基于MRAS的永磁同步电机无位置传感器控制策略研究

针对机械式传感器的使用会增加调速系统成本、故障率等问题,基于模型参考自适应系统(MRAS)设计了永磁同步电机(PMSM)无位置传感器矢量控制系统。推导了MRAS算法获取PMSM矢量调速系统转速与位置过程,给出了系统的自适应律选择,并证明了该系统满足Popov超稳定性条件,保证了系统渐进稳定。最后通过MATLAB/Simulink仿真软件搭建了仿真模型,仿真结果表明所设计的无位置传感器调速系统在负载突变以及转速动态变化等工况下具有良好的控制性能。     

Online condition diagnosis for a two-stage gearbox machinery of an aerospace utilization system using an ensemble multi-fault features indexing approach

China manned space station is designed to operate for over ten years. Long-term and sustainable research on space science and technology will be conducted during its operation. The application payloads must meet the ‘‘long life and high reliability" mission requirement. Gearbox machinery is one of the essential devices in an aerospace utilization system, failure of which may lead to downtime loss even during some disastrous catastrophes. A fault diagnosis of gearbox has attracted attentions for its significance in preventing catastrophic accidents and guaranteeing sufficient maintenance. A novel fault diagnosis method based on the Ensemble Multi-Fault Features Indexing(EMFFI) approach is proposed for the condition monitoring of gearboxes. Different from traditional methods of signal analysis in the one-dimensional space, this study employs a supervised learning method to determine the faults of a gearbox in a two-dimensional space using the classification model established by training the features extracted automatically from diagnostic vibration signals captured. The proposed method mainly includes the following steps. First, the vibration signals are transformed into a bi-spectrum contour map utilizing bi-spectrum technology,which provides a basis for the following image-based feature extraction. Then, Speeded-Up Robustness Feature(SURF) is applied to automatically extract the image feature points of the bi-spectrum contour map using a multi-fault features indexing theory, and the feature dimension is reduced by Linear Discriminant Analysis(LDA). Finally, Random Forest(RF) is introduced to identify the fault types of the gearbox. The test results verify that the proposed method based on the multi-fault features indexing approach achieves the target of high diagnostic accuracy and can serve as a highly effective technique to discover faults in a gearbox machinery such as a two-stage one.     

Experimental investigation on aero-heating of rudder shaft within laminar/turbulent hypersonic boundary layers

The aero-heating of the rudder shaft region of a hypersonic vehicle is very harsh, as the peak heat flux in this region can be even higher than that at the stagnation point. Therefore, studying the aero-heating of the rudder shaft is of great significance for designing the thermal protection system of the hypersonic vehicle. In the wind tunnel test of the aero-heating effect, we find that with the increase of the angle of attack of the lifting body model, the increasement of the heat flux of the rudder shaft is larger under laminar flow conditions than that under turbulent flow conditions. To understand this, we design a wind tunnel experiment to study the effect of laminar/turbulent hypersonic boundary layers on the heat flux of the rudder shaft under the same wind tunnel freestream conditions. The experiment is carried out in the ?2 m shock tunnel(FD-14 A) affiliated to the China Aerodynamics Research and Development Center(CARDC). The laminar boundary layer on the model is triggered to a turbulent one by using vortex generators, which are 2 mm-high diamonds. The aero-heating of the rudder shaft(with the rudder) and the protuberance(without the rudder) are studied in both hypersonic laminar and turbulent boundary layers under the same freestream condition. The nominal Mach numbers are 10 and 12, and the unit Reynolds numbers are2.4 × 10~6 m~(-1) and 2.1 × 10~6 m-1. The angle of attack of the model is 20°, and the deflection angle of the rudder and the protuberance is 10°. The heat flux on the model surface is measured by thin film heat flux sensors, and the heat flux distribution along the center line of the lifting body model suggests that forced transition is achieved in the upstream of the rudder. The test results of the rudder shaft and the protuberance show that the heat flux of the rudder shaft is lower in the turbulent flow than that in the laminar flow, but the heat flux of the protuberance is the other way around,i.e., lower in the laminar flow than in the turbulent flow. The wind tunnel test results is also validated by numerical simulations. Our analysis suggests that this phenomenon is due to the difference of boundary layer velocities caused by different thickness of boundary layer between laminar and turbulent flows, as well as the restricted flow within the rudder gap. When the turbulent boundary layer is more than three times thicker than that of the laminar boundary layer, the heat flux of the rudder shaft under the laminar flow condition is higher than that under the turbulent flow condition. Discovery of this phenomenon has great importance for guiding the design of the thermal protection system for the rudder shaft of hypersonic vehicles.     

