气动发动机输出扭矩无因次分析

针对气动发动机的工作过程,利用能量方程、气体状态方程、连续性方程及运动过程方程建立气动发动机的非线性微分方程组.选取合适的基准量,对所建立的微分方程组进行无因次化,得到无因次化的数学模型.利用MATLAB/Simulink仿真工具,对无因次数学模型进行研究,得到各无因次量对气动发动机输出扭矩的影响.从仿真结果可以看出,气动发动机的无因次转速、进气门面积比例因子、排气门面积比例因子以及进气持续角度对气动发动机的无因次输出扭矩影响较大.当发动机转速升高扭矩急剧下降时,可以通过调整进气门面积比例因子、排气门面积比例因子以及进气持续角度使输出扭矩恒定.     

对接口匹配的航天器双主动最优交会研究

研究了两航天器协同轨道机动（双主动）完成近距离交会任务的最优控制问题。在考虑航天器姿态变化、对接口位置及路径约束的情况下,构建了完整的6自由度、26状态的双主动最优交会数学模型。利用高斯伪谱法分别将燃料总消耗最少和交会时间最短两种最优问题离散为大型非线性规划问题,而后应用SNOPT软件包进行了求解。在此基础上通过大量数值计算分析总结了不同初始参数对最小燃料消耗和最短交会时间的影响规律,并与主被动交会形式进行了对比。结果表明,当两航天器质量接近时,双主动交会通常可明显减少燃料消耗,或缩短交会时间;而当质量差距较大时,双主动最优交会逐渐退化为主被动最优交会。     

Response of Hainan GPS ionospheric scintillations to the different strong magnetic storm conditions

Using the GPS ionospheric scintillation data at Hainan station (19.5°N, 109.1°E) in the eastern Asia equatorial regions and relevant ionospheric and geomagnetic data from July 2003 to June 2005, we investigate the response of L-band ionospheric scintillation activity over this region to different strong magnetic storm conditions (Dst < −100 nT) during the descending phase of the solar cycle. These strong storms and corresponding scintillations mainly took place in winter and summer seasons. When the main phase developed rapidly and reached the maximum near 20–21 LT (LT = UT + 8) after sunset, scintillations might occur in the following recovery phase. When the main phase maximum occurred shortly after midnight near 01–02 LT, following the strong scintillations in the pre-midnight main phase, scintillations might also occur in the post-midnight recovery phase. When the main phase maximum took place after 03 LT to the early morning hours no any scintillation could be observed in the latter of the night. Moreover, when the main phase maximum occurred during the daytime hours, scintillations could also hardly be observed in the following nighttime recovery phase, which might last until the end of recovery phase. Occasionally, scintillations also took place in the initial phase of the storm. During those scintillations associated with the nighttime magnetic storms, the height of F layer base (h’F) was evidently increased. However, the increase of F layer base height does not always cause the occurrence of scintillations, which indicates the complex interaction of various disturbance processes in ionosphere and thermosphere systems during the storms.     

一类准循环LDPC码及其编码

针对空间通信的特点, 对基于循环矩阵构造的一类正则准循环LDPC码进行了改进, 得到了一类非正则准循环LDPC码. 与原码相比, 这类非正则LDPC码的奇偶校验矩阵H具有3个特点: 行满秩, 具有下三角结构, 引入了一度变量节点. 前两个特性使得这种LDPC码的编码计算复杂度和结构复杂度都与校验位长度成正比, 从而便于编码器的软硬件实现. 第三个特性使码的迭代译码门限稍有降低, 但同时还能保证译码的收敛, 计算机仿真结果也证明了这一点. 本文还简化了对围长不小于6的条件的证明, 推导了系统码校验位的计算公式, 并在此基础上给出了利用移位寄存器的编码电路.      

