HP8350B扫频仪射频插件单元故障修理三例

针对HP8350B系列微波扫频仪射频插件单元的三例典型故障。介绍了其修理方法，同时就该类微波测量仪器在修理过程中应该注意的几个问题阐述了作者的意见。     

A 16-moment Fast Solar Wind Model

A 16-moment fast solar wind model based on a bi-Maxwellian velocity distribution is presented. Although the proton heat flux density is found to be significantly smaller than the classical Spitzer-Härm value, it still plays a significant role in shaping the proton temperature anisotropy in the fast solar wind.     

冷轧变形对Inconel 718合金δ相γ″相析出行为的影响

采用Ｘ射线衍射技术测定了冷轧Ｉｎｃｏｎｅｌ７１８合金在８６０℃加热温度下的δ相和γ″相含量，研究了冷轧变形对δ相和γ″相析出行为的影响。结果表明，冷轧变形影响δ相的析出形貌，随冷轧变形量增加，δ相由针状向颗粒状转变。δ相析出的重量百分数与时间的关系符合Ａｖｒａｍｉ方程，随冷轧变形量增加，ｎ值减小，α值增加。在８６０℃加热温度下，等温１５ｍｉｎ时已有γ″相析出，随时间增加，γ″相含量增加，达到最大值后又降低。在试验中给定的时间条件下，随冷轧变形量增加，γ″相含量降低，而δ相含量增加。     

关于构建教材成果评价体系的探讨

教材建设是高校学科建设的重要内容 ,也是教师学术成果的表现形式之一。教材水平直接影响教学质量。建立一种尽可能客观公正的教材成果评价体系 ,这对鼓励编写和使用优秀教材 ,客观评价教师科研教学成果 ,遏止学术不正之风 ,规范学术活动 ,促进教学和科研工作的健康发展 ,推动教材建设和教学质量的提高具有积极意义     

悬链面上的非线性控制系统

讨论了悬链面上的非线性控制系统的表示及性质     

基于直升机飞行性能需求的涡轴发动机设计参数选取方法研究

以直升机性能计算方法为基础,辅以考虑尺寸效应及设计能力的涡轴发动机设计方法,建立了以直升机旋翼桨盘载荷及最大起飞功重比为特征参数的直升机/涡轴发动机性能约束分析模型、任务分析模型及基于直升机飞行性能需求的涡轴发动机设计参数选取模型。针对涡轴发动机部件/系统设计能力及直升机飞行性能需求,首先开展了给定涡轴发动机循环参数下的流量匹配计算,然后开展了涡轴发动机循环参数选取研究。研究表明,所建立的直升机/涡轴发动机性能约束分析模型、任务分析模型可实现给定飞行任务的直升机/涡轴发动机性能耦合设计;在给定涡轴发动机循环参数条件,由于尺寸效应,涡轴发动机部件效率受进口流量的影响,其设计点功率并不随流量等比例变化,从而使得直升机起飞总重呈现非等比例变化;在涡轴发动机循环参数选择时,在满足直升机飞行性能需求下,存在涡轴发动机耗油率与单位功率之间权衡下的循环参数选取,使得直升机起飞总重最小。     

从双层到多层带有微结构的硅硅直接键合技术研究

通过理论分析和实验验证对多层带有微结构的硅硅直接键合技术进行了研究.采用的硅片表面活化处理方法是亲水湿法,采用的键合工艺流程是先将硅片在键合机中进行预键合,再使用退火炉进行高温退火.其中预键合参数对多层键合成功与否起到决定性的作用,为节约实验时间,针对3个主要预键合参数（温度、压力、时间）的选取进行了详细的正交实验分析.使用项目组自制的硅硅键合分析软件对键合片的红外图像进行处理分析,计算键合率.采用实验得到的最佳预键合工艺参数,多层键合的键合率达到了86.6527%.      

A New Exposed-terminal-free MAC Protocol for Multi-hop Wireless Networks

This article presents a new multichannel medium access control (MAC) protocol to solve the exposed-terminal (ET) problem for efficient channel sharing in multi-hop wireless networks. It uses request-to-send and clear-to-send (RTS/CTS) dialogue on a common channel and flexibly opts for conflict-free traffic channels to carry out the data packet transmission on the basis of a new channel selection scheme. The acknowledgment (ACK) packet for the data packet transmission is sent back to the sender over another common channel thus completely eliminating the exposed-terminal effects. Any adjacent communication pair can take full advantage of multiple traffic channels without collision and the spatial reuse of the same channel is extended to other communication pairs which are even within 2 hops from them. In addition, the hidden-terminal effect is also considerably reduced because most of possible packet collisions on a single channel are avoided due to traffic load balance on multichannels. Finally, a performance comparison is made between the proposed protocol and other typical MAC protocols. Simulation results evidence its obvious superiority to the MAC protocols associated with other channel selection schemes and traditional ACK transmission scheme as well as cooperative asynchronous multichannel MAC (CAM-MAC) protocol in terms of four performance indices: total channel utilization, average channel utilization, average packet delay, and packet dropping rate.     

基于结构随机跳变系统的制导交班边界设计

为了减小最终脱靶量,研究了系统存在随机扰动时交班切换边界定位问题。首先建立了具有中制导和末制导的结构随机跳变系统模型,然后根据结构随机跳变系统理论进行系统概率分析,并在此基础上结合优化算法,得到最优的交班切换边界,使得当前脱靶量的数学期望和方差最小。最后,进行了某型导弹纵向俯仰通道仿真,验证了该方法的有效性。     

Dynamics and autopilot design for endoatmospheric interceptors with dual control systems

The nonlinear system model of an endoatmospheric missile whose attitude is controlled by tail fins and reaction jets is presented. By choosing the divert accelerations and rotational rates as output variables, the internal dynamics of the nonlinear system are derived and are proved to be bounded under a bounded input. The blending principle of the reaction jets and tail fins is addressed to ensure that the normal acceleration is principally maintained by angle-of-attack or sideslip angle. An autopilot is designed by using the feedback linearization technique. Results of a numerical simulation of an autopilot design example show the effectiveness of the proposed blending principle and the autopilot design.