GRACE gravity field modeling with an investigation on correlation between nuisance parameters and gravity field coefficients

The GRACE (Gravity Recovery And Climate Experiment) monthly gravity models have been independently produced and published by several research institutions, such as Center for Space Research (CSR), GeoForschungsZentrum (GFZ), Jet Propulsion Laboratory (JPL), Centre National d’Etudes Spatiales (CNES) and Delft Institute of Earth Observation and Space Systems (DEOS). According to their processing standards, above institutions use the traditional variational approach except that the DEOS exploits the acceleration approach. The background force models employed are rather similar. The produced gravity field models generally agree with one another in the spatial pattern. However, there are some discrepancies in the gravity signal amplitude between solutions produced by different institutions. In particular, 10%–30% signal amplitude differences in some river basins can be observed. In this paper, we implemented a variant of the traditional variational approach and computed two sets of monthly gravity field solutions using the data from January 2005 to December 2006. The input data are K-band range-rates (KBRR) and kinematic orbits of GRACE satellites. The main difference in the production of our two types of models is how to deal with nuisance parameters. This type of parameters is necessary to absorb low-frequency errors in the data, which are mainly the aliasing and instrument errors. One way is to remove the nuisance parameters before estimating the geopotential coefficients, called NPARB approach in the paper. The other way is to estimate the nuisance parameters and geopotential coefficients simultaneously, called NPESS approach. These two types of solutions mainly differ in geopotential coefficients from degree 2 to 5. This can be explained by the fact that the nuisance parameters and the gravity field coefficients are highly correlated, particularly at low degrees. We compare these solutions with the official and published ones by means of spectral analysis. It is found that our solutions are, in general, consistent with others in the spatial pattern. The water storage variations of the Amazon, Chari and Ganges river basins have also been computed. The variations computed with the NPARB approach are closer to those produced by JPL and DEOS solutions, while the variations produced with the NPESS approach are in good agreement with those produced by the CSR and GFZ solutions. A simulation study is implemented with considering realistic noise and low-frequency error. The two approaches are used to recover the true model. The NPESS solution appears closer to the true one. Therefore we are inclined to estimate the nuisance parameters simultaneously with the geopential coefficients.     

干涉配合构件的应力腐蚀开裂特性

采用恒载荷拉伸实验技术,研究了镀锌３０ＧｒＭｎＳｉＡ锡螺栓干涉配合连接ＬＹ１２－ＣＺ铝合金构件在３．５％ＮａＣａｌ＋０．５％Ｈ２Ｏ２溶液中的应力腐蚀开裂特性。结果表明,随干涉量的增加,应力腐蚀敏感性有所下降,基材与紧固件的电偶效应对应力腐蚀繁感性有重大影响。     

PIP工艺制备SiC晶须增强SiCf/SiC复合材料的性能

以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiC_f(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiC_f/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m^1/2;在SiC_f/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。     

热压工艺在Cf／SiC复合材料制备中的应用

探讨了热压工艺 (HP)在常压浸渍裂解 (PIP)制备 Cf/Si C复合材料制备过程中的应用 ,认为热压浸渍裂解工艺 (HP-PIP)既可以改善碳纤维与基体 Si C之间的界面 ,又可以提高材料的致密度 ,使材料内部的空隙减少或消失 ,同时使孔隙排布均匀 ,从而使材料的性能有了大幅度提高 ,其强度由原来的 2 90 MPa提高到 5 40 MPa,并且可重复性很好     

某型涡轮轴发动机稳态气路故障诊断方法

本文是涡轮轴发动机稳态气路故障诊断方法研究的结果。根据监控功能要求 ,应用气路参数分析法 ,确定反映部件性能参数变化的测量参数 ,建立故障诊断模型 ,探讨分别应用 6个和 4个测量参数诊断气路部件故障的方法     

刷式密封接触动力学特性研究

对刷式密封的结构动力学特性进行了分析,从弹性理论出发,考虑轴颈和密封环之间的非线性摩擦力作用,建立了密封环与转子相互作用的非线性动力学方程,推出了密封环对转子的非线性支承刚度的近似表达式,这一支承刚度的导出为研究转子—密封—轴承系统的非线性动力学行为奠定了基础。最后用数值仿真方法验证了本文推导出的表达式的正确性。     

Parylene真空涂覆新工艺研究

简述了Parylene真空沉积的机理,并对采用Parylene真空涂覆的涂层样件进行了全面的性能摸底试验。     

失速起始检测的低频平均频谱幅值法

高速多级轴流式压气机在中低转速的失速起始总是以短周期扰动的形式出现。为了在压气机整机进入深度失速前检测到失速起始信号，通过分析提出了一种基于低频平均频谱幅值的失速起始信号检测方法。对某轴流式压气机压力测量信号的分析结果表明，该方法是准确、可靠和快速的，有望用于失速起始的实时检测。     

高过载条件下绝热层烧蚀实验方法研究 (Ⅰ)方案论证及数值模拟

分析了高过载对固体火箭发动机流场和绝热层烧蚀的影响规律，提出一种新的研究思路：采用数值模拟方法来预示发动机三维两相流场，建立高过载流场模拟实验装置，开展绝热层烧蚀实验，建立高过载条件下的绝热层烧蚀模型，在此基础上发展高过载发动机绝热层设计和烧蚀预示方法。其中关键技术是高过载流场的模拟，对粒子加入法和弯管分离法两种方案进行了论证，认为弯管分离法原理上是可行的。为了验证这种方案的可行性，开展了弯管通道两相流的数值模拟研究，计算结果表明弯管装置具有使凝相粒子聚集形成高浓度粒子流的功能。