全站仪检测数据管理系统

介绍了全站仪检测数据管理系统。本系统以FoxPro for Windows为基础,采用模块结构,具有对检测数据录入修改,自动转换,成果计算,查询显示等功能,实现了系统数据管理和处理的一体化。     

组合机床多轴箱计算机辅助设计系统

介绍利用ＡｏｔｏＣＡＤ二次开发工具ＯｂｊｅｃｔＡＲＸ３．０开发的组合机床多轴箱ＣＡＤ。阐述依据模块化原理设计系统的各个组成模块,以及由于采用ＶｉｓｕａｌＣ＋＋６．０可视化编程语言及微软ＭＦＣ基本类库,使程序界面的交互性比以往设计显著提高。     

多向编织C/ C 复合材料显微结构的滋-CT 研究

以多向编织C/C复合材料为研究对象,对其内部组织结构进行了CT扫描,通过对投影旋转中心校正、噪声抑制、环状伪影校正等数据进行了处理.结果表明:经过处理数据,图像质量明显改善,提高了材料内部微结构细节的辨识程度,为C/C复合材料内部微结构三维重构提供了良好的基础.     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

涡轮气冷动叶片伸根段参数化设计方法研究

提出了叶片伸根段控制截面线生成方法.将伸根段设计分为内型和外型两部分,通过直纹面插值法获取伸根内型截面线,再通过变壁厚法获取伸根外型截面线,详细分析了其中的关键技术和算法;提取了伸根设计参数,开发了伸根设计专用模块,实践证明,应用本模块进行伸根设计,可以极大提高伸根乃至整个叶片设计效率.     

一种可紫外光固化新型耐烧蚀涂料研究

基于巯基-乙烯基光引发逐步聚合机理,以含有乙烯基的液态硅氮烷预聚物与多元巯基化舍物为基体,辅以某种陶瓷微粉作为填料,研制了一种可紫外光固化的新型耐烧蚀涂料.采用等温差示光量热扫描(DPC)和测试固化度研究了填料添加量对紫外光固化放热行为和一次成型厚度的影响关系.结果表明:在制备0.5 mm厚的涂层时,填料添加量逐渐从0增至5%(质量分数,下同),固化放热峰值和放热量随添加量的增大而逐渐减小,且固化放热峰从尖锐逐渐趋于平坦,这是由于填料的加入使得涂料变为不透明,对入射的紫外光线产生了衍射/反射作用,从而减弱了辐照强度;填料添加量大于10%时,明显阻碍光固化反应的发生,涂层的一次成型厚度随填料添加量的增加而降低,可采用多次涂敷的措施解决涂层厚度不足的问题.当填料添加量从0增至20%,对于1.0 mm厚的涂层而言,在800℃质量保持率从61.2%增至73.5%.填料含量20%的涂层具有较为优异的耐烧蚀性能,氧-乙炔烧蚀的线烧蚀率为0.252 inm/s,质量烧蚀率为61.7 mg/s.     

氙离子推力器束流分布特性研究

建立了离子推力器束流分布的高斯模型,以200mm氙离子推力器为例,在不同工作环境下对推力器束流分布进行了数值模拟,并通过试验测量了推力器引出切面不同位置(轴向z=50mm,z=100mm)下的径向束电流密度和束离子密度分布。通过对数值模拟结果与试验测量结果的比较,误差为17%,认为数值模拟结果与试验测量结果吻合较好。表明离子推力器引出束流呈轴对称分布,在推力器出口附近,束离子密度很大,越往下游,密度越小且束流出现发散。     

柔性机械臂关节作动的振动抑制方法和原理性验证

空间机械臂具有柔性大、振动频率低等特点,受激后振动的持续时间长、自然衰减慢。针对空间机械臂运行完成后留存的残余振动,采用固定界面子结构方法推导出关节转动与航天器-机械臂组合体振动的动力学显式关系。从中发现了控制关节转动并使其角速度正比于组合体振动的模态坐标,便能消耗组合体的机械能,加速组合体振动衰减的力学机理。据此,设计了逻辑关系简洁的机械臂关节角速度控制律,分别通过数值仿真和试验件实测对航天器-机械臂组合体的原理性模型开展了振动抑制效果的验证。结果表明:机械臂关节作动可以显著缩短受激后组合体残余振动的持续时间。     

天问一号探测器高动态着陆惯导系统设计与试验

考虑到火星探测任务着陆过程动态变化大,稀薄大气环境下开伞会对探测器产生剧烈晃动,为此天问一号探测器研制了一套高动态着陆惯导系统,从硬件产品、使用时序到导航算法方面均进行了针对性设计,以适应着陆过程中的高动态环境.此外,为验证天问一号探测器高动态着陆惯导系统的性能,设计了模拟火星开伞工况的火箭弹高空开伞试验,结果表明该高...     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.