亚、超音速机翼非定常广义气动力系数之间的关系

 <正> 研究弹性飞机的动力学特性应计及非定常广义气动力。为了尽可能保留非定常运动历程,应首先计算由阶跃函数形式下洗产生的非定常气动力函数(指示函数或指数函数),再利用卷积形式的迭加原理处理任意函数形式下洗产生的非定常气动力。用振型法建立飞机弹性运动方程,可将飞机上任一质点的弹性位移近似地表示为     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.     

高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

基于人工神经网络的停机坪安全预警研究

停机坪是机场的重要组成部分,停机坪安全是机场安全关注的重点。影响停机坪安全作业的要素有很多,通过对这些要素进行监控和预警,可以减少停机坪的安全隐患,保证机场正常运行。根据济南遥墙机场的主要数据,运用因子分析法对影响停机坪安全的主要因素进行分类,提取公共因子。并运用人工神经网络（ANN）方法,对这些公共因子进行神经网络训练和预测分析,最终得到遥墙机场停机坪的安全情况。     

基于非线性变换的加速度计误差标定与补偿CSCD

为提高三轴加速度计测量精度,分析其误差来源和产生机理,建立了误差模型;根据误差模型和重力场幅值不变特性,推导出非线性观测方程。引入两个未知的参数向量,通过数学变换把非线性观测方程变形为关于新未知参数的线性方程;然后采用批量最小二乘法求出新的未知参数,并根据误差模型参数和新未知参数之间的关系,利用逆解析运算求出对应的零点偏差、灵敏度误差和三轴不正交误差。实验结果表明,加速度计正负误差峰值间距可以减小100倍左右,精度可达10-3m/s2,并具有很好的可重复性。该方法算法效率较高,补偿效果显著。     

卷簧式浅层月壤取样器设计及动力学分析

面向浅层月壤取样,文章设计了新颖的卷簧式可伸缩小型月壤取样器,它包括柔性取样臂和振动式取样头。对取样器进行了动力学有限元分析,研究了取样臂为不同长度时取样头的振动模态及频率响应,得出取样臂一阶横振频率与取样臂长度呈负幂函数关系;对取样器测控系统进行了振动试验,通过扫频方式测量取样臂为不同长度时的自振频率,给出了取样臂长...     

供热系统集约化运行的能耗监测及节能调节问题探讨

对我校供热系统的现状进行了分析；指出了锅炉热效率及能耗监控方面的不足，并针对锅炉热效率提高和二次网循环泵变频调节进行了节能分析计算；同时根据我校实际情况对循环泵设备配置及控制进行了分析，提出了要加强技术指标量化考核和能耗监测，提高效率、节能降耗，实现供热系统的科学化、集约化运行。     

压气机叶片型面精密数控铣加工技术应用研究

为了提高压气机叶片型面和进、排气边转接圆角的数控铣加工质量,在工艺、夹具、数控加工模型与程序以及检测方法等方面采取了攻关措施,减小了叶片型面精铣加工的变形,实现了叶身型面的精密铣削加工,对型面采用毡轮修光去除铣削痕迹后,经过3坐标、小半径投影仪等设备的测量,进、排气边转接圆角的形状和型面轮廓度、位置度各项要求的加工质量得到了质的提升,其合格率由20％提高到75％以上,加工效率和刀具耐用度提高1倍以上,使叶身型面精密铣削技术具备了精品叶片批量生产的工程化应用技术基础.     

基于改进WKNN的位置指纹室内定位算法

位置指纹算法是目前解决室内定位问题的主要方法,指纹特征和匹配算法为影响算法精度的两大因素.针对室内复杂环境下Wi-Fi信号强度波动较大的现象,提出了基于方差的加权距离以改进WKNN算法.在离线特征提取阶段,选择了均值和方差两个特征值,既反映该采样点的RSS幅值,也反映该点RSS的波动情况;在线阶段,根据方差提出了加权距离进行相似度的计算,查找距离最近的K近邻点,并以实际环境下采集的数据验证了改进WKNN算法在RSS波动大的情况下对定位效果的改善,在综合考虑了AP组合的影响后,实现了误差均值为1.456m的定位效果.