基于深度学习的毫米波和亚毫米波成像仪的图像增强技术

风云四号卫星毫米波和亚毫米波成像仪(MMSI)数据根据采样方式分为过采样和非过采样数据。由于采样方式的影响,非过采样数据在采样过程中会有一定的信息损失。为解决采用简单的线性插值方法做精细化处理时提升精度有限问题,采用基于深度学习的方法增强MMSI亮温图像,设计卷积神经网络重建风云四号卫星MMSI的亮温图像和风云三号卫星微波成像仪亮温图像。实验结果显示:相比传统的双三次插值方法,在风云三号卫星微波成像仪亮温图像样本上峰值信噪比提升了1.13dB,结构相似度提升了0.01。实验结果表明:对于非过采样亮温数据,采用基于深度学习的方法增强图像具有更高的精度,同时可在其他微波探测仪数据中使用,具有很强的普适性。     

数控五坐标高速铣床的PLC控制

介绍了一种高速铣床CNC控制系统的结构及特点:指出了这台铣床PLC程序设计中的重点问题,为此类高速数控机床的控制提供了技术参考.     

亚超剪切混合层燃油雾化特性试验研究

为了摸清亚超大梯度剪切混合层内直射式喷嘴的燃油雾化特性,设计了用于向亚超剪切混合流中进行燃油喷射的直射式喷嘴,建立了亚超剪切混合层中燃油雾化试验系统。利用粒子图像测速系统（PIV）,对亚超大梯度混合层中油雾场进行测量。通过改变喷嘴流量、喷射角度和喷嘴数量研究不同参数对雾化特性的影响,并应用图像处理技术对亚超大梯度剪切混合层内的油雾场进行分析,总结归纳其雾化规律。试验结果显示：随着流量增大,穿透深度会随之增大,破碎后的颗粒分布峰值所对应的液滴直径会逐渐变小,雾化效果提升;相同流量条件下,喷嘴的角度改变对雾化效果有影响,顺喷和逆喷的雾化效果均好于垂直喷射;逆喷的喷射高度最高,随着流量的增长,燃料将会碰壁;顺喷条件下,随着角度的增加,穿透长度会有所增加;综合燃油轨迹边界,逆喷的效果相对较好。相同流量条件下,喷孔个数的改变对雾化效果和穿透深度的影响不大。     

航天光学相机地面测控设备通用化研究

文章提出了航天光学相机控制系统测试设备通用化研究的思路，制定了通用化方案，对各功能模块进行了通用化设计。     

WAKE GEOMETRY CALCULATIONS FOR TILT-ROTOR USING VISCOUS VORTEX METHOD

A tilt-rotor unsteady flow analytical method has been developed based upon viscous vortex-particle meth- od. In this method, the vorticity field is divided into small assembled vortex particles. Vortex motion and diffusion are obtained by solving the velocity-vorticity-formed incompressible Navier-Stokes equations using a grid-free La- grangian simulation method. Generation of the newly vortex particles is calculated by using the Weissinger-L lifting surface model. Furthermore, in order to significantly improve computational efficiency, a fast multiple method （FMM） is introduced into the calculation of induced velocity and its gradient. Finally, the joint vertical experimen- tal （JVX） tilt-rotor is taken as numerical examples to analyze. The wake geometry and downwash are investigated for both hover and airplane modes. The proposed method for tilt-rotor flow analysis is verified by comparing its re- sults with those available measured data. Comparison indicates that the current method can accurately capture the complicated tilt-rotor wake variation and be suitable for aerodynamic interaction simulation in complex environ- ments. Additionally, the aerodynamic interactional characteristics of dual-rotor wake are discussed in different ro- tor distance. Results show that there are significant differences on interactional characteristics between hover mode and airplane mode.     

海上小井眼脉冲空化射流发生器射流特性室内试验研究

为了经济地开发海上边际油气资源,将小井眼单通道井井身结构及水力脉冲空化射流提速技术相结合研制出了小尺寸(外径为120mm)水力脉冲空化射流发生器,并采用室内试验研究了其射流特性。分析了其在不同排量下的出口压力脉动频率、入出口压力脉动振幅、工具压耗等参数和自激振荡喷嘴的射流特性。研究表明,出口压力脉动频率与排量呈线性增大关系,入口及出口压力脉动振幅随排量增大而呈增大趋势,工具压耗与排量呈2次增大关系,自激振荡喷嘴能够产生负压和空化效应。