed to optimize, within engineering and cost constraints, observations of the dust, gas, and nucleus of 9P/Tempel 1. The wavelength range includes absorption and emission features from ices, silicates, organics, and many gases that are known to be, or anticipated to be, present on comets. The expected data will provide measurements at previously unseen spatial resolution before, during, and after our cratering experiment at the comet 9P/Tempel 1. This article explores the unique aspects of the Deep Impact IR spectrometer experiment, presents a range of expectations for spectral data of 9P/Tempel 1, and summarizes the specific science objectives at each phase of the mission.     

Deep Impact: Working Properties for the Target Nucleus – Comet 9P/Tempel 1

In 1998, Comet 9P/Tempel 1 was chosen as the target of the Deep Impact mission (A’Hearn, M. F., Belton, M. J. S., and Delamere, A., Space Sci. Rev., 2005) even though very little was known about its physical properties. Efforts were immediately begun to improve this situation by the Deep Impact Science Team leading to the founding of a worldwide observing campaign (Meech et al., Space Sci. Rev., 2005a). This campaign has already produced a great deal of information on the global properties of the comet’s nucleus (summarized in Table I) that is vital to the planning and the assessment of the chances of success at the impact and encounter. Since the mission was begun the successful encounters of the Deep Space 1 spacecraft at Comet 19P/Borrelly and the Stardust spacecraft at Comet 81P/Wild 2 have occurred yielding new information on the state of the nuclei of these two comets. This information, together with earlier results on the nucleus of comet 1P/Halley from the European Space Agency’s Giotto, the Soviet Vega mission, and various ground-based observational and theoretical studies, is used as a basis for conjectures on the morphological, geological, mechanical, and compositional properties of the surface and subsurface that Deep Impact may find at 9P/Tempel 1. We adopt the following working values (circa December 2004) for the nucleus parameters of prime importance to Deep Impact as follows: mean effective radius = 3.25± 0.2 km, shape – irregular triaxial ellipsoid with a/b = 3.2± 0.4 and overall dimensions of ∼14.4 × 4.4 × 4.4 km, principal axis rotation with period = 41.85± 0.1 hr, pole directions (RA, Dec, J2000) = 46± 10, 73± 10 deg (Pole 1) or 287± 14, 16.5± 10 deg (Pole 2) (the two poles are photometrically, but not geometrically, equivalent), Kron-Cousins (V-R) color = 0.56± 0.02, V-band geometric albedo = 0.04± 0.01, R-band geometric albedo = 0.05± 0.01, R-band H(1,1,0) = 14.441± 0.067, and mass ∼7×10¹³ kg assuming a bulk density of 500 kg m⁻³. As these are working values, {i.e.}, based on preliminary analyses, it is expected that adjustments to their values may be made before encounter as improved estimates become available through further analysis of the large database being made available by the Deep Impact observing campaign. Given the parameters listed above the impact will occur in an environment where the local gravity is estimated at 0.027–0.04 cm s⁻² and the escape velocity between 1.4 and 2 m s⁻¹. For both of the rotation poles found here, the Deep Impact spacecraft on approach to encounter will find the rotation axis close to the plane of the sky (aspect angles 82.2 and 69.7 deg. for pole 1 and 2, respectively). However, until the rotation period estimate is substantially improved, it will remain uncertain whether the impactor will collide with the broadside or the ends of the nucleus.     

Robust algorithm for combating look direction error problems

A simple and fast zero tracking algorithm for adaptive arrays with large look direction errors is presented and investigated. Basically, the algorithm is based on adjusting the complex zeroes of a power inversion array in a time-multiplexed manner to track all the sources in the environment. To preserve the desired signal which is supposed to be closest to the look direction of 0°, the algorithm removes the zero with the shortest distance to e^j0 so that the directional response consists of only nulls steered at the jammers. When compared with the least mean square (LMS) algorithm employing zeroth and first-order look direction constraints, the new algorithm has about the same implementation complexity, is considerably faster, and possesses a much better signal-to-noise ratio (SNR) performance when the look direction is erroneous     

The Apollo SWC Experiment: Results,Conclusions, Consequences

Space Science Reviews - The Apollo Solar Wind Composition (SWC) experiment was designed to measure elemental and isotopic abundances of the light noble gases in the solar wind, and to investigate...     

