垂直度误差对复合材料单钉连接性能的影响

为揭示连接孔垂直度误差对航空复合材料连接性能的影响规律,对准各向同性碳纤维环氧树脂复合材料板进行了单钉单剪试验研究。以极限承载强度、弦刚度、2%偏移承载强度为指标研究连接孔的倾斜角度、倾斜方向以及螺栓扭矩对接头承载性能的影响规律。试验结果表明:当连接孔倾斜角度从0°增加到4°时,接头弦刚度增大10%~40%,极限承载强度下降9%~12%;连接孔倾斜方向对极限承载强度影响甚微,却可使接头弦刚度产生20%~30%的变化;增加螺栓扭矩可以有效提高极限承载强度,但对接头刚度无明显影响;连接孔倾斜角度越大,则螺栓扭矩的增大对2%偏移承载强度的强化效果越不明显。     

热处理真空淬火工艺的应用

超高强度钢在普通空气炉和盐炉中热处理后，零件表面氧化脱碳相对比较厚，再返回机加车间精加工，其高强度给机加带来不便。通过改进热处理工艺，采用保护气氛炉或真空炉淬火，在满足机械性能要求的前提下，实现少、无氧化热处理。     

Accuracy analysis of GNSS-IR snow depth inversion algorithms

In recent years, with the continuous development of Global Navigation Satellite System (GNSS), it has been applied not only to navigation and positioning, but also to Earth surface environment monitoring. At present, when performing GNSS-IR (GNSS Interferometric Reflectometry) snow depth inversion, Lomb-Scargle Periodogram (LSP) spectrum analysis is mainly used to calculate the vertical height from the antenna phase center to the reflection surface. However, it has the problem of low identification of power spectrum analysis, which may lead to frequency leakage. Therefore, Fast Fourier Transform (FFT) spectrum analysis and Nonlinear Least Square Fitting (NLSF) are introduced to calculate the vertical height in this paper. The GNSS-IR snow depth inversion experiment is carried out by using the observation data of P351 station in PBO (Plate Boundary Observatory) network of the United States from 2013 to 2016. Three algorithms are used to invert the snow depth and compared with the actual snow depth provided by the station 490 in the SNOTEL network. The observations data of L1 and L2 bands are respectively used to find the optimal combination between different algorithms further to improve the accuracy of GNSS-IR snow depth inversion. For L1 band, different snow depths correspond to different optimal algorithms. When the snow depth is less than 0.8 m, the inversion accuracy of NLSF algorithm is the highest. When the snow depth is greater than 0.8 m, the inversion accuracy of FFT algorithm is higher. Therefore, according to the different snow depth, a combined algorithm of NLSF + FFT is proposed for GNSS-IR snow depth inversion. Compared with the traditional LSP algorithm, the inversion accuracy of the combined algorithm is improved by 10%. For L2 band data, the results show that the accuracy of snow depth inversion of various algorithms do not change with the variations of snow depth. Among the three single algorithms, the inversion accuracy of FFT algorithm is better than that of LSP and NLSF algorithms.     

风扇出口导向叶片低噪声设计Ⅰ:方法与优化

作为"风扇出口导向叶片（Outlet Guide Vanes，OGV）低噪声设计"系列文章的第1篇，本文在现有压气机气动设计流程的基础上，加入了噪声评估过程，建立了基于通流设计的气动/声学一体化设计方法。为提高设计阶段的评估速度，以三维升力面理论与管道声学理论为基础，从通流设计和造型设计输出中提取参数，结合转子尾迹模型，建立了转/静干涉噪声的解析预测模型。以现代大涵道比涡扇发动机风扇/增压级为对象，采用该模型系统分析了OGV轴向掠形与周向倾斜对转/静干涉噪声的影响，获取了轴向掠形角与周向倾斜角等三维设计参数与风扇噪声的关系图谱，初步确定了低噪声设计较优降噪量的掠和倾组合方案。以此为基础，在保持叶尖子午投影位置和弦长不变的前提下，将叶片前缘和径向积叠进行参数化，采用遗传算法进一步开展了OGV的低噪声优化设计，最终获得了2个优化方案，预估的降噪量达到了8 dB。     

