全文获取类型
收费全文 | 397篇 |
免费 | 102篇 |
国内免费 | 57篇 |
专业分类
航空 | 370篇 |
航天技术 | 51篇 |
综合类 | 43篇 |
航天 | 92篇 |
出版年
2024年 | 1篇 |
2023年 | 7篇 |
2022年 | 34篇 |
2021年 | 27篇 |
2020年 | 16篇 |
2019年 | 13篇 |
2018年 | 23篇 |
2017年 | 35篇 |
2016年 | 19篇 |
2015年 | 21篇 |
2014年 | 24篇 |
2013年 | 23篇 |
2012年 | 21篇 |
2011年 | 35篇 |
2010年 | 37篇 |
2009年 | 27篇 |
2008年 | 18篇 |
2007年 | 27篇 |
2006年 | 24篇 |
2005年 | 37篇 |
2004年 | 26篇 |
2003年 | 20篇 |
2002年 | 14篇 |
2001年 | 10篇 |
2000年 | 10篇 |
1999年 | 7篇 |
排序方式: 共有556条查询结果,搜索用时 15 毫秒
41.
Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height. 相似文献
42.
43.
利用PIV技术对两种不同尺寸的中心突扩燃烧室在不同入口速度条件下的冷态流场进行了实验研究,测量并分析了流场结构与来流速度、突扩比、喷管收缩段等因素的关系。实验结果表明利用PIV技术能较好地获得高速条件下燃烧室二维速度场;对于不同突扩比的燃烧室,突扩面后的流场结构类似,但回流区的最大负速度与入口速度的比例关系不同;在喷管人口处,流场在此处重新形成旋涡,其直径较大,但强度相对较弱。 相似文献
44.
45.
46.
47.
旋转状态下气膜冷却效率试验研究 总被引:1,自引:0,他引:1
以某型发动机高压涡轮转子叶片吸力面腮区气膜孔为研究对象,通过模拟发动机状态的模型试验,研究了旋转数、吹风比和主流雷诺数对气膜孔冷却效率的影响。结果表明,旋转会导致气膜覆盖区域向高半径方向偏转,且旋转数越大,偏转角度越大,气膜冷却效率越低;同时,旋转会弱化吹风比、主流雷诺数等对气膜冷气效率的影响。研究获得的旋转状态下涡轮转子叶片型面典型区域气膜冷却特性的试验数据,可为发动机转子叶片冷却设计提供参考。 相似文献
48.
49.
DZ125定向凝固高温合金长期时效后的显微组织和超高周疲劳行为 总被引:1,自引:0,他引:1
选用950 ℃时效温度,对DZ125定向凝固高温合金进行了500、1 000、1 500 h的长期时效。利用超声疲劳试验机测试了合金的超高周疲劳性能。采用扫描电子显微镜、透射电子显微镜和电子背散射衍射(EBSD)研究了合金的显微组织和超高周疲劳行为。结果表明:长期时效对DZ125合金的组织稍有影响,长期时效后合金的点阵错配度降低,随着时效时间的延长,γ'相聚集长大更加明显,未出现拓扑密排相(TCP)等有害相;长期时效对DZ125合金的超高周疲劳性能稍有影响,随着时效时间的延长,疲劳性能呈下降趋势,疲劳断口较平整,裂纹起源于试样的表面,在超高周疲劳后合金的晶粒发生了小幅度旋转。 相似文献
50.