碳纤维复合材料承力筒长桁预制工艺技术

叙述了某型号卫星碳纤维复合材料承力筒长桁预制件的研制技术。运用介电损耗仪研究树脂基体在固化过程中的性能变化,以确定预浸料吸胶及预制件预压的工艺规范。预制件的成型采用软硬模相结合的方法,所研制的长桁预制件的性能满足了碳承力筒研制总工艺的要求,并通过了碳承力筒的地面力学性能试验。     

Overview of the New Horizons Science Payload

The New Horizons mission was launched on 2006 January 19, and the spacecraft is heading for a flyby encounter with the Pluto system in the summer of 2015. The challenges associated with sending a spacecraft to Pluto in less than 10 years and performing an ambitious suite of scientific investigations at such large heliocentric distances (>32 AU) are formidable and required the development of lightweight, low power, and highly sensitive instruments. This paper provides an overview of the New Horizons science payload, which is comprised of seven instruments. Alice provides moderate resolution (～3–10 Å FWHM), spatially resolved ultraviolet (～465–1880 Å) spectroscopy, and includes the ability to perform stellar and solar occultation measurements. The Ralph instrument has two components: the Multicolor Visible Imaging Camera (MVIC), which performs panchromatic (400–975 nm) and color imaging in four spectral bands (Blue, Red, CH₄, and NIR) at a moderate spatial resolution of 20 μrad/pixel, and the Linear Etalon Imaging Spectral Array (LEISA), which provides spatially resolved (62 μrad/pixel), near-infrared (1.25–2.5 μm), moderate resolution (λ/δ λ～240–550) spectroscopic mapping capabilities. The Radio Experiment (REX) is a component of the New Horizons telecommunications system that provides both radio (X-band) solar occultation and radiometry capabilities. The Long Range Reconnaissance Imager (LORRI) provides high sensitivity (V<18), high spatial resolution (5 μrad/pixel) panchromatic optical (350–850 nm) imaging capabilities that serve both scientific and optical navigation requirements. The Solar Wind at Pluto (SWAP) instrument measures the density and speed of solar wind particles with a resolution ΔE/E<0.4 for energies between 25 eV and 7.5 keV. The Pluto Energetic Particle Spectrometer Science Investigation (PEPSSI) measures energetic particles (protons and CNO ions) in 12 energy channels spanning 1–1000 keV. Finally, an instrument designed and built by students, the Venetia Burney Student Dust Counter (VB-SDC), uses polarized polyvinylidene fluoride panels to record dust particle impacts during the cruise phases of the mission.     

First measurements of cosmic-ray nuclei at high energy with CREAM

The balloon-borne cosmic-ray experiment CREAM-I (Cosmic-Ray Energetics And Mass) recently completed a successful 42-day flight during the 2004–2005 NASA/NSF/NSBF Antarctic expedition. CREAM-I combines an imaging calorimeter with charge detectors and a precision transition radiation detector (TRD). The TRD component of CREAM-I is targeted at measuring the energy of cosmic-ray particles with charges greater than Z ∼ 3. A central science goal of this effort is the determination of the ratio of secondary to primary nuclei at high energy. This measurement is crucial for the reconstruction of the propagation history of cosmic rays, and consequently for the determination of their source spectra. First scientific results from this instrument are presented.     

Plasma Experiment for Planetary Exploration (PEPE)

The Plasma Experiment for Planetary Exploration (PEPE) flown on Deep Space 1 combines an ion mass spectrometer and an electron spectrometer in a single, low-resource instrument. Among its novel features PEPE incorporates an electrostatically swept field-of-view and a linear electric field time-of-flight mass spectrometer. A significant amount of effort went into developing six novel technologies that helped reduce instrument mass to 5.5 kg and average power to 9.6 W. PEPE’s performance was demonstrated successfully by extensive measurements made in the solar wind and during the DS1 encounter with Comet 19P/Borrelly in September 2001. P. Barker is deceased.     

Sensitivity analyses of satellite propulsion components with their thermal modelling

Performing the sensitivity analyses of the contact conduction and the position of thermostat on the basis of the thermal model established, the study of thermal design is accomplished for the preparation of possible mechanical interface change of the satellite propulsion system depending on the satellite system design. A relatively simple thermal model is taken into consideration for the convenience of the analysis. A variety of the spacecraft bus voltages and the contact resistances are examined as well as the position of thermostat on propulsion components. As a consequence, even though the mechanical interface condition is changed on the same module, the successful thermal design could be achieved if we design the heater to have sufficiently large power with reference to the heritage value of contact resistance. Besides the reasonable performance on the thermal control is assured with the thermostat location errors, if the uncertainty in the position of thermostat is not quite large when assembling tank module.     

Monitoring atomic clocks on board GNSS satellites

A method for monitoring atomic clocks on board Global Navigation Satellites System (GNSS) satellites is described to address the issue of clock related signal integrity in safety–critical applications of GNSS. The carrier-phase time transfer is employed in the clock monitoring method which enables tight tracking of the satellite onboard clocks and thus improves detectability of clock anomalies. Detecting onboard clock anomalies requires the ability to monitor clocks in real time, and a Kalman filter can then be utilized to estimate the phase offsets between the satellite clocks and ground clocks. This study, using the difference between the measured and predicted phase offset as a test statistic, sets a threshold for clock anomalies based on the prediction interval approach. Finally the validity of the monitoring method is examined by processing a set of real GNSS data that includes two recent incidents of clock anomalies in GNSS satellites.     

Development of multi-functional composite structures with embedded electronics for space application

Conventional spacecraft structural function has been limited to supporting loads and mounting avionics only. In contrast, the technology of ‘multi-functional structures’ can integrate thermal and electronic functions into the spacecraft’s inherent load-bearing capability. In addition, sufficient radiation shielding effectiveness can be provided for the anticipated mission environment. Utilizing this concept, the ratio of electrical functionality to spacecraft volume can be dramatically increased and significant mass savings can be obtained. In this paper, spacecraft electronics are miniaturized using advanced IT applications such as flexible circuitry, miniaturized components, featherweight connectors, and so on, that they can be easily embedded within a structural panel. A sandwich structural panel consists of an aluminum honeycomb core and lightweight CFRP facesheets. Integration of electronics is implemented within the panel by mounting electronics on a multi-layered composite enclosure with multi-materials. This composite enclosure provides a load-bearing, effective thermal conduction, radiation shielding capabilities and an available space for embedding electronics. A series of environmental tests and analyses is carried out to demonstrate that the flight hardware is qualified for the expected mission environments. This approach will be utilized for the advanced small satellite ‘STSAT-3’ to validate the multi-functional structures concept.     

Registration of space objects: ESA member states’ practice

The registration of space objects is indispensable for the orderly administration of outer space. Most states recognize this and comply with the instruments—the Registration Convention and the UN General Assembly Resolution—set up to permit registration, but they display different approaches to and interpretations of the concept of registration. This article examines the registration practices of various European Space Agency (ESA) member states and of ESA itself. It finds that, despite varied policies, the system seems to be working well. However, there has been a worrying rise in non-registrations over the past few years, perhaps linked to the growth in the number of, especially commercial, entities engaging in space activities.     

Space activities in Korea—History, current programs and future plans

Korea has participated in space development only since the 1990s. Despite its short history, Korea has been increasing its technological capabilities with the successful experience of several national projects. The Korean government established a long-term space development plan in 1996, which suggests a clear way forward for space development up to 2015. Space activities in Korea will grow continuously. The direction of future space activities will be decided by the national space development plan. This paper discusses Korea's past and present space activities and future development projects.