Variations of the magnetic fields in large solar flares

We present preliminary results from high resolution observations obtained with the Michelson Doppler Imager (MDI) instrument on the SOHO of two large solar flares of 14 July 2000 and 24 November 2000. We show that rapid variations of the line-of-sight magnetic field occured on a time scale of a few minutes during the flare explosions. The reversibility/irreversibility of the magnetic field of both active regions is a very good tool for understanding how the magnetic energy is released in these flares. The observed sharp increase of the magnetic energy density at the time of maximum of the solar flare could involve an unknown component which deposited supplementary energy into the system. This revised version was published online in August 2006 with corrections to the Cover Date.     

Huygens Probe Aerosol Collector Pyrolyser Experiment

ACP's main objective is the chemical analysis of the aerosols in Titan's atmosphere. For this purpose, it will sample the aerosols during descent and prepare the collected matter (by evaporation, pyrolysis and gas products transfer) for analysis by the Huygens Gas Chromatograph Mass Spectrometer (GCMS). A sampling system is required for sampling the aerosols in the 135'32 km and 22'17 km altitude regions of Titan's atmosphere. A pump unit is used to force the gas flow through a filter. In its sampling position, the filter front face extends a few mm beyond the inlet tube. The oven is a pyrolysis furnace where a heating element can heat the filter and hence the sampled aerosols to 250 °C or 600 °C. The oven contains the filter, which has a thimble-like shape (height 28 mm). For transferring effluent gas and pyrolysis products to GCMS, the carrier gas is a labeled nitrogen ¹⁵N₂, to avoid unwanted secondary reactions with Titan's atmospheric nitrogen. Aeraulic tests under cold temperature conditions were conducted by using a cold gas test system developed by ONERA. The objective of the test was to demonstrate the functional ability of the instrument during the descent of the probe and to understand its thermal behavior, that is to test the performance of all its components, pump unit and mechanisms. In order to validate ACP's scientific performance, pyrolysis tests were conducted at LISA on solid phase material synthesized from experimental simulation. The chromatogram obtained by GCMS analysis shows many organic compounds. Some GC peaks appear clearly from the total mass spectra, with specific ions well identified thanks to the very high sensitivity of the mass spectrometer. The program selected for calibrating the flight model is directly linked to the GCMS calibration plan. In order not to pollute the two flight models with products of solid samples such as tholins, we excluded any direct pyrolysis tests through the ACP oven during the first phase of the calibration. Post probe descent simulation of flight results are planned, using the much representative GCMS and ACP spare models. This revised version was published online in August 2006 with corrections to the Cover Date.     

Comet Geology with Deep Impact Remote Sensing

The Deep Impact mission will provide the highest resolution images yet of a comet nucleus. Our knowledge of the makeup and structure of cometary nuclei, and the processes shaping their surfaces, is extremely limited, thus use of the Deep Impact data to show the geological context of the cratering experiment is crucial. This article briefly discusses some of the geological issues of cometary nuclei.     

Acceleration of the solar wind

In this review, we discuss critically recent research on the acceleration of the solar wind, giving emphasis to high-speed solar wind streams emanating from solar coronal holes. We first explain why thermally driven wind models constrained by solar and interplanetary observations encounter substantial difficulties in explaining high speed streams. Then, through a general discussion of energy addition to the solar wind above the coronal base, we indicate a possible resolution of these difficulties. Finally, we consider the question of what role MHD waves might play in transporting energy through the solar atmosphere and depositing it in the solar wind, and we conclude by examining, in a simple way, the specific mechanism of solar wind acceleration by Alfvén waves and the related problem of accelerating massive stellar winds with Alfvén waves.Paper presented at the IX-th Lindau Workshop The Source Region of the Solar Wind.On leave from the Auroral Observatory, Institute of Mathematical and Physical Sciences, University of Tromsø, N-9001 Tromsø, Norway.The National Center for Atmospheric Research is sponsored by the National Science Foundation.     

An optimum filter for direct A/D conversion

The author describes a design procedure to find the optimum finite-impulse-response (FIR) filter coefficients when the characteristics of the bandpass filter preceding the analog-to-digital (A/D) converter are known. A simulation of direct A/D conversion performance shows the improvement over the filter coefficients designed to minimize the maximum error over a specified band of frequencies. DC cancellation may be added to the process with very little change in the coefficients of the optimum FIR filter or its performance.<>     

Stochastic Dynamic System Suboptimal Control with Uncertain Parameters

The control of a linear system with random coefficients is studied here. The cost function is of a quadratic form and the random coefficients are assumed to be partially observable by the controller. By means of the stochastic Bellman equation, the optimal control of stochastic dynamic models with partially observable coefficients is derived. The optimal control is shown to be a linear function of the observable states and a nonlinear function of random parameters. The theory is applied to an optimal control design of an aircraft landing in wind gust.