基于工作过程的高职教学模式改革初探——浅议广州民航职业技术学院飞机电子系统课程教改

针对我国的飞机维修行业人才培养存在的问题,以广州民航职业技术学院＂飞机电子系统＂课程为例,通过分析＂飞机电子系统＂课程特点与原教学模式存在的问题,根据专业岗位要求,重新构建课程载体、教学手段与成绩处理,探讨基于工作过程的高职教学模式的改革实践。     

基于积分投影的去除噪声算法用于人脸图像处理

本文提出了一种解决滤除人脸图像中高频及低频噪声的新算法。首先可对原始人脸图像进行边界提取，并使之成为二值图；然后，分别采用水平及垂直积分投影的方法，在低频与高频噪声中确定人脸轮廓；在此基础上，消除轮廓以外的噪声。     

Kalman filtering for GPS/magnetometer integrated navigation system

This paper investigated the data processing method for a GPS/IMU/magnetometer integrated system with Kalman filtering (KF). As a result of GPS/IMU/magnetometer land vehicle system, dead-reckoning of magnetometer and accelerometer integrated subsystem bridged very well the GPS signal outage due to the trees on the two sides of the road. Both differential GPS data processing method and the carrier-phase method with magnetometers’ outputs for predicting the car position, velocity, and acceleration (PVA) are presented. The results from DGPS with Kinematical Positioning (KINPOS) software shown that the averages of the north, east, and down direction standard deviation (short for “std”) are 0.014, 0.010, and 0.018 m, respectively. The std of velocities and accelerations derived by the position and velocity differentiation are 10, 7, 13 mm/s, 7, 5, 9 mm/s², respectively. This method for getting velocities and accelerations requires higher accurate position coordinates. But the position accuracy has frequently been degraded in this case when the car drove under the trees or other similar kinematical environments. That caused the larger velocity and acceleration errors. While the results from the carrier-phase method are std of the velocities = 2.1 mm/s, 1.3 mm/s, 3.7 mm/s in north, east, down, and std of the accelerations = 1.5 mm/s², 0.9 mm/s², 2.3 mm/s² for the static test period; as compared with KINPOS software results, std of the velocity difference between the carrier-phase method and the DGPS method = 7 mm/s, 6.9 mm/s, 9.7 mm/s in north, east, down direction, and std of acceleration difference = 5.0 mm/s², 4.5 mm/s², 7.5 mm/s² in north, east, down direction for the kinematical test period. Obviously, errors come from both the carrier-phase method and DGPS velocity and acceleration results derived directly by the position differentiation. In addition, better accuracy of positions than that before KF has been got by means of velocities and accelerations derived by the carrier-phase method after KF.     

不同GNSS在高纬度地区时间传递性能分析

全球卫星导航系统（GNSS）载波相位时间传递技术是高精度时间传递领域的主要研究方法之一，但目前关于该部分的研究主要集中在中低纬度地区，在高纬度地区并不多见。不同GNSS由于星座设计不同，在高纬度地区结构差异较大，因此需要对不同GNSS在高纬度地区的时间传递性能进行分析。实验结果表明，在高纬度地区时间传递中，Galileo稳定度最高，GPS和BDS次之，GLONASS最差。同时因在高纬度地区卫星的高度角普遍偏低，为合理平衡低高度角时可视卫星多和多路径误差大的矛盾，对不同截止高度角下获取的链路时间传递性能进行了分析。结果表明，在5°截止高度角下，高纬度地区的时间传递链路稳定性最好。     

微波辐射定标场地面接收机通道自校准设计

微波辐射定标场的地面接收机是卫星雷达外定标的主要设备之一，由于整个雷达系统对精度要求很高，因此作为系统外定标的地面接收机，其自身参数的实时校准就显得尤为重要。本文对地面接收机的接收通道设计了一种自校准方案，阐述了其校准原理和校准步骤，并给出了设计实现框图，分析了其中的关键技术。