Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

空间遥操作任务中显控界面关键技术研究进展

为提高空间站机械臂等空间遥操作任务的操作表现,提升操作者的临场感是一项重要的技术途径。为此,须开展显控界面的工效学设计。结合目前国内外研究文献,分别就视觉实景界面,增强现实界面,对抗时延的操作策略,语音、力觉交互以及预警机制等几项关键技术进行了梳理和讨论,并提出了几项空间遥操作人机界面可以深入展开的研究方向。     

Coupling damage and reliability model of low-cycle fatigue and high energy impact based on the local stress–strain approach

Fatigue induced products generally bear fatigue loads accompanied by impact processes,which reduces their reliable life rapidly. This paper introduces a reliability assessment model based on a local stress–strain approach considering both low-cycle fatigue and high energy impact loads.Two coupling relationships between fatigue and impact are given with effects of an impact process on fatigue damage and effects of fatigue damage on impact performance. The analysis of the former modifies the fatigue parameters and the Manson–Coffin equation for fatigue life based on material theories. On the other hand, the latter proposes the coupling variables and the difference of fracture toughness caused by accumulative fatigue damage. To form an overall reliability model including both fatigue failure and impact failure, a competing risk model is developed. A case study of an actuator cylinder is given to validate this method.     

Friction moment analysis of space gyroscope bearing with ribbon cage under ultra-low oscillatory motion

This paper presents the model of calculating the total friction moment of space gyroscope ball bearings which usually work under ultra-low oscillatory motion and are very sensitive to the friction moment. The aim is to know the proportion of the friction moment caused by each frictional source in the bearing＇s total friction moment, which is helpful to optimize the bearing design to deduce the friction moment. In the model, the cage dynamic equations considering six degree-of-freedom and the balls dynamic equations considering two degree-of-freedom were solved.The good trends with different loads between the measured friction moments and computational results prove that the model under constant rate was validated. The computational results show that when the speed was set at 5 r/min, the bearing＇s maximum total friction moment when oscillation occurred was obviously larger than that occurred at a constant rate. At the onset of each oscillatory motion, the proportion of the friction moment caused by cage in the bearing＇s total friction moment was very high, and it increased with the increasing speed. The analyses of different cage thicknesses and different clearances between cage pocket and ball show that smaller thickness and clearance were preferred.     

小型涡扇发动机分布式控制系统总线触发机制研究

为分析比较2种总线触发机制(时间触发和事件触发)对航空发动机实时控制的影响,以某小型涡扇发动机为对象,采用智能节点型分布式结构,构建了其分布式控制系统数字仿真平台;利用True Time/Matlab工具箱展开网络实时仿真研究,系统各节点通过CAN总线进行数据通信。以此仿真平台为基础,对2种触发机制下发动机的转速响应以及对应的时延统计结果表明:在事件触发机制下发动机转速超调量比时间触发机制下的大2.32%;在不同网络负载下,在事件触发机制下的时延大小和尖峰数均大于在时间触发机制下的。最终认为时间触发机制更适合于航空发动机分布式控制系统。     

带迎角钨杆斜侵彻铝板数值仿真研究

为研究迎角对钨杆斜侵过程的影响,开展了带迎角钨杆斜侵彻铝板数值仿真研究。仿真中采用SPH方法,Shock状态方程和Steinberg本构模型。钨杆共有两种尺寸,分别为Φ10mm×23mm和Φ10mm×46mm。铝板厚10mm,撞击速度为2km/s,撞击角度为60°。为简化分析,将迎角分解为俯仰角和偏航角,其中俯仰角范围为-90°～90°,偏航角范围为0°～90°。对钨杆侵彻过程的分析结果表明：斜侵彻存在临界迎角,在临界迎角范围内钨杆所受力矩可忽略不计;在临界迎角范围外,钨杆将发生弯曲甚至折断。对钨杆的剩余质量分析结果表明：当偏航角为0°且钨杆未折断时,剩余质量只在较小的范围内变化;当俯仰角为0°时,剩余质量随迎角增加线性减小。对钨杆的剩余速度分析结果表明：偏航角对剩余速度的影响与俯仰角对剩余速度的影响基本一致,剩余速度曲线关于0°迎角基本对称。根据仿真结果,采用曲线拟合的方法给出了钨杆斜侵彻铝板的剩余速度经验公式。     

置氢TC4钛合金粉末热等静压制件组织与性能研究

采用置氢钛合金粉末热等静压成形与钛合金热氢处理技术相结合的新工艺路线制备合金,研究了置氢量及热等静压工艺参数对置氢TC4合金粉末热等静压制件组织性能的影响规律。结果表明:随着置氢量的增加,置氢TC4合金粉末热等静压后制件的密度呈逐渐增高的趋势;热等静压制件的片层状组织尺寸变薄、针状的组织变细,等轴颗粒组织愈来愈多;退火后制件的显微组织中等轴状的颗粒增多,压缩屈服强度和抗压强度均逐渐增大;热等静压制件与粉末原料的氢含量及相组成基本相近,真空退火除氢后氢含量则达到了安全使用水平,置氢量0.42%TC4合金粉末热等静压制件致密效果好、综合力学性能高。     

激光加工气膜孔对定向凝固高温合金薄壁持久性能的影响

采用定向凝固无余量精铸工艺制造的接近于空心涡轮叶片形状和壁厚的管状薄壁（δ＝１．２ｍｍ）试样,研究了激光加工孔对定向凝固高温合金薄壁持久性能的影响。结果表明,在９００℃／３７０ＭＰａ下,与没有孔的薄壁试样相比,有一排孔的试样持久性能没有明显降低,有两排孔的试样持久寿命略有下降。显微分析表明,激光加工孔对组织没有明显的影响,只是稍微减小了承载面积,而且只有在出现两排激光孔时才有所表现。     

基于阻塞流的机场终端区极限容量评估研究

为确定机场终端区最大容量保障能力,即极限容量,从终端区运行特点分析出发,综合考虑进离场航线长度、飞行速度、管制间隔等因素,构建进离场网络流模型,并以跑道Pareto容量包络线作为约束,分析进离场航线网络与跑道的耦合关系,建立基于阻塞流的机场终端区极限容量评估模型。以杭州萧山机场终端区为例,验证了模型的可行性和准确性,并借助模型分析了不同流量控制策略下终端区容量包络线的变化趋势。研究表明,随着移交间隔变大,终端区容量包线有内移的趋势,进场容量由33架次/h逐步降为25架次/h。