不同校准装置对引压管腔动态特性校准

为了探索引压管腔在动态压力校准中各校准方法的一致性与数据准确性,确立了以简单直管形式引压管腔开展动态特性校准的研究。采用理论和仿真的手段分析并建立了引压管腔模型,理论模型和仿真结果一致性极高。利用3种正弦压力校准装置对同一引压管腔进行了动态校准组合试验,结果表明:3种校准方法所得的动态特性与理论分析趋势一致,对于引压管腔基频的校准各试验之间偏差小于0.55%,但与基频理论值最大偏差为-3.17%。该研究将会为未来引压管腔结构设计和动态特性的补偿修正提供了一定参考依据。      

封严篦齿特征参数对其密封性能影响的数值分析

利用软件CFX对直通型篦齿的内部流动进行模拟,研究了直通型篦齿齿距、转速对其泄漏量的影响.计算结果表明:篦齿泄漏量随齿距的增大而减少,篦齿转速对篦齿泄漏量的影响很小.另外,本文提出一种变齿距直通型篦齿,研究变齿距对篦齿泄漏量的影响,并对变齿距齿形所处位置对泄漏量的影响进行研究.     

α'-AlH_3的制备及形成研究

以LiAlH_4和AICI_3为原料,通过乙醚法制备了AlH_3,采用扫描电子显微镜(SEM)和X射线粉末颜射(XRD),研究了制备条件对产物形貌、晶型的影响规律。结果表明,氢化铝醚合物高温脱醚时,混合溶剂中乙醚比例是影响AlH_3晶型及形貌的主要因素,当结晶时,体系中乙醚不能及时除去,会导致α'-AlH_3的形成,且AlH_3形貌逐渐由立方体变成绒球状。伴生的α'型对AlH_3室温存储稳定性及安全性有较大影响,α'型存在加快AlH_3在室温下分解,且使得样品摩擦感度升高。     

复合材料带缠绕成型过程建模及工艺参数优化

复合材料带缠绕成型过程中,成型工艺参数的选取决定了缠绕制品的性能。采用正交实验法研究各工艺参数对缠绕制品层间剪切强度的影响规律和敏感度,并将正交试验数据与神经网络理论相结合,对带缠绕成型过程进行建模,得到缠绕成型工艺参数与层间剪切强度之间的非线性映射关系,并通过实验验证了模型的可靠性。在此基础上,利用粒子群优化方法在可行工艺参数域内对缠绕成型工艺参数进行优化。仿真与实验结果表明,基于神经网络模型的工艺参数粒子群优化算法能够快速、准确的得到带缠绕成型的全局最优工艺参数组合。使得缠绕制品层间剪切强度达到最优的工艺参数组合为:加热温度115℃,缠绕张力357 N,压辊压力1006 N和缠绕速度0.28 m/s,在最优工艺参数作用下,缠绕制品的层间剪切强度达到102.2 MPa。     

立式捏合机桨叶结构参数对混合釜流场影响的仿真分析

为揭示立式捏合机桨叶几何结构参数与混合釜流场之间的关系,以1 L两桨立式捏合机为研究对象,采用计算流体力学ANSYS Fluent 14.5软件对立式捏合机进行了三维模型仿真研究,分析了桨叶结构参数(桨桨间隙、桨叶螺旋角)的改变对混合物料挤压应力和剪切应力的影响。结果表明,增大桨桨间隙可减小桨叶对混合物料的挤压应力和剪切应力,空心桨螺旋角分别为40°、45°、50°,桨桨间隙由1.0 mm增加到3.0 mm,挤压应力、剪切应力分别平均减小了82.4%、57.23%;增大桨叶螺旋角可增大桨叶对混合物料的挤压应力和剪切应力,空心桨间隙分别为1.0、2.0 mm,桨叶螺旋角由35°增加到55°,挤压应力、剪切应力分别平均增加了92.8%、55.7%。     

含CL-20固体推进剂研究现状

综述了含CL-20(六硝基六氮杂异伍兹烷)固体推进剂,包括改性双基推进剂、高能低特征信号推进剂、NEPE推进剂以及其他类型固体推进剂的研究现状;主要涉及引入CL-20后固体推进剂的热分解特性、能量特性、燃烧性能、力学性能及安全性能等方面的内容;最后,总结了目前CL-20及含CL-20固体推进剂在实际的工程化应用过程中依然存在的一些尚未解决的难题,并指出了CL-20及含CL-20固体推进剂今后的研究方向及重点。     

阴影遮挡对太阳电池阵发电能力影响的仿真分析

航天器太阳电池阵的在轨发电能力会由于舱体等对太阳光的遮挡而受到影响。文章通过建立太阳电池电路模型,利用Saber仿真平台进行仿真,得到太阳电池单串电路遮挡片数与功率输出的关系曲线,利用MatLab进行了基于每个单串电池电路的遮挡计算,最终计算得到自主飞行阶段的阴影遮挡造成的太阳电池阵功率损失率。比较新计算方法与传统计算方法的计算结果表明,新方法的计算精度更高,尤其是在被遮挡的电池片数量较少时,新方法的优势更